Nissan Maxima (2022 year). Manual in english — page 22

If the ABS warning light illuminates during
the self-test or while driving, have the ve-
hicle checked. It is recommended that you
visit a NISSAN dealer for this service.

Normal operation

The Anti-lock Braking System (ABS) oper-
ates at speeds above 3 - 6 mph (5 - 10
km/h). The speed varies according to road
conditions.

When the ABS senses that one or more
wheels are close to locking up, the actuator
rapidly applies and releases hydraulic pres-
sure. This action is similar to pumping the
brakes very quickly. You may feel a pulsa-
tion in the brake pedal and hear a noise
from under the hood or feel a vibration
from the actuator when it is operating. This
is normal and indicates that the ABS is op-
erating properly. However, the pulsation
may indicate that road conditions are haz-
ardous and extra care is required while
driving.

BRAKE ASSIST

When the force applied to the brake pedal
exceeds a certain level, the Brake Assist is
activated generating greater braking force
than a conventional brake booster even
with light pedal force.

WARNING

The Brake Assist is only an aid to assist
braking operation and is not a collision
warning or avoidance device. It is the
driver’s responsibility to stay alert,
drive safely and be in control of the ve-
hicle at all times.

The VDC system uses various sensors to
monitor driver inputs and vehicle motion.
Under certain driving conditions, the VDC
system helps to perform the following
functions:
• Controls brake pressure to reduce wheel

slip on one slipping drive wheel so power
is transferred to a non-slipping drive
wheel on the same axle.

• Controls brake pressure and engine out-

put to reduce drive wheel slip based on
vehicle speed (traction control function).

• Controls brake pressure at individual

wheels and engine output to help the
driver maintain control of the vehicle in
the following conditions:

– Understeer (vehicle tends to not follow

the steered path despite increased
steering input)

– Oversteer (vehicle tends to spin due to

certain road or driving conditions)

The VDC system can help the driver to
maintain control of the vehicle, but it can-
not prevent loss of vehicle control in all driv-
ing situations.

VEHICLE DYNAMIC CONTROL (VDC)
SYSTEM

5-114

Starting and driving

When the VDC system operates, the
indicator light in the instrument panel
flashes to note the following:
• The road may be slippery or the system

may determine some action is required
to help keep the vehicle on the steered
path.

• You may feel a pulsation in the brake

pedal and hear a noise or vibration from
under the hood. This is normal and indi-
cates that the VDC system is working
properly.

• Adjust your speed and driving to the road

conditions.

For additional information, see “Slip indica-
tor light” (P. 2-15) and “Vehicle Dynamic Con-
trol (VDC) OFF indicator light” (P. 2-15).

If a malfunction occurs in the system, the

indicator light comes on in the instru-

ment panel. The VDC system automatically
turns off when the indicator light is on.

The VDC OFF switch is used to turn off the
VDC system. The

, RAB, and AEB with

Pedestrian Detection indicator lights illumi-
nate to indicate the VDC, RAB, and AEB with
Pedestrian Detection systems are off.

When the VDC OFF switch is used to turn off
the system, the VDC system still operates
to prevent one drive wheel from slipping by
transferring power to a non-slipping drive
wheel. The

indicator light flashes if this

occurs. All other VDC functions are off and
the

indicator light will not flash.

The VDC system is automatically reset to
ON when the ignition switch is placed in the
OFF position then back to the ON position.

The computer has a built-in diagnostic fea-
ture that tests the system each time you
start the engine and move the vehicle for-
ward or in reverse at a slow speed. When
the self-test occurs, you may hear a clunk
noise and/or feel a pulsation in the brake
pedal. This is normal and is not an indica-
tion of a malfunction.

WARNING

•

The VDC system is designed to help
the driver maintain stability but does
not prevent accidents due to abrupt
steering operation at high speeds or
by careless or dangerous driving
techniques. Reduce vehicle speed
and be especially careful when driv-
ing and cornering on slippery sur-
faces and always drive carefully.

•

Do not modify the vehicle's suspen-
sion. If suspension parts such as
shock absorbers, struts, springs, sta-
bilizer bars, bushings and wheels are
not NISSAN recommended for your
vehicle or are extremely deterio-
rated, the VDC system may not oper-
ate properly. This could adversely af-
fect vehicle handling performance,
and the

indicator light may

flash.

•

If brake related parts such as brake
pads, rotors and calipers are not
NISSAN recommended or are ex-
tremely deteriorated, the VDC sys-
tem may not operate properly and
the

indicator

light

may

illuminate.

•

If engine control related parts are not
NISSAN recommended or are ex-
tremely deteriorated, the

indi-

cator light may illuminate.

•

When driving on extremely inclined
surfaces such as higher banked cor-
ners, the VDC system may not oper-
ate properly and the

indicator

light may flash. Do not drive on these
types of roads.

Starting and driving

5-115

•

When driving on an unstable surface
such as a turntable, ferry, elevator or
ramp, the

indicator light may

flash. This is not a malfunction. Re-
start the engine after driving onto a
stable surface.

•

If wheels or tires other than the
NISSAN

recommended

ones

are

used, the VDC system may not oper-
ate properly and the

indicator

light may flash.

•

The VDC system is not a substitute
for winter tires or tire chains on a
snow covered road.

BRAKE FORCE DISTRIBUTION

During braking while driving through turns,
the system optimizes the distribution of
force to each of the four wheels depending
on the radius of the turn.

WARNING

•

The VDC system is designed to help
the driver maintain stability but does
not prevent accidents due to abrupt
steering operation at high speeds or
by careless or dangerous driving
techniques. Reduce vehicle speed
and be especially careful when driv-
ing and cornering on slippery sur-
faces and always drive carefully.

•

Do not modify the vehicle's suspen-
sion. If suspension parts such as
shock absorbers, struts, springs, sta-
bilizer bars, bushings and wheels are
not NISSAN recommended for your
vehicle or are extremely deterio-
rated, the VDC system may not oper-
ate properly. This could adversely af-
fect vehicle handling performance,
and the

indicator light may

flash.

•

If brake related parts such as brake
pads, rotors and calipers are not
NISSAN recommended or are ex-
tremely deteriorated, the VDC sys-
tem may not operate properly and
the

indicator

light

may

illuminate.

•

If engine control related parts are not
NISSAN recommended or are ex-
tremely deteriorated, the

indi-

cator light may illuminate.

•

When driving on extremely inclined
surfaces such as higher banked cor-
ners, the VDC system may not oper-
ate properly and the

indicator

light may flash. Do not drive on these
types of roads.

•

When driving on an unstable surface
such as a turntable, ferry, elevator or
ramp, the

indicator light may

flash. This is not a malfunction. Re-
start the engine after driving onto a
stable surface.

•

If wheels or tires other than the
NISSAN

recommended

ones

are

used, the VDC system may not oper-
ate properly and the

indicator

light may flash.

•

The VDC system is not a substitute
for winter tires or tire chains on a
snow covered road.

5-116

Starting and driving

The Integrated Dynamics-control Module
is an electric control module that includes
the following functions:
• Intelligent Trace Control
• Intelligent Engine Brake
• Active Ride Control

INTELLIGENT TRACE CONTROL
(I-TC)

This system senses driving based on the
driver’s steering and acceleration/braking
patterns, and controls brake pressure at
individual wheels to aid tracing at corners
and help smooth vehicle response.

The I–TC can be set to ON (enabled) or OFF
(disabled) through the vehicle information
display “Settings” page. For additional infor-
mation, see “Vehicle information display”
(P. 2-17).

When the VDC OFF switch is used to turn off
the VDC system, the I–TC is also turned off.

If

the

Chassis

Control

System

Error

warning message appears in the vehicle
information display, it may indicate that the
I–TC is not functioning properly. Have the
system checked as soon as possible. It is
recommended that you visit a NISSAN
dealer for this service.

WARNING

The I–TC may not be effective depend-
ing on the driving condition. Always
drive carefully and attentively.

When the I–TC is operating, you may feel a
pulsation in the brake pedal and hear a
noise. This is normal and indicates that the
I–TC is operating properly.

Even if the I–TC is set to OFF, some func-
tions will remain on to assist the driver (for
example, avoidance scenes).

INTELLIGENT ENGINE BRAKE (I-EB)

The I–EB function adds subtle deceleration
by controlling the Continuously Variable
Transmission (CVT) gear ratio, depending
on the cornering condition calculated from
the driver's steering input and plural sen-
sors. This benefit is for easier traceability
and less workload of adjusting speed with
braking at corners.

The I–EB also enhances braking feel by
adding subtle deceleration with the CVT
gear ratio control according to the driver's
brake pedal operation.

The I–EB can be set to ON (enabled) or OFF
(disabled) through the vehicle information
display “Settings” page. For additional infor-
mation, see “Vehicle information display”
(P. 2-17).

If

the

Chassis

Control

System

Error

warning message appears in the vehicle
information display, it may indicate that the
I–EB is not functioning properly. Have the
system checked as soon as possible. It is
recommended that you visit a NISSAN
dealer for this service.

WARNING

The I–EB may not be effective depend-
ing on driving conditions. Always drive
carefully and attentively.

When the I–EB is operating, the needle of
the tachometer will rise up and you may
hear an engine noise. This is normal and
indicates

that

the

I–EB

is

operating

properly.

INTEGRATED DYNAMICS-CONTROL
MODULE

Starting and driving

5-117

ACTIVE RIDE CONTROL (ARC)

This system senses upper body motion
(based on wheel speed information) and
controls engine torque and four wheel
brake pressure. This will enhance ride com-
fort in effort to restrain uncomfortable up-
per body movement when passing over
undulated road surfaces. This system
comes into effect above 25 mph (40 km/h).

When the VDC OFF switch is used to turn off
the VDC system, the ARC is also turned off.

If

the

Chassis

Control

System

Error

warning message appears in the vehicle
information display, it may indicate that the
ARC is not functioning properly. Have the
system checked as soon as possible. It is
recommended that you visit a NISSAN
dealer for this service.

When the ARC is operating, you may hear
noise and sense slight deceleration. This is
normal and indicates that the ARC is oper-
ating properly.

The sonar (parking sensor) system sounds
a tone to inform the driver of obstacles
near the bumper.

When the “DISPLAY” key is ON, the sonar
view will automatically appear in the meter.

WARNING

•

The sonar (parking sensor) system is
a convenience but it is not a substi-
tute for proper parking.

•

The driver is always responsible for
safety during parking and other ma-
neuvers. Always look around and
check that it is safe to do so before
parking.

•

Read and understand the limitations
of the sonar (parking sensor) system
as contained in this section. The col-
ors of the corner sonar indicator and
the distance guide lines in the front/
rear view indicate different distances
to the object.

•

Inclement

weather

or

ultrasonic

sources such as an automatic car
wash,

a

truck's

compressed-air

brakes or a pneumatic drill may af-
fect the function of the system; this
may include reduced performance or
a false activation.

•

This function is designed as an aid to
the driver in detecting large station-
ary objects to help avoid damaging
the vehicle.

•

The system is not designed to pre-
vent contact with small or moving
objects. Always move slowly. The
system will not detect small objects
below the bumper, and may not de-
tect objects close to the bumper or
on the ground.

LSD2427

FRONT AND REAR SONAR SYSTEM (if
so equipped)

5-118

Starting and driving

•

The system may not detect the fol-
lowing objects: fluffy objects such as
snow, cloth, cotton, glass, wool, etc.,
and thin objects such as rope, wire
and chain, etc., or wedge-shaped
objects.

•

The sonar sensors may cause mal-
function when a horn, etc. sounds or
there is an ultrasonic source (such as
parking sensors of other vehicles)
around the vehicle because the so-
nar sensors detect the distance be-
tween the vehicle and the obstacle
by detecting the sound wave re-
flected

from

the

surface

of

an

obstacle.

If your vehicle sustains damage to the
bumper fascia, leaving it misaligned or
bent, the sensing zone may be altered
causing inaccurate measurement of ob-
stacles or false alarms.

CAUTION

•

Excessive noise (such as audio sys-
tem volume or an open vehicle win-
dow) will interfere with the tone and
it may not be heard.

•

Keep the sonar sensors (located on
the bumper fascia) free from snow,
ice and large accumulations of dirt.
Do not clean the sensors with sharp
objects. If the sensors are covered,
the accuracy of the sonar function
will be diminished.

SYSTEM OPERATION

The system informs with a visual and au-
dible alert of front obstacles when the shift
lever is in the D (Drive) position and both
front and rear obstacles when the shift le-
ver is in the R (Reverse) position.

Sonar Operation Table

FR Sensor

RR Sensor

Range Sound Display Sound

Dis-

play

P

x

†

x

†

R

o

o

o

o

N

x

†

x

†

D

o

o

x

†

o – Display/Beep when detect

† – Display on camera view

x – No Display and Beep

The system is deactivated at speeds above
6 mph (10 km/h). It is reactivated at lower
speeds.

While the vehicle is moving the audible alert
will stop after 3 seconds when an obstacle
is detected by only the corner sensor and
distance does not change. The audible
alert will also stop when the obstacle
moves away from the vehicle. At any time
the left side button of the steering wheel (

buttons) is available to cancel the au-

dible alert.

When the object is detected, the indicator
(green) appears and blinks and the tone
sounds intermittently. When the vehicle
moves closer to the object, the color of the
indicator turns yellow and the rate of the
blinking increases. When the vehicle is very
close to the object, the indicator stops
blinking and turns red, and the tone
sounds continuously.

Starting and driving

5-119

When the corner of the vehicle moves
closer to an object, the corner sonar indi-
cator

O

A

appears.

The system indicators

O

A

will appear when

the vehicle moves closer to an object.

LSD2428

LSD2137

5-120

Starting and driving

HOW TO ENABLE/DISABLE THE
FRONT AND REAR SONAR SYSTEM

The system is automatically activated
when the ignition is in the ON position and
the shift lever is in the R (Reverse) position.

Perform the following steps to enable or
disable the sonar system:

1. Press the

button until “Settings” ap-

pears in the vehicle information display
and then press OK. Use the

button

to select “Driver Assistance.” Then press
the OK button.

2. Select “Parking Aids” and press the OK

button.

3. Select “Sensor” and press the OK button,

then select “ON”, “OFF” or “Front Only” (if
so equipped) and press the OK button.

• Select “Display” to display the parking

sensor in the vehicle information dis-
play when the sonar system activates.

• Select “Volume” to change the volume

to “High”, “Medium”, or “Low”.

• Select “Range” to change the sonar

distance to “Near”, “Mid”, or “Far”.

LSD2820

Starting and driving

5-121

SONAR LIMITATIONS

WARNING

Listed below are the system limitations
for the sonar system. Failure to operate
the vehicle in accordance with these
system limitations could result in seri-
ous injury or death.

•

The system is deactivated at speeds
above 6 mph (10 km/h). It is reacti-
vated at lower speeds.

•

Inclement

weather

or

ultrasonic

sources such as an automatic car
wash,

a

truck’s

compressed-air

brakes or a pneumatic drill may af-
fect the function of the system; this
may include reduced performance or
a false activation.

•

The system is not designed to pre-
vent contact with small or moving
objects. Always move slowly. The
system will not detect small objects
below the bumper or on the ground.

•

The system may not detect the fol-
lowing objects: fluffy objects such as
snow, cloth, cotton, glass-wool, etc.;
thin objects such as rope, wire and
chain, etc.; or wedge-shaped objects.

•

The system may not detect objects
at speeds above 3 mph (5 km/h) and
may not detect certain angular or
moving objects.

•

Do not attach stickers (including
transparent material), install acces-
sories, or apply anything blocking
the sensors. These conditions may
reduce the ability of the system.

SYSTEM TEMPORARILY
UNAVAILABLE

When sonar blockage is detected, the sys-
tem will be deactivated automatically.

The system is not available until the condi-
tions no longer exist.

The sonar sensors may be blocked by tem-
porary ambient conditions such as splash-
ing water, mist or fog. The blocked condi-
tion may also be caused by objects such as
ice, frost or dirt obstructing the sonar
sensors.

Action to take:

When the above conditions no longer exist,
the system will resume automatically.

SYSTEM MAINTENANCE

The sonar sensors

O

A

and

O

B

are located

on the front and rear bumpers. Always
keep the area near the sonar sensors
clean.

LSD4570

5-122

Starting and driving

The sonar sensors may be blocked by tem-
porary ambient conditions such as splash-
ing water, mist or fog.

The blocked condition may also be caused
by objects such as ice, frost or dirt ob-
structing the sonar sensors.

Check for and remove objects obstructing
the area around the sonar sensors.

Do not attach stickers (including transpar-
ent material), install accessories or apply
additional paint near the sonar sensors.

Do not strike or damage the area around
the sonar sensors. It is recommended that
you visit a NISSAN dealer if the area around
the sonar sensors is damaged due to a
collision.

FREEING A FROZEN DOOR LOCK

To prevent a door lock from freezing, apply
de-icer through the key hole. If the lock
becomes frozen, heat the key before in-
serting it into the key hole or use the re-
mote keyless entry function on the Intelli-
gent Key.

ANTIFREEZE

In the winter when it is anticipated that the
temperature will drop below 32°F (0°C),
check the antifreeze to assure proper win-
ter protection. For additional information,
see “Engine cooling system” (P. 8-4).

BATTERY

If the battery is not fully charged during
extremely cold weather conditions, the
battery fluid may freeze and damage the
battery. To maintain maximum efficiency,
the battery should be checked regularly.
For additional information, see “Battery”
(P. 8-13).

DRAINING OF COOLANT WATER

If the vehicle is to be left outside without
antifreeze, drain the cooling system, includ-
ing the engine block. Refill before operating
the vehicle. For additional information, see
“Changing engine coolant” (P. 8-5).

TIRE EQUIPMENT

1. SUMMER tires have a tread designed to

provide superior performance on dry
pavement. However, the performance of
these tires will be substantially reduced
in snowy and icy conditions. If you oper-
ate your vehicle on snowy or icy roads,
NISSAN recommends the use of MUD &
SNOW or ALL SEASON TIRES on all four
wheels. It is recommended that you visit
a NISSAN dealer for the tire type, size,
speed rating and availability information.

2. For additional traction on icy roads,

studded tires may be used. However,
some U.S. states and Canadian prov-
inces prohibit their use. Check local,
state and provincial laws before install-
ing studded tires.

Skid and traction capabilities of studded
snow tires on wet or dry surfaces may be
poorer than that of non-studded snow
tires.

SPECIAL WINTER EQUIPMENT

It is recommended that the following items
be carried in the vehicle during winter:
• A scraper and stiff-bristled brush to re-

move ice and snow from the windows
and wiper blades.

COLD WEATHER DRIVING

Starting and driving

5-123

• A sturdy, flat board to be placed under the

jack to give it firm support.

• A shovel to dig the vehicle out of

snowdrifts.

• Extra washer fluid to refill the windshield-

washer fluid reservoir.

DRIVING ON SNOW OR ICE

WARNING

•

Wet ice (32°F, 0°C and freezing rain),
very cold snow or ice can be slick and
very hard to drive on. The vehicle will
have much less traction or “grip” un-
der these conditions. Try to avoid
driving on wet ice until the road is
salted or sanded.

•

Whatever the condition, drive with
caution. Accelerate and slow down
with care. If accelerating or down-
shifting too fast, the drive wheels will
lose even more traction.

•

Allow more stopping distance under
these conditions. Braking should be
started

sooner

than

on

dry

pavement.

•

Allow greater following distances on
slippery roads.

•

Watch for slippery spots (glare ice).
These may appear on an otherwise
clear road in shaded areas. If a patch
of ice is seen ahead, brake before
reaching it. Try not to brake while on
the ice, and avoid any sudden steer-
ing maneuvers.

•

Do not use the cruise control on slip-
pery roads.

•

Snow can trap dangerous exhaust
gases under your vehicle. Keep snow
clear of the exhaust pipe and from
around your vehicle.

ACTIVE NOISE CANCELLATION

This system uses three microphones

O

1

located inside the vehicle to detect engine
booming noises. The system then auto-
matically generates a noise canceling
sound through the speakers and woofer to
reduce engine booming noise.

LSD2637

Front and rear microphones

ACTIVE NOISE CANCELLATION/
ACTIVE SOUND CONTROL (if so
equipped)

5-124

Starting and driving

NOTE:
To operate the active noise cancella-
tion system properly:
• Do not cover the speakers or woofer.
• Do not cover the microphones.
• Do not change or modify speakers in-

cluding the woofer and any audio re-
lated

components

such

as

the

amplifier.

• Do not make any modification includ-

ing sound deadening or modifications
around the microphones, speakers, or
woofer.

ACTIVE SOUND CONTROL

Active sound control enhances existing en-
gine sounds according to the engine
speed and driving modes through the
speakers and woofer.

Starting and driving

5-125

MEMO

5-126

Starting and driving

6 In case of emergency

Hazard warning flasher switch . . . . . . . . . . . . . . . . . . 6-2
Emergency engine shut off . . . . . . . . . . . . . . . . . . . . . . 6-2
Flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3

Tire Pressure Monitoring System
(TPMS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Changing a flat tire . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4

Jump starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9

Push starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-11
If your vehicle overheats . . . . . . . . . . . . . . . . . . . . . . . . .6-11
Towing your vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12

Towing recommended by NISSAN . . . . . . . . . . . 6-12
Vehicle recovery
(freeing a stuck vehicle) . . . . . . . . . . . . . . . . . . . . . 6-13

Push the switch on to warn other drivers
when you must stop or park under emer-
gency conditions. All turn signal lights flash.

WARNING

•

If stopping for an emergency, be sure
to move the vehicle well off the road.

•

Do not use the hazard warning flash-
ers while moving on the highway un-
less unusual circumstances force
you to drive so slowly that your ve-
hicle might become a hazard to other
traffic.

•

Turn signals do not work when the
hazard warning flasher lights are on.

The flashers will operate with the ignition
switch placed in any position.

Some jurisdictions may prohibit the use
of the hazard warning flasher switch
while driving.

To shut off the engine in an emergency
situation while driving, perform the follow-
ing procedure:
– Rapidly push the push-button ignition

switch three consecutive times in less
than 1.5 seconds, or

– Push and hold the push-button ignition

switch for more than 2 seconds.

LIC0394

HAZARD WARNING FLASHER SWITCH

EMERGENCY ENGINE SHUT OFF

6-2

In case of emergency

TIRE PRESSURE MONITORING
SYSTEM (TPMS)

This vehicle is equipped with TPMS. It moni-
tors tire pressure of all tires except the
spare. When the low tire pressure warning
light is lit and the “Tire Pressure Low - Add
Air” warning appears in the vehicle infor-
mation display, one or more of your tires is
significantly under-inflated. If the vehicle is
being driven with low tire pressure, the
TPMS will activate and warn you of it by the
low tire pressure warning light. This system
will activate only when the vehicle is driven
at speeds above 16 mph (25 km/h). For ad-
ditional information, see “Warning lights, in-
dicator

lights

and

audible

reminders”

(P. 2-8) and “Tire Pressure Monitoring Sys-
tem (TPMS)” (P. 5-5).

WARNING

•

Radio waves could adversely affect
electric medical equipment. Those
who use a pacemaker should contact
the

electric

medical

equipment

manufacturer for the possible influ-
ences before use.

•

If the low tire pressure warning light
illuminates while driving, avoid sud-
den steering maneuvers or abrupt
braking, reduce vehicle speed, pull
off the road to a safe location and
stop the vehicle as soon as possible.
Driving with under-inflated tires may
permanently damage the tires and
increase the likelihood of tire failure.
Serious vehicle damage could occur
and may lead to an accident and
could result in serious personal in-
jury. Check the tire pressure for all
four tires. Adjust the tire pressure to
the recommended COLD tire pres-
sure shown on the Tire and Loading
Information label to turn the low tire
pressure warning light OFF. If the
light still illuminates while driving af-
ter adjusting the tire pressure, a tire
may be flat or the TPMS may be mal-
functioning. If you have a flat tire, re-
place it with a spare tire as soon as
possible. If no tire is flat and all tires
are properly inflated, have the ve-
hicle checked. It is recommended
that you visit a NISSAN dealer for this
service.

•

When using a wheel without the
TPMS such as the spare tire, the TPMS
will not function and the low tire
pressure warning light will flash for
approximately 1 minute. The light will
remain on after 1 minute. Have your
tires replaced and/or TPMS system
reset as soon as possible. It is recom-
mended that you visit a NISSAN
dealer for these services.

•

Replacing tires with those not origi-
nally specified by NISSAN could af-
fect the proper operation of the
TPMS.

•

Do not inject any tire liquid or aerosol
tire sealant into the tires, as this may
cause a malfunction of the tire pres-
sure sensors.

•

If the light still comes on while driving
after adjusting the tire pressure, a
tire may be flat or the TPMS may be
malfunctioning. If you have a flat tire,
replace it with a spare tire as soon as
possible. If no tire is flat and all tires
are properly inflated, it is recom-
mended that you visit a NISSAN
dealer for this service.

FLAT TIRE

In case of emergency

6-3