Nissan Almera Tino V10. Manual — part 743
FIG. 3
NLEL0504S16
YEL006E
POWER DOOR LOCK
Wiring Diagram — D/LOCK — (Cont’d)
EL-268
FIG. 4
NLEL0504S17
YEL007E
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
POWER DOOR LOCK
Wiring Diagram — D/LOCK — (Cont’d)
EL-269
MBIB0906E
Trouble Diagnosis
NLEL0572
CONSULT-II INSPECTION PROCEDURE “DOOR
LOCKING”
NLEL0572S01
1.
Turn ignition switch “OFF”.
2.
Connect CONSULT-II to the data link connector.
MBIB0233E
3.
Turn ignition switch “ON”.
4.
Touch “START (NISSAN BASED VHCL)”.
SIIA1678E
5.
Touch “SMART ENTRANCE”.
6.
Touch “DOOR LOCKING” or “TRUNK RELEASE”.
SIIA1677E
7.
Select diagnosis mode.
“DATA MONITOR” and “WORK SUPPORT” are available.
POWER DOOR LOCK
Trouble Diagnosis
EL-270
CONSULT-II APPLICATION ITEMS
=NLEL0572S02
Door Locking
NLEL0572S0201
DATA MONITOR
Monitored Item
Description
IGNITION SW
Indicates [ON/OFF] condition of ignition switch.
DOOR SW DR RR
Indicates [ON/OFF] condition of rear door switch (driver side).
DOOR SW AS RR
Indicates [ON/OFF] condition of rear door switch (passenger side).
AS DOOR SW
Indicates [ON/OFF] condition of front door switch (passenger side).
DR DOOR SW
Indicates [ON\OFF] condition of front door switch (driver side).
CDL LOCK SW
Indicates [ON/OFF] condition of lock signal from door lock/ unlock switch.
CDL UNLOCK SW
Indicates [ON/OFF] condition of unlock signal from door lock/ unlock switch.
RKE LOCK
Indicates [ON/OFF] condition of lock signal from remote controller.
RKE UNLOCK
Indicates [ON/OFF] condition of unlock signal from remote controller.
RKE SEL UNLOCK
Indicates [ON/OFF] condition of select unlock signal from remote controller.
KEY CYL LK
Indicates [ON/OFF] condition of lock signal from door key cylinder.
KEY CYL UNLK
Indicates [ON/OFF] condition of unlock signal from door key cylinder.
WORK SUPPORT
Monitored Item
Description
AUTO RE-LOCK
Auto re-lock function can be changed in this mode. The re-lock mode will be changed when
“CHANGE MODE” on CONSULT-II screen is touched.
SELECTIVE UNLOCK
Selective unlock function can be changed in this mode. The unlock mode will be changed when
“CHANGE SET” on CONSULT-II screen is touched.
SYMPTOM CHART
NLEL0572S03
First perform the “SELF-DIAG RESULTS” in “SMART ENTRANCE”
with CONSULT-II, when perform the each trouble diagnosis. Refer
to EL-270, “CONSULT-II INSPECTION PROCEDURE”.
Symptom
Malfunctioning system
Reference
page
Power door lock does not operate using any switch
Power supply and ground circuit check
Door lock actuator check
If above systems are OK, replace smart entrance con-
trol unit.
—
Power door lock does not operate with lock/unlock
switch.
Door lock/unlock switch check
If above system is OK, replace smart entrance control
unit.
—
Specific door lock actuator does not operate.
Door lock actuator check
*Key reminder system does not operate.
Door switch check
If above system is OK, replace smart entrance control
unit.
—
*: Make sure the power door lock system operates properly.
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
POWER DOOR LOCK
Trouble Diagnosis (Cont’d)
EL-271
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст