Nissan Murano Z51. Manual — part 459
DLK-344
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
10. While pulling outside handle bracket, slide toward rear of vehicle
to remove outside handle bracket.
11. Reach in to separate outside handle cable connection on outside handle bracket.
12. Remove door lock assembly TORX bolts.
13. Disconnect door lock actuator connector, and then remove door lock assembly.
14. Remove key rod from door lock assembly.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• To install each rod, rotate rod holder until a click is felt.
• Check door open/close, lock/unlock operation after installation.
INSIDE HANDLE
INSIDE HANDLE : Exploded View
INFOID:0000000005517813
PIIB5814E
1.
TORX bolt
2.
Key rod
3.
Door lock assembly
4.
Inside handle
5.
Front gasket
6.
Outside handle
7.
Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)
8.
Rear gasket
9.
Outside handle bracket
JMKIA1802GB
FRONT DOOR LOCK
DLK-345
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
INSIDE HANDLE : Removal and Installation
INFOID:0000000005517814
REMOVAL
1.
Remove front door finisher. Refer to
INT-12, "FRONT DOOR FINISHER : Removal and Installation"
.
2.
Remove inside handle mounting screws.
3.
Disconnect inside handle cable, and then remove the inside handle.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check door open/close, lock/unlock operation after installation.
OUTSIDE HANDLE
OUTSIDE HANDLE : Exploded View
INFOID:0000000005517815
:Vehicle front
: Apply genuine high strength thread locking sealant or equivalent.
Refer to
for symbols in the figure.
1.
TORX bolt
2.
Key rod
3.
Door lock assembly
4.
Inside handle
5.
Front gasket
6.
Outside handle
7.
Door key cylinder assembly (driver
side)
Outside handle escutcheon (passen-
ger side)
8.
Rear gasket
9.
Outside handle bracket
:Vehicle front
: Apply genuine high strength thread locking sealant or equivalent.
Refer to
for symbols in the figure.
JMKIA1802GB
DLK-346
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
FRONT DOOR LOCK
OUTSIDE HANDLE : Removal and Installation
INFOID:0000000005517816
REMOVAL
1.
Remove front door finisher. Refer to
INT-12, "FRONT DOOR FINISHER : Removal and Installation"
.
2.
Remove front door glass. Refer to
GW-19, "Removal and Installation"
3.
Remove front door module assembly. Refer to
GW-19, "Removal and Installation"
.
4.
Disconnect door antenna and door request switch connector and remove harness clamp (models with
Intelligent Key system) on outside handle bracket.
5.
Remove door side grommet, and loosen TORX bolt from grom-
met hole.
CAUTION:
Never forcibly remove TORX bolt.
6.
Reach in to separate door key rod connection (on the handle)
(driver side).
7.
While pulling outside handle, remove door key cylinder assem-
bly (diver side) or outside handle escutcheon (passenger side).
8.
While pulling outside handle (1), slide toward rear of vehicle to
remove outside handle.
9.
Remove front gasket and rear gasket.
JMKIA0020ZZ
1.
Door key cylinder assembly
2.
Key rod
JMKIA0553ZZ
JMKIA0560ZZ
JMKIA0524ZZ
FRONT DOOR LOCK
DLK-347
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
10. While pulling outside handle bracket, slide toward rear of vehicle
to remove outside handle bracket.
11. Reach in to separate outside handle cable connection on outside handle bracket.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• To install each rod, rotate rod holder until a click is felt.
• Check door open/close, lock/unlock operation after installation.
PIIB5814E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст