Nissan Almera Tino V10. Manual — part 758
MBIB0906E
CONSULT-II Inspection Procedure
NLEL0685
1.
Turn ignition switch “OFF”.
2.
Connect CONSULT-II to the data link connector.
MBIB0233E
3.
Turn ignition switch “ON”.
4.
Touch “START (NISSAN BASED VHCL)”.
SIIA1678E
5.
Touch “SMART ENTRANCE”.
SIIA1679E
6.
Touch “KEYLESS ENTRY”.
SIIA1677E
7.
Select diagnosis mode.
“DATA MONITOR” and “WORK SUPPORT” are available.
MULTI-REMOTE CONTROL SYSTEM
CONSULT-II Inspection Procedure
EL-328
CONSULT-II Application Items
NLEL0686
DATA MONITOR
Monitored Item
Description
IGNITION SW
Indicates [ON/OFF] condition of ignition switch in ON position.
TRUNK OPEN SW
Indicates [ON/OFF] condition of back door switch.
RKE LOCK
Indicates [ON/OFF] condition of lock signal from remote controller.
RKE UNLOCK
Indicates [ON/OFF] condition of unlock signal from remote controller.
RKE SEL UNLOCK
Indicates [ON/OFF] condition of select unlock signal from remote controller.
RKE TRUNK REL
Indicates [ON/OFF] condition of back door open signal from back door release switch.
BATTERY CHECK
Indicates [OK/NG] condition of remote controller battery.
MODE
Indicates [CMFRT/SCRTY] condition of multi-remote control system.
WORK SUPPORT
Test Item
Description
KEYLESS CHECK
It can be checked whether remote controller ID code is registered or not in this mode.
KEYLESS REGISTRATION
Remote controller ID code can be registered.
KEYLESS DI FLASH
This mode can be setting hazard reminder function.
I
MODE 1: Nothing
I
MODE 2: Lock operation only
I
MODE 3: Unlock operation only
I
MODE 4: Both lock and unlock operation
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
MULTI-REMOTE CONTROL SYSTEM
CONSULT-II Application Items
EL-329
Trouble Diagnoses
NLEL0482
SYMPTOM CHART
=NLEL0482S01
NOTE:
Always check remote controller battery before replacing remote
controller.
Symptom
Diagnoses/service procedure
Reference
page
(EL-
)
No doors can be locked or unlocked by remote
control operation.
(Make sure that power door lock operates properly.
If NG, check power door lock.)
1. Remote controller battery check
2. Power supply and ground circuit for time control unit check
3. Replace remote controller. Refer to ID Code Entry Proce-
dure.
The new ID of remote controller cannot be entered. 1. Remote controller battery check
2. Power supply and ground circuit for time control unit check
3. Ignition “ON” power supply circuit for time control unit
4. Replace remote controller. Refer to ID Code Entry Proce-
dure.
Hazard reminder does not activate properly when
pressing lock or unlock button of remote controller.
1. Remote controller battery
2. Hazard reminder check
3. Replace remote controller. Refer to ID Code Entry Proce-
dure.
Auto door lock does not activate properly. (All other
multi-remote control system functions are OK.)
1. Check auto door lock operation setting.
2. Replace smart entrance control unit.
—
Interior room lamp does not activate properly.
1. Check interior room lamp operation.
2. Check door switch.
3. Replace smart entrance control unit.
—
MULTI-REMOTE CONTROL SYSTEM
Trouble Diagnoses
EL-330
POWER SUPPLY AND GROUND CIRCUIT CHECK
=NLEL0482S03
1
CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect smart entrance control unit connector.
3. Check voltage between smart entrance control unit harness connector M101 terminal 56 (R/B) and ground.
YEL363E
MTBL1717
OK or NG
OK
©
GO TO 2.
NG
©
Check the following.
I
15A fuse [No. 5, located in fuse and fusible link box (J/B)]
I
Harness for open or short between smart entrance control unit and fuse
2
CHECK GROUND CIRCUIT
Check continuity between smart entrance control unit harness connector M101 terminal 53 (B) and ground.
SIIA1565E
MTBL1718
OK or NG
OK
©
Power supply and ground circuit is OK.
NG
©
Check smart entrance control unit ground circuit for open or short.
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
BR
ST
RS
BT
HA
SC
IDX
MULTI-REMOTE CONTROL SYSTEM
Trouble Diagnoses (Cont’d)
EL-331
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст