Nissan Almera Tino V10. Manual — part 162
AT-372
[ALL]
OVERRUN CLUTCH SOLENOID VALVE
SELF-DIAGNOSIS CODE CONFIRMATION PROCEDURE
After the repair, perform the following procedure to confirm the malfunction is eliminated.
With CONSULT-II
1.
Start engine.
2.
Select “SELF-DIAG RESULTS” mode for A/T with CONSULT-II.
3.
Drive vehicle under the following conditions:
Selector lever in “D” position, overdrive control switch in “OFF”
position and vehicle speed higher than 10 km/h (6 MPH).
4.
If DTC is detected, go to
AT-374, "Diagnostic Procedure"
.
Without CONSULT-II
1.
Start engine.
2.
Drive vehicle under the following conditions:
Selector lever in “D” position, overdrive control switch in “OFF”
position and vehicle speed higher than 10 km/h (6 MPH).
3.
Perform self-diagnosis.
Refer to
AT-252, "Diagnostic Procedure Without CONSULT-II"
for EXC. F/EURO-OBD,
for EURO-OBD.
4.
If DTC is detected, go to
AT-374, "Diagnostic Procedure"
.
SAT014K
SAT020K
MCIB9030E
OVERRUN CLUTCH SOLENOID VALVE
AT-373
[ALL]
D
E
F
G
H
I
J
K
L
M
A
B
AT
Wiring Diagram — AT — OVRCSV
ECS009BC
YAT382A
AT-374
[ALL]
OVERRUN CLUTCH SOLENOID VALVE
Diagnostic Procedure
ECS009BD
1.
CHECK VALVE RESISTANCE
1.
Turn ignition switch to “OFF” position.
2.
Disconnect terminal cord assembly connector in engine compartment.
3.
Check resistance between terminal 3 and ground.
OK or NG
OK
>> GO TO 2
NG
>> 1. Remove control valve assembly. Refer to
"Control Valve Assembly and Accumulators"
.
2. Check the following items:
Overrun clutch solenoid valve
Refer to
AT-375, "Component Inspection"
.
Harness of terminal cord assembly for short or open
2.
CHECK POWER SOURCE CIRCUIT
1.
Turn ignition switch to “OFF” position.
2.
Disconnect TCM harness connector.
3.
Check continuity between terminal 3 and TCM harness connector terminal 20.
If OK, check harness for short to ground and short to power.
4.
Reinstall any part removed.
OK or NG
OK
>> GO TO 3
NG
>> Repair open circuit or short to ground or short to power
in harness or connectors.
3.
CHECK DTC
Perform
AT-372, "SELF-DIAGNOSIS CODE CONFIRMATION PROCEDURE"
.
OK or NG
OK
>> INSPECTION END
NG
>> 1. Perform TCM input/output signal inspection.
2. If NG, recheck TCM pin terminals for damage or loose connection with harness connector.
Resistance
: 20 - 30
Ω
MCIA0097E
Continuity should exist.
MCIA0098E
OVERRUN CLUTCH SOLENOID VALVE
AT-375
[ALL]
D
E
F
G
H
I
J
K
L
M
A
B
AT
Component Inspection
ECS009BE
OVERRUN CLUTCH SOLENOID VALVE
●
For removal, refer to
AT-410, "Control Valve Assembly and Accumulators"
.
Resistance Check
●
Check resistance between two terminals.
Operation Check
●
Check solenoid valve by listening for its operating sound while
applying battery voltage to the terminal and ground.
Solenoid valve
Terminal No.
Resistance
(Approx.)
Overrun clutch
solenoid valve
3
Ground
20 - 30
Ω
MCIA0099E
MCIA0100E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст