Nissan Almera Tino V10. Manual — part 183
AT-456
[ALL]
REPAIR FOR COMPONENT PARTS
1-2 Accumulator Valve
●
Install 1-2 accumulator valve. Align 1-2 accumulator retainer
plate from opposite side of control valve body.
●
Install return spring, 1-2 accumulator piston and plug.
1.
Install retainer plates.
●
Install retainer plate while pushing plug or return spring.
Retainer Plate (Upper Body)
Unit: mm (in)
●
Install proper retainer plates.
Refer to
AT-453, "Control Valve Upper Body"
.
SAT142D
SAT143D
No.
Name of control valve
Width A
Length B
22
Pilot valve
6.0 (0.236)
21.5 (0.846)
30
1st reducing valve
34
3-2 timing valve
8
Torque converter relief valve
17
1-2 accumulator valve
38.5 (1.516)
25
1-2 accumulator piston
5
Overrun clutch reducing valve
24.0 (0.945)
21
Cooler check valve
13
Torque converter clutch control valve
28.0 (1.102)
SAT086F
REPAIR FOR COMPONENT PARTS
AT-457
[ALL]
D
E
F
G
H
I
J
K
L
M
A
B
AT
Control Valve Lower Body
ECS009CL
COMPONENTS
Numbers preceding valve springs correspond with those shown in
AT-519, "SERVICE DATA AND SPECIFI-
.
1.
Control valve lower body
2.
Return spring
3.
Shift valve B
4.
Plug
5.
Retainer plate
6.
Pressure modifier valve
7.
Return spring
8.
Parallel pin
9.
Sleeve
10. Piston
11.
Return spring
12. Retainer plate
13. Manual valve
14. Retainer plate
15. Sleeve
16. Plug
17. Spring seat
18. Return spring
19. Pressure regulator valve
20. Retainer plate
21. Plug
22. Overrun clutch control valve
23. Return spring
24. Retainer plate
25. Plug
26. Accumulator control valve
27. Return spring
28. Retainer plate
29. Return spring
30. Shift valve A
31. Retainer plate
32. Plug
33. Plug
34. Return spring
35. Shuttle control valve
SAT864J
AT-458
[ALL]
REPAIR FOR COMPONENT PARTS
DISASSEMBLY
●
Remove valves at retainer plate.
For removal procedures, refer to
.
INSPECTION
Valve Springs
●
Check each valve spring for damage or deformation. Also mea-
sure free length and outer diameter.
●
Replace valve springs if deformed or fatigued.
Control Valves
●
Check sliding surfaces of control valves, sleeves and plugs for damage.
ASSEMBLY
●
Install control valves.
For installation procedures, refer to
.
Retainer Plate (for control valve lower body)
Unit: mm (in)
●
Install proper retainer plates.
Refer to
AT-457, "Control Valve Lower Body"
.
SAT872J
Inspection standard
:Refer to
.
SAT138D
SAT872J
Name of control valve
No.
Length A
Length B
Type
Pressure regulator valve
14
6.0
(0.236)
28.0
(1.102)
I
Accumulator control valve
24
Shift valve A
28
Overrun clutch control valve
20
Pressure modifier valve
12
Shuttle control valve
31
Shift valve B
5
—
—
II
SAT089F
REPAIR FOR COMPONENT PARTS
AT-459
[ALL]
D
E
F
G
H
I
J
K
L
M
A
B
AT
Reverse Clutch
ECS009CM
COMPONENTS
DISASSEMBLY
1.
Check operation of reverse clutch
a.
Install seal ring onto drum support of oil pump cover and install
reverse clutch assembly. Apply compressed air to oil hole.
b.
Check to see that retaining plate moves to snap ring.
c.
If retaining plate does not contact snap ring:
●
D-ring might be damaged.
●
Oil seal might be damaged.
●
Fluid might be leaking past piston check ball.
2.
Remove snap ring.
3.
Remove drive plates, driven plates, retaining plate, and dish
plates.
4.
Set Tool on spring retainer and remove snap ring from reverse
clutch drum while compressing return springs.
●
Set Tool directly over springs.
●
Do not expand snap ring excessively.
5.
Remove spring retainer and return springs.
SAT485JA
SAT155D
SAT156D
AAT489
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст