Nissan Murano Z51. Manual — part 684
FRONT SIDE MARKER LAMP CIRCUIT
EXL-47
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
FRONT SIDE MARKER LAMP CIRCUIT
Component Function Check
INFOID:0000000005515054
NOTE:
Check the parking lamp circuit if the parking lamp and the front side marker lamp are not turned ON. Refer to
EXL-45, "Component Function Check"
.
1.
CHECK FRONT SIDE MARKER LAMP OPERATION
IPDM E/R AUTO ACTIVE TEST
1.
Activate IPDM E/R auto active test. Refer to
PCS-10, "Diagnosis Description"
.
2.
Check that the front side marker lamp is turned ON.
CONSULT-III ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the front side marker lamp is turned ON.
Is the front side marker lamp turned ON?
YES
>> Front side marker lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000005515055
1.
CHECK FRONT SIDE MARKER LAMP FUSE
1.
Turn the ignition switch OFF.
2.
Check that the following fuses are not fusing.
Is the fuse fusing?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK FRONT SIDE MARKER LAMP SHORT CIRCUIT
1.
Disconnect IPDM E/R connector and the front side marker lamp connector.
2.
Check continuity between the IPDM E/R harness connector and the ground.
Does continuity exist?
YES
>> Repair the harnesses or connectors. And then replace the fuse.
NO
>> Replace the fuse. (Replace IPDM E/R if fusing is found again.)
3.
CHECK FRONT SIDE MARKER LAMP BULB
Check the applicable lamp bulb.
Is the bulb normal?
YES
>> GO TO 4.
NO
>> Replace the bulb.
4.
CHECK FRONT SIDE MARKER LAMP OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1.
Disconnect the front side marker lamp connector.
TAIL
: Front side marker lamp ON
Off
: Front side marker lamp OFF
Unit
Location
Fuse No.
Capacity
Front side marker lamp
IPDM E/R
#52
10 A
IPDM E/R
Ground
Continuity
Connector
Terminal
RH
E346
91
Not existed
LH
92
EXL-48
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
FRONT SIDE MARKER LAMP CIRCUIT
2.
Turn the ignition switch ON.
3.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
4.
With operating the test items, check the voltage between the IPDM E/R harness connector and the
ground.
Is the measurement value normal?
YES
>> GO TO 5.
NO
>> Replace IPDM E/R.
5.
CHECK FRONT SIDE MARKER LAMP OPEN CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between the IPDM E/R harness connector and the front side marker lamp harness con-
nector.
Does continuity exist?
YES
>> GO TO 6.
NO
>> Repair the harnesses or connectors.
6.
CHECK FRONT SIDE MARKER LAMP GROUND OPEN CIRCUIT
Check continuity between the front side marker lamp harness connector and the ground.
Does continuity exist?
YES
>> Replace the front combination lamp.
NO
>> Repair the harnesses or connectors.
Terminals
Test item
Voltage
(Approx.)
(+)
(
−
)
IPDM E/R
Ground
EXTERNAL
LAMPS
Connector
Terminal
RH
E346
91
TAIL
Battery
voltage
Off
0 V
LH
92
TAIL
Battery
voltage
Off
0 V
IPDM E/R
Front side marker lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E346
91
E315
2
Existed
LH
92
E314
2
Front side marker lamp
Ground
Continuity
Connector
Terminal
RH
E315
1
Existed
LH
E314
1
TURN SIGNAL LAMP CIRCUIT
EXL-49
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
TURN SIGNAL LAMP CIRCUIT
Description
INFOID:0000000005515056
BCM performs the high flasher operation (fail-safe) if any bulb or harness of the turn signal lamp circuit is
open.
NOTE:
The turn signal lamp blinks at normal speed when using the hazard warning lamp.
Component Function Check
INFOID:0000000005515057
1.
CHECK TURN SIGNAL LAMP
CONSULT-III ACTIVE TEST
1.
Select “FLASHER” of BCM (FLASHER) active test item.
2.
With operating the test items, check that the turn signal lamp is turned ON.
Is the turn signal lamp turned ON?
YES
>> Turn signal lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000005515058
1.
CHECK TURN SIGNAL LAMP BULB
Check the applicable lamp bulb.
Is the bulb normal?
YES
>> GO TO 2.
NO
>> Replace the bulb.
2.
CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE
1.
Turn the ignition switch OFF.
2.
Disconnect the front turn signal lamp connector or the rear combination lamp connector.
3.
Turn the ignition switch ON.
4.
With operating the turn signal switch, check the voltage between the BCM harness connector and the
ground.
LH
: Turn signal lamps (LH) ON
RH
: Turn signal lamps (RH) ON
Off
: Turn signal lamps OFF
EXL-50
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
TURN SIGNAL LAMP CIRCUIT
Is the measurement value normal?
YES
>> GO TO 3.
NO
>> Replace BCM. Refer to
3.
CHECK TURN SIGNAL LAMP OPEN CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between the BCM harness connector and the front turn signal lamp or the rear combina-
tion lamp harness connector.
Front turn signal lamp
Rear turn signal lamp
Does continuity exist?
YES
>> GO TO 4.
NO
>> Repair the harnesses or connectors.
4.
CHECK TURN SIGNAL LAMP SHORT CIRCUIT
Check continuity between the BCM harness connector and the ground.
Terminals
Condition
Voltage (Approx.)
(+)
(
−
)
BCM
Ground
Turn signal
switch
Connector
Terminal
RH
M119
17
RH
OFF
0 V
LH
18
LH
OFF
0 V
PKID0926E
PKID0926E
BCM
Front turn signal lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
M119
17
E328
1
Existed
LH
18
E327
BCM
Rear combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
M119
17
B59
2
Existed
LH
18
B80
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст