Nissan Almera Tino V10. Manual — part 159
AT-360
[ALL]
ACCELE RATOR PEDAL POSITION (APP) SENSOR
3.
CHECK INPUT SIGNAL (WITHOUT CONSULT-II)
Without CONSULT-II
1.
Turn ignition switch to “ON” position.
(Do not start engine.)
2.
Check voltage between TCM terminals 41 and 42 while acceler-
ator pedal is depressed slowly.
(Voltage rises gradually in response to throttle position.)
OK or NG
OK
>> GO TO 4
NG
>> Check harness for short or open between ECM and
TCM regarding throttle position sensor circuit. (Main harness)
4.
CHECK DTC
Perform
AT-357, "SELF-DIAGNOSIS CODE CONFIRMATION PROCEDURE"
.
OK or NG
OK
>> INSPECTION END
NG
>> 1. Perform TCM input/output signal inspection.
2. If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
Voltage:
Fully-closed throttle valve
:Approximately 0.5V
Fully-open throttle valve
:Approximately 4V
SCIA0710E
SHIFT SOLENOID VALVE A
AT-361
[ALL]
D
E
F
G
H
I
J
K
L
M
A
B
AT
SHIFT SOLENOID VALVE A
PFP:31940
Description
ECS009B3
Shift solenoid valves A and B are turned “ON” or “OFF” by the TCM
in response to signals sent from the PNP switch, vehicle speed and
throttle position sensors. Gears will then be shifted to the optimum
position.
TCM TERMINALS AND REFERENCE VALUE
Remarks: Specification data are reference values.
ON BOARD DIAGNOSIS LOGIC
SCIA0718E
Gear position
1
2
3
4
Shift solenoid valve A
ON (Closed)
OFF (Open)
OFF (Open)
ON (Closed)
Shift solenoid valve B
ON (Closed)
ON (Closed)
OFF (Open)
OFF (Open)
Termi-
nal No.
Wire color
Item
Condition
Judgement stan-
dard
(Approx.)
11
L/W
Shift solenoid
valve A
When shift solenoid valve A oper-
ates.
(When driving in “D
1
” or “D
4
”.)
Battery voltage
When shift solenoid valve A does not
operate.
(When driving in “D
2
” or “D
3
”.)
0V
Diagnostic trouble code
Malfunction is detected when...
Check items (Possible cause)
: SHIFT SOLENOID/VA
TCM detects an improper voltage drop
when it tries to operate the solenoid valve.
●
Harness or connectors
(The solenoid circuit is open or shorted.)
●
Shift solenoid valve A
: 4th judgement flicker
AT-362
[ALL]
SHIFT SOLENOID VALVE A
SELF-DIAGNOSIS CODE CONFIRMATION PROCEDURE
After the repair, perform the following procedure to confirm the malfunction is eliminated.
With CONSULT-II
1.
Start engine.
2.
Select “SELF-DIAG RESULTS” mode for A/T with CONSULT-II.
3.
Drive vehicle in D
1
→
D
2
position.
4.
IF DTC is detected, go to
AT-364, "Diagnostic Procedure"
.
Without CONSULT-II
1.
Start engine.
2.
Drive vehicle in D
1
→
D
2
position.
3.
Perform self-diagnosis.
Refer to
AT-252, "Diagnostic Procedure Without CONSULT-II"
.
4.
If DTC is detected, go to
AT-364, "Diagnostic Procedure"
.
SAT014K
SAT014K
MCIB9028E
SHIFT SOLENOID VALVE A
AT-363
[ALL]
D
E
F
G
H
I
J
K
L
M
A
B
AT
Wiring Diagram — AT — SSV/A
ECS009B4
YAT379A
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст