Nissan Almera Tino V10. Manual — part 405
EC-446
[QG (WITH EURO-OBD)]
DTC P1146, P1166 HO2S2 (A/T MODELS)
BANK 2
YEC448A
DTC P1146, P1166 HO2S2 (A/T MODELS)
EC-447
[QG (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Do not use ECM ground terminals when measuring input/output voltage. Doing so may result in dam-
age to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
Diagnostic Procedure
EBS00QQY
1.
RETIGHTEN GROUND SCREWS
1.
Turn ignition switch “OFF”.
2.
Loosen and retighten engine ground screws.
>> GO TO 2.
TER-
MINAL
NO.
WIRE
COLOR
ITEM
CONDITION
DATA (DC Voltage)
17
L
Heated oxygen sensor 2
(bank 2)
[Engine is running]
●
Warm-up condition
●
Engine speed is 3,000 rpm quickly after the fol-
lowing conditions are met.
–
Keeping the engine speed between 3,500 and
4,000 rpm for one minute and at idle for one
minute under no load
0 - Approximately 1.0V
74
B
Sensors' ground
(Heated oxygen sensor)
[Engine is running]
●
Idle speed
Approximately 0V
MBIB0095E
EC-448
[QG (WITH EURO-OBD)]
DTC P1146, P1166 HO2S2 (A/T MODELS)
2.
CLEAR THE SELF-LEARNING DATA
With CONSULT-II
1.
Start engine and warm it up to normal operating temperature.
2.
Select “SELF-LEARNING CONT” in “WORK SUPPORT” mode
with CONSULT-II.
3.
Clear the self-learning control coefficient by touching “CLEAR”.
4.
Run engine for at least 10 minutes at idle speed.
Is the 1st trip DTC P0172 or P0175 detected?
Is it difficult to start engine?
Without CONSULT-II
1.
Start engine and warm it up to normal operating temperature.
2.
Turn ignition switch “OFF”.
3.
Disconnect mass air flow sensor harness connector, and restart
and run engine for at least 5 seconds at idle speed.
4.
Stop engine and reconnect mass air flow sensor harness con-
nector.
5.
Make sure that DTC P0102 is displayed.
6.
Erase the DTC memory. Refer to
EMISSION-RELATED DIAGNOSTIC INFORMATION"
.
7.
Make sure that DTC P0000 is displayed.
8.
Run engine for at least 10 minutes at idle speed.
Is the 1st trip DTC P0172 or P0175 detected?
Is it difficult to start engine?
Yes or No
Yes
>> Perform trouble diagnosis for DTC P0172, P0175. Refer to
.
No
>> GO TO 3.
3.
CHECK HO2S2 GROUND CIRCUIT FOR OPEN AND SHORT
1.
Turn ignition switch “OFF”.
2.
Disconnect heated oxygen sensor 2 harness connector.
3.
Disconnect ECM harness connector.
4.
Check harness continuity between ECM terminal 74 and HO2S2
terminal 3.
Refer to Wiring Diagram.
5.
Also check harness for short to ground and short to power.
OK or NG
OK
>> GO TO 4.
NG
>> Repair open circuit or short to ground or short to power
in harness or connectors.
SEF215Z
MBIB0096E
Continuity should exist.
MBIB0094E
DTC P1146, P1166 HO2S2 (A/T MODELS)
EC-449
[QG (WITH EURO-OBD)]
C
D
E
F
G
H
I
J
K
L
M
A
EC
4.
CHECK HO2S2 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.
Check harness continuity between ECM terminal and HO2S2 terminal as follows.
Refer to Wiring Diagram.
2.
Check harness continuity between the following terminals and ground.
Refer to Wiring Diagram.
3.
Also check harness for short to power.
OK or NG
OK
>> GO TO 5.
NG
>> Repair open circuit or short to ground or short to power in harness or connectors.
5.
CHECK HEATED OXYGEN SENSOR 2
Refer to
EC-449, "Component Inspection"
.
OK or NG
OK
>> GO TO 6.
NG
>> Replace heated oxygen sensor 2.
6.
CHECK INTERMITTENT INCIDENT
Refer to
EC-138, "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT"
.
>> INSPECTION END
Component Inspection
EBS00QQZ
HEATED OXYGEN SENSOR 2
With CONSULT-II
1.
Start engine and warm it up to the normal operating temperature.
2.
Turn ignition switch “OFF” and wait at least 10 seconds.
3.
Start engine and keep the engine speed between 3,500 and 4,000 rpm for at least one minute under no
load.
4.
Let engine idle one minute.
DTC
Terminals
Bank
ECM
Sensor
P1146
16
2
1
P1166
17
2
2
Continuity should exist.
DTC
Terminals
Bank
ECM
Sensor
P1146
16
2
1
P1166
17
2
2
Continuity should not exist.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст