Nissan Almera Tino V10. Manual — part 840
EM-16
[QG]
AIR CLEANER AND AIR DUCT
AIR CLEANER AND AIR DUCT
PFP:16500
Removal and Installation
EBS00QE7
REMOVAL
1.
Remove air cleaner case assembly, air duct and resonator.
●
Add marks as necessary for easier installation.
2.
Remove harness connector from mass air flow sensor.
3.
Remove mass air flow sensor.
CAUTION:
Handle mass air flow sensor with following cares.
●
Do not shock it.
●
Do not disassembly it.
●
Do not touch its sensor.
●
Do not deform mass air flow sensor's wire mesh.
4.
Remove left fender protector and resonator.
INSTALLATION
1.
Attach each joint aligning marks put at removal. Screw clamps firmly.
2.
Install in the reverse order of removal.
PBIC0533E
1.
Air cleaner case (upper)
2.
Resonator
3.
Air duct
4.
Mass air flow sensor
5.
O-ring
6.
Air cleaner case (lower)
7.
Grommet
8.
Air cleaner element
9.
Bracket
AIR CLEANER AND AIR DUCT
EM-17
[QG]
C
D
E
F
G
H
I
J
K
L
M
A
EM
Changing Air Cleaner Element
EBS00QE8
The viscous paper type filter does not need cleaning between
renewals.
SMA373C
EM-18
[QG]
INTAKE MANIFOLD
INTAKE MANIFOLD
PFP:14003
Removal and Installation
EBS00QE9
REMOVAL
WARNING:
To avoid the danger of being scalded, never drain the coolant when the engine is hot.
1.
Release fuel pressure.
Refer to
EC-52, "FUEL PRESSURE RELEASE"
(WITH EURO-OBD),
(WITHOUT EURO-OBD).
2.
Remove air duct and air cleaner case.
Refer to
EM-16, "Removal and Installation"
.
3.
Disconnect harness on engine top surface, and move it aside.
4.
Disconnect fuel injector/fuel tube assembly from intake manifold, and move it aside.
●
It is not necessary to disconnect fuel hose.
5.
Disconnect the following vacuum hoses.
6.
Disconnect blow-by hose (between intake manifold collector and rocker cover).
KBIA1363E
1.
Electric throttle control actuator
2.
Gasket
3.
Intake manifold collector
4.
EVAP canister purge volume control
solenoid valve
5.
Vacuum hose
6.
Vacuum hose
7.
Hose clamp
8.
Intake manifold support (front)
9.
Harness bracket
10. Vacuum hose
11. Intake manifold
12. PCV hose
13. Gasket
14. Vacuum hose
15. Gasket
16. Intake manifold support (rear)
17. Harness bracket
18. Intake manifold support (engine rear)
19. Grounding wire
INTAKE MANIFOLD
EM-19
[QG]
C
D
E
F
G
H
I
J
K
L
M
A
EM
7.
Loosen mounting bolts in reverse order shown in figure to
remove electric throttle control actuator.
CAUTION:
●
Do not shock it.
●
Do not disassembly and adjusting.
NOTE:
Remove intake manifold collector and electronic throttle control
as a single assembly, then remove electronic throttle control
itself.
8.
Remove bolt on cylinder head side of intake manifold collector.
9.
Loosen intake manifold collector nuts and bolts in reverse of the
order shown in the figure.
●
Do not remove intake manifold collector at this stage.
10. Move harness, which is fixed on intake manifold support, with bracket.
11. Remove intake manifold supports (rear, front, engine rear).
12. Loosen nuts and bolts in reverse order shown in the figure, and
remove intake manifold from cylinder head.
13. Disconnect intake manifold collector from intake manifold, and
pull out between engine and body.
PBIC0534E
KBIA1365E
KBIA1366E
PBIC0535E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст