Nissan Murano Z51. Manual — part 820
GW-24
< REMOVAL AND INSTALLATION >
FRONT REGULATOR
FITTING INSPECTION
• Check that the glass is fit securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass and guide rail
mounting bolts to correct the glass position if the clearance between the glass and sash is not parallel.
REAR DOOR GLASS
GW-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REAR DOOR GLASS
Exploded View
INFOID:0000000005513270
Removal and Installation
INFOID:0000000005513271
REMOVAL
1.
Remove the rear door finisher. Refer to
INT-20, "Removal and Installation"
.
2.
Disconnect the rear door speaker connector.
3.
Remove the rear door outside sash cover. Refer to
EXT-40, "Removal and Installation"
4.
Remove partially the rear door glass run.
5.
Remove the corner piece assembly fixing screws, then remove the corner piece assembly.
6.
Remove the rear door inside seal
7.
Remove the sealing screen with a cutter tool.
1.
Rear door panel
2.
Rear door glass run
3.
Rear door sash (lower)
4.
Corner piece
5.
Rear door glass
6.
Power window motor
7.
Regulator assembly
8.
Rear door inside seal
9.
Sealing screen
: Vehicle front
JMKIA3605ZZ
JMKIA0631ZZ
GW-26
< REMOVAL AND INSTALLATION >
REAR DOOR GLASS
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
8.
Operate the power window switch to raise/lower the door win-
dow until the glass mounting bolts can be seen.
9.
Remove the glass mounting bolts.
10. Remove the rear door glass from inside or outside of door panel.
11. Remove the rear door glass run and rear door sash (lower).
INSTALLATION
Install in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000005513272
FITTING INSPECTION
• Check that the glass is fit securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. Loosen the regulator mounting bolts, guide rail mounting bolts, and glass and carrier plate
mounting bolts to correct the glass position if the clearance between the glass and sash is not parallel.
: Bolt
JMKIA1789ZZ
JMKIA0640ZZ
REAR REGULATOR
GW-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REAR REGULATOR
Exploded View
INFOID:0000000005513273
Removal and Installation
INFOID:0000000005513274
REMOVAL
1.
Remove the rear door glass. Refer to
GW-25, "Removal and Installation"
2.
Disconnect the connector for the regulator assembly.
3.
Remove the regulator mounting bolts, disconnect the power win-
dow motor harness connector (A) and then remove the regulator
from the door panel.
INSTALLATION
Install in the reverse order of removal.
1.
Rear door panel
2.
Rear door glass run
3.
Rear door sash (lower)
4.
Corner piece
5.
Rear door glass
6.
Power window motor
7.
Regulator assembly
8.
Rear door inside seal
9.
Sealing screen
: Vehicle front
JMKIA3605ZZ
: Bolt
JMKIA1790ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст