Nissan Murano Z51. Manual — part 1527
WT-46
< SYMPTOM DIAGNOSIS >
LOW TIRE PRESSURE WARNING LAMP BLINKS
LOW TIRE PRESSURE WARNING LAMP BLINKS
Description
INFOID:0000000005576012
DESCRIPTION
The low tire pressure warning lamp illuminates or blinks.
However, a check is necessary because the symptom may not be caused by a system malfunction. For exam-
ple, the transmitter may not be initialized.
NOTE:
If low tire pressure warning lamp blinks as shown in the figure, the system is normal.
Blink Mode A
• This mode shows transmitter status is in OFF- mode.
Perform transmitter wake up operation. Refer to
MITTER WAKE UP OPERATION : Special Repair Requirement"
.
Diagnosis Procedure
INFOID:0000000005576013
1.
CHECK TIRE PRESSURE WARNING CHECK SWITCH POWER SUPPLY
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check voltage between tire pressure warning check switch connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Riper or replace error-detected damaged parts.
2.
CHECK TIRE PRESSURE WARNING CHECK SWITCH CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect BCM harness connector.
3.
Check the continuity between BCM harness connector and tire pressure warning check switch connector.
4.
Check the continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Riper or replace error-detected damaged parts.
JPEIC0031GB
Tire pressure warning check switch
—
Voltage (Approx.)
Connector
Terminal
M19
1
Ground
11.8 V
BCM
Tire pressure warning check switch
Continuity
Connector
Terminal
Connector
Terminal
M123
149
M19
1
Existed
BCM
—
Continuity
Connector
Terminal
M123
149
Ground
Not existed
LOW TIRE PRESSURE WARNING LAMP BLINKS
WT-47
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
3.
CHECK BCM
Check the BCM input/output signal. Refer to
.
Is the inspection result normal?
YES
>> Check the tire pressure warning check switch. Refer to
.
NO
>> Repair or replace the BCM.
WT-48
< SYMPTOM DIAGNOSIS >
TURN SIGNAL LAMP BLINKS
TURN SIGNAL LAMP BLINKS
Description
INFOID:0000000005576014
DESCRIPTION
The turn signal lamp blinks when the ignition switch is turned ON.
The BCM connector or circuit may have a malfunction.
Diagnosis Procedure
INFOID:0000000005576015
1.
CHECK TIRE PRESSURE WARNING CHECK SWITCH POWER SUPPLY CIRCUIT
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check voltage between tire pressure warning check switch connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace damaged parts.
2.
CHECK TIRE PRESSURE WARNING CHECK SWITCH CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect BCM harness connector.
3.
Check the continuity between BCM harness connector and tire pressure warning check switch connector.
4.
Check the continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check the turn signal lamp operation. Refer to
BCS-35, "SIGNAL BUFFER : CONSULT-III Func-
NO
>> Repair or replace damaged parts.
Tire pressure warning check switch
—
Voltage (Approx.)
Connector
Terminal
M19
1
Ground
11.8 V
BCM
Tire pressure warning check switch
Continuity
Connector
Terminal
Connector
Terminal
Existed
M123
149
M19
1
BCM
—
Continuity
Connector
Terminal
M123
149
Ground
Not existed
ID REGISTRATION CANNOT BE COMPLETED
WT-49
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
ID REGISTRATION CANNOT BE COMPLETED
Description
INFOID:0000000005576016
DESCRIPTION
The ID of the transmitter installed in each wheel cannot be registered in the tire pressure monitoring system.
Inspect the transmitter or the tire pressure monitoring system circuit.
Diagnosis Procedure
INFOID:0000000005576017
1.
CHECK TRANSMITTER ID REGISTRATION
1.
Perform transmitter ID registration for all wheels. Refer to
WT-22, "ID REGISTRATION PROCEDURE :
2.
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
3.
Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
4.
Select “BCM” in “DATA MONITOR”, and check that the tire pressures match the standard value.
CAUTION:
Stop the vehicle and within 5 minutes, use “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”
to display the tire pressure for all wheels.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK TRANSMITTERS
1.
Perform trouble diagnosis for the transmitter. Refer to
.
2.
Perform transmitter ID registration for all wheels. Refer to
WT-22, "ID REGISTRATION PROCEDURE :
3.
Check that transmitter ID registration is completed for all wheels.
Is transmitter ID registration for all wheels been completed?
YES
>> INSPECTION END
NO
>> Replace the transmitter. Refer to
.
Monitor item
Measuring condition
Displayed value
AIR PRESS FL
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or
more, then drive normally for 10 minutes.
Internal pressure of tires
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст