Nissan Almera Tino V10. Manual — part 868
EM-128
[YD]
EXHAUST MANIFOLD AND TURBOCHARGER
EXHAUST MANIFOLD AND TURBOCHARGER
PFP:14004
Removal and Installation
EBS00QFF
MBIA0005E
1.
Electronic EGR volume control valve 2.
Gasket
3.
EGR tube
4.
Air inlet pipe
5.
Exhaust manifold and turbocharger
assembly
6.
Oil return hose
7.
Turbo insulator
8.
Exhaust manifold insulator
9.
Air inlet pipe
10.
Oil feed tube
EXHAUST MANIFOLD AND TURBOCHARGER
EM-129
[YD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
REMOVAL
1.
Drain engine coolant. Refer to LC-40, “Changing Engine Coolant”.
2.
Remove engine cover. Refer to
EM-160, "Removal and Installation"
.
3.
Remove air duct and air inlet pipe. Refer to
EM-119, "Removal and Installation"
.
4.
Remove engine undercover.
5.
Remove radiator upper and lower hoses. Refer to LC-39, “Radiator”.
6.
Remove radiator and radiator fan. Refer to LC-39, “Radiator”.
7.
Remove air inlet pipe.
8.
Disconnect exhaust front tube.
9.
Remove catalyst. Refer to
EM-126, "Removal and Installation"
.
10. Remove exhaust manifold cover.
11. Remove insulator.
12. Each wiring and piping (disconnect/move)
1.
Electronic EGR volume control valve 2.
Gasket
3.
EGR tube
4.
Air inlet pipe
5.
Exhaust manifold and turbocharger
assembly
6.
Oil return hose
7.
Turbo insulator
8.
Exhaust manifold insulator
9.
Air inlet pipe
10.
Oil feed tube, oil return tube
MBIA0006E
EM-130
[YD]
EXHAUST MANIFOLD AND TURBOCHARGER
13. Loosen exhaust manifold mounting nuts in the reverse order
specified in the figure.
14. Rotate the exhaust manifold and turbocharger assembly so that
the rear side (EGR tube mounting side) faces upward. And then
pull out the assembly from between the engine and the air con-
ditioning piping.
CAUTION:
Be careful not to deform each turbocharger piping when pulling
out the assembly.
INSTALLATION
●
When a stud bolt is pulled out, tighten it to the following torque:
●
Tighten the exhaust manifold mounting nuts in the following procedure:
1.
Tighten the nuts in the order specified in the figure.
2.
Re-tighten the nuts 1 to 4.
3.
Install the gasket so that the alignment protrusion faces the No.
4 port.
4.
Install in reverse order of removal.
INSPECTION AFTER INSTALLATION
Start engine and raise engine speed to check no exhaust emission leaks.
JEM266G
: 12.7 - 16.7 N·m (1.3 - 1.7 kg-m, 9 - 12 ft-lb)
JEM266G
EXHAUST MANIFOLD AND TURBOCHARGER
EM-131
[YD]
C
D
E
F
G
H
I
J
K
L
M
A
EM
Disassembly and Assembly
EBS00QFG
MBIA0007E
1.
Exhaust manifold
2.
Gasket
3.
Oil return tube
4.
Oil feed tube
5.
Turbocharger
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст