Nissan Murano Z51. Manual — part 1300
DIAGNOSIS SENSOR UNIT
SR-25
< REMOVAL AND INSTALLATION >
[FOR USA AND CANADA]
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
DIAGNOSIS SENSOR UNIT
Exploded View
INFOID:0000000005518915
Removal and Installation
INFOID:0000000005518916
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative terminal and wait 3 minutes
or more.
• Before disconnecting the air bag sensor unit harness connector, be sure to disconnect the each har-
ness connector of the air bag module and pre-tensioner seat belt to prevent air bag deployment by
static electricity and pre-tensioner seat belt operation.
• Never use the air tools or electric tools for servicing.
• When replacing the air bag diagnosis sensor unit, always check with the parts department for the lat-
est parts information. Installing an incorrect air bag diagnosis sensor unit may or may not cause the
air bag warning lamp to illuminate and may cause incorrect deployment of the supplemental air bags
and seat belt pre-tensioners in a collision resulting in serious personal injury or death.
REMOVAL
1.
Always check the air bag diagnosis sensor unit ECU discriminated number (identification number) using
CONSULT-III.
2.
Disconnect the each connector of all air bag modules and pre-tensioner seat belts.
3.
Remove the instrument lower cover (LH/RH). Refer to
4.
Remove the rear foot duct 1 (LH/RH). Refer to
VTL-123, "REAR FOOT DUCT 1 : Exploded View"
5.
Remove the instrument stay LH. Refer to
6.
Remove the front console bracket. Refer to
7.
Disconnect the diagnosis sensor unit harness connectors.
8.
Remove the fixing bolts, ground bolt, and then remove the diagnosis sensor unit.
CAUTION:
1.
Diagnosis sensor unit
A.
Diagnosis sensor unit harness con-
nector
B.
Ground bolt
Refer to
for symbols in the figure.
JMHIA0517GB
SR-26
< REMOVAL AND INSTALLATION >
[FOR USA AND CANADA]
DIAGNOSIS SENSOR UNIT
• Replace the diagnosis sensor unit if it has been dropped or
sustained an impact.
• Replace the diagnosis sensor unit of deployed SRS air bag and deployed SRS front seat belt pre-ten-
sioner.
INSTALLATION
Install air bag diagnosis sensor unit in the reverse order of removal.
CAUTION:
• Never use the old fixing bolts after removal, replace with the new fixing bolts.
• If malfunction is detected by the air bag warning lamp, after repair or replacement of the malfunc-
tioning parts, reset the memory using self-diagnosis or CONSULT-III. Refer to
• After the work is completed, check that no system malfunction is detected by air bag warning lamp.
• After replacing the air bag diagnosis sensor unit, confirm using CONSULT-III that the ECU discrimi-
nated number (identification number) of the new replacement air bag sensor unit matches the ECU
discriminated number (identification number) of the replaced (old) air bag diagnosis sensor unit.
NOTE:
If the ECU discriminated number of the new replacement air bag diagnosis sensor unit differs from the ECU
discriminated number of the replaced air bag diagnosis sensor unit, reconfirm the parts information and verify
that the correct air bag diagnosis sensor unit was installed.
JMHIA0009ZZ
FRONT SEAT BELT PRE-TENSIONER
SR-27
< REMOVAL AND INSTALLATION >
[FOR USA AND CANADA]
C
D
E
F
G
I
J
K
L
M
A
B
SR
N
O
P
FRONT SEAT BELT PRE-TENSIONER
Removal and Installation
INFOID:0000000005518917
For removal and installation procedures, refer to
SB-7, "SEAT BELT RETRACTOR : Removal and Installa-
.
SR-28
< REMOVAL AND INSTALLATION >
[FOR USA AND CANADA]
OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT
OCCUPANT CLASSIFICATION SYSTEM CONTROL UNIT
Removal and Installation
INFOID:0000000005518918
For removal and installation
The occupant classification system control unit and seat sensor mat are an integral part of the front passenger
seat cushion and are replaced as an assembly. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст