Nissan Almera Tino V10. Manual — part 241
Hydraulic Circuit
NLBR0010
YBR362
Removal
NLBR0011
CAUTION:
I
Be careful not to splash brake fluid on painted areas; it
may cause paint damage. If brake fluid is splashed on
painted areas, wash it away with water immediately.
I
All hoses must be free from excessive bending, twisting
and pulling.
I
For ball & ramp type rear caliper, care should be taken as
not to let air enter the cylinder body.
1.
Remove flare nut connecting brake tube and hose, then with-
draw lock spring.
2.
Cover openings to prevent entrance of air and dirt whenever
disconnecting brake line.
Inspection
NLBR0012
Check brake lines (tubes and hoses) for cracks, deterioration or
other damage. Replace any damaged parts.
BRAKE HYDRAULIC LINE
Hydraulic Circuit
BR-12
SBR686C
Installation
NLBR0013
CAUTION:
I
Refill with new brake fluid “DOT 3” or “DOT 4”.
I
Never reuse drained brake fluid.
1.
Tighten all flare nuts and connecting bolts.
Specification:
Flare nut
14.8 - 17.6 N·m (1.5 - 1.7 kg-m, 11 - 12 ft-lb)
Connecting bolt
17 - 20 N·m (1.7 - 2.0 kg-m, 12 - 14 ft-lb)
2.
Refill until new brake fluid comes out of each air bleeder valve.
3.
Bleed air. Refer to “Bleeding Brake System”, BR-11, and ‘‘Air
Bleeding Procedure’’, CL-10.
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
ST
RS
BT
HA
SC
EL
IDX
BRAKE HYDRAULIC LINE
Installation
BR-13
Removal and Installation
NLBR0015
YBR360
SBR997
Inspection
NLBR0016
Check brake pedal for following items.
I
Brake pedal bend
I
Clevis pin deformation
I
Crack of any welded portion
I
Crack or deformation of clevis pin stopper
YBR361
Adjustment
NLBR0017
Check brake pedal free height from metal panel. Adjust if neces-
sary.
H: Free height
Refer to SDS, BR-154.
C
1
, C
2
: Clearance between pedal stopper and threaded
end of stop lamp switch and brake switch.
0.75 - 2.00 mm (0.0295 - 0.0787 in)
D: Depressed height
LHD/RHD (M/T): 60 -70 (2.36 - 2.76 in)
Under force of 490 N (50 kg, 110 lb) with engine run-
ning.
A: Pedal free play at pedal pad
1.0 - 3.0 mm (0.039 - 0.118 in)
BRAKE PEDAL AND BRACKET
Removal and Installation
BR-14
SBR229E
1.
Loosen lock nut and adjust pedal free height by turning brake
booster input rod. Then tighten lock nut.
2.
Check pedal free play.
Make sure that stop lamps go off when pedal is released.
3.
Check brake pedal’s depressed height while engine is running.
If lower than specification, check brake system for leaks, accu-
mulation of air or any damage to components (master cylinder,
wheel cylinder, etc.), then make necessary repairs.
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
ST
RS
BT
HA
SC
EL
IDX
BRAKE PEDAL AND BRACKET
Adjustment (Cont’d)
BR-15
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст