Nissan Almera Tino V10. Manual — part 707
NEL664
Electrical Components Inspection
NLEL0051
FUEL WARNING LAMP OPERATION CHECK
NLEL0051S01
1.
Turn ignition switch “OFF”.
2.
Disconnect fuel level sensor unit harness connector B38.
3.
Connect a resistor (80
Ω
) between fuel level sensor unit har-
ness connector terminals 4 and 1.
4.
Turn ignition switch “ON”.
The fuel warning lamp should come on.
MEL425F
OIL PRESSURE SWITCH CHECK
NLEL0051S02
Oil pressure
kPa (bar, kg/cm
2
, psi)
Continuity
Engine running
More than 10 - 20
(0.10 - 0.20, 0.1 - 0.2,
1 - 3)
No
Engine not running
Less than 10 - 20
(0.10 - 0.20, 0.1 - 0.2,
1 - 3)
Yes
Check the continuity between the terminals of oil pressure switch
and body ground.
WARNING LAMPS
Electrical Components Inspection
EL-124
Component Parts and Harness Connector
Location
NLEL0452
YEL334E
System Description
NLEL0453
The warning chime is controlled by the smart entrance control unit.
The warning chime is located in the smart entrance control unit.
Power is supplied at all times
I
through 15A fuse [No. 5, located in fuse block (J/B)]
I
to smart entrance control unit terminal 56,
I
through 10A fuse [No. 12, located in the fuse block (J/B)]
I
to key switch terminal 1 (RHD models), and
I
through 10A fuse (No. 38, located in the fuse and fusible link box)
I
to lighting switch terminal 11.
With the ignition switch in the ON or START position, power is supplied
I
through 10A fuse [No. 10, located in the fuse block (J/B)]
I
to smart entrance control unit terminal 29.
Ground is supplied to smart entrance control unit terminal 53 through body grounds M28, M48, M109 (QG
engine models).
IGNITION KEY WARNING CHIME/FOR RHD MODELS
NLEL0453S01
With the key in the ignition switch in the OFF position, the driver’s door open, the warning chime will sound.
Power is supplied
I
from key switch terminal 2
I
to smart entrance control unit terminal 5.
Ground is supplied
I
from body grounds B24, B30 or D89 (LHD models)
I
through door switch driver side terminals 3 and 2
I
to smart entrance control unit terminal 43.
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
WARNING CHIME
Component Parts and Harness Connector Location
EL-125
LIGHT WARNING CHIME
NLEL0453S02
With ignition switch OFF, driver’s door open, and lighting switch in 1ST or 2ND position, warning chime will
sound. Power is supplied.
I
from lighting switch terminal 12
I
through daytime light control unit terminals 11 and 10 (with daytime light system)
I
to smart entrance control unit terminal 17
Ground is supplied
I
from door switch driver side terminal 2
I
to smart entrance control unit terminal 43.
Door switch driver side terminal 3 is grounded through body grounds B24, B30 or D89 (LHD models).
TRAILER DIRECTION INDICATOR WARNING CHIME
NLEL0453S04
This warning chime will be sounded while the direction indicator (turn signal lamp) is in operation with towing
the trailer.
This is an audible feedback (warning chime) to the driver.
If no audible feedback is heard while towing the trailer and operating the turn signal, this indicates the bulb
failure of the trailer.
Smart entrance control unit will detect the additional electrical load of a turn signal lamp for trailer automati-
cally. Then the chime will be sounded by the smart entrance control unit internally with the operation of the
turn signal.
WARNING CHIME
System Description (Cont’d)
EL-126
Wiring Diagram — CHIME —
NLEL0454
YEL962D
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
WARNING CHIME
Wiring Diagram — CHIME —
EL-127
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст