Nissan Almera Tino V10. Manual — part 255
MBIB0233E
2.
Touch “START (NISSAN BASED VHCL)” on the display.
PBR385C
3.
Touch “ABS”.
4.
Touch “ACTIVE TEST”.
5.
Test item selection screen is displayed.
6.
Touch test item.
7.
Touch “START” with “MAIN SIGNALS” line inverted.
8.
Active test screen is displayed.
SFIA0395E
Display Item List
NLBR0210S0402
ABS solenoid valve
Touch “UP”, “KEEP” and “DOWN”. Check ABS solenoid valves
(inlet/outlet) operate as the following chart using screen monitor.
Operation
Up
Keep
Down
ABS inlet S/V
OFF
ON
ON
ABS outlet S/V
OFF
OFF
ON*
*: ON for 1 to 2 seconds after touch, and then OFF
SFIA0396E
NOTE:
I
If active test is performed with brake pedal depressed, pedal
stroke may be changed. This is a normal condition.
I
“TEST STOP” is displayed 10 seconds later from the operation
start.
I
To perform test again after “TEST STOP” is displayed, repeat
step 6 of operation procedure.
SFIA0397E
ABS motor
Touch “ON” and “OFF” on screen. Check ABS motor relay operates
as shown in the following chart.
Operation
ON
OFF
ABS actuator
ON
ON
ABS motor
ON
OFF
NOTE:
I
If active test is performed with brake pedal depressed, pedal
stroke may be changed. This is a normal condition.
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION
ABS
CONSULT-II Functions (Cont’d)
BR-68
I
“TEST STOP” is displayed 10 seconds later from the operation
start.
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
ST
RS
BT
HA
SC
EL
IDX
ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION
ABS
CONSULT-II Functions (Cont’d)
BR-69
YBR380
ABS Actuator and Electric Unit
NLBR0211
Disconnect each ABS actuator and electric unit E1 (Type I), E217
(Type II) connector. Confirm continuity and resistance value
between each pair of ABS actuator and electric unit harness con-
nector.
CAUTION:
Be sure ABS motor is securely grounded.
Basic Inspection 1 Brake Fluid Level and
Leakage Inspection
NLBR0212
1.
Check fluid level in brake reservoir tank. If fluid level is low,
refill brake fluid.
2.
Check area around brake piping and ABS actuator and elec-
tric unit for leaks. If a leak or oozing is detected, check as fol-
lows:
I
If connections at ABS actuator and electric unit are loose,
tighten piping to the specified torque. Then check again for
leaks, and be sure there is no fluid leak.
I
If the flare nuts at the connections and the threads of the ABS
actuator and electric unit are damaged, replace the damaged
parts. Then check again for leaks, and make sure that there is
no fluid leak.
I
If leak or oozing is detected except for ABS actuator and elec-
tric unit connections, wipe it with clean cloth. Then check again
for leaks. If there is still leak or oozing, replace damaged part.
I
If leak or oozing is detected on ABS actuator and electric unit,
wipe with a clean cloth. Check again for leaks, and if there is
still leak or oozing, replace ABS actuator and electric unit.
CAUTION:
ABS actuator and electric unit body cannot be disassembled.
Basic Inspection 2 Inspection for Loose Power
Supply Terminal
NLBR0213
Check battery for looseness on battery positive/negative terminals
and ground connection.
TROUBLE DIAGNOSIS — BASIC INSPECTION
ABS
ABS Actuator and Electric Unit
BR-70
Basic Inspection 3 ABS Warning Lamp
Inspection
NLBR0214
1.
Be sure ABS warning lamp turns on when ignition switch is
turned ON. If it does not turn on, check CAN communications.
Refer
to
If
there
are
no
errors
with
CAN
communications, check ABS warning lamp harness.
2.
Be sure ABS warning lamp turns off after approximately 1
second when ignition switch is turned ON. If it does not turn off,
perform self-diagnosis.
3.
After driving the vehicle at Approx. 30 km/h (19 MHP) for a few
seconds, check ABS warning lamp do not illuminate.
4.
After completing the self-diagnosis, always erase the diagno-
sis memory.
GI
MA
EM
LC
EC
FE
CL
MT
AT
AX
SU
ST
RS
BT
HA
SC
EL
IDX
TROUBLE DIAGNOSIS — BASIC INSPECTION
ABS
Basic Inspection 3 ABS Warning Lamp Inspection
BR-71
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст