Nissan Murano Z51. Manual — part 1195
RSU-4
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000005514342
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0190E
REAR SUSPENSION ASSEMBLY
RSU-5
< PERIODIC MAINTENANCE >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
PERIODIC MAINTENANCE
REAR SUSPENSION ASSEMBLY
Inspection
INFOID:0000000005514343
MOUNTING INSPECTION
Make sure the mounting conditions (looseness, backlash) of each component and component conditions
(wear, damage) are normal.
BALL JOINT AXIAL END PLAY
1.
Set rear wheels in a straight-ahead position.
2.
Measure axial end play by prying it up/down with iron bar or equivalent between transverse link and steer-
ing knuckle.
CAUTION:
• Never depress brake pedal when measuring.
• Never perform with tires on level ground.
• Be careful not to damage ball joint boot. Never damage the installation position by applying
excessive force.
SHOCK ABSORBER ASSEMBLY
Check for oil leakage, damage, and replace if necessary.
Axial end play
: Refer to
.
RSU-6
< PERIODIC MAINTENANCE >
WHEEL ALIGNMENT
WHEEL ALIGNMENT
Inspection
INFOID:0000000005514344
DESCRIPTION
Measure wheel alignment under unladen conditions.
NOTE:
“Unladen conditions” means that fuel, engine coolant, and lubricant are full. Spare tire, jack, hand tools and
mats are in designated positions.
PRELIMINARY CHECK
Check the following:
• Tires for improper air pressure and wear.
• Road wheels for runout. Refer to
• Wheel bearing axial end play. Refer to
(AWD).
• Shock absorber operation.
• Each mounting point of axle and suspension for looseness and deformation.
• Each of front lower link, rear lower link, radius rod, rear suspension member, suspension arm and shock
absorber for cracks, deformation, and other damage.
• Vehicle height (posture).
GENERAL INFORMATION AND RECOMMENDATIONS
• A four-wheel thrust alignment should be performed.
- This type of alignment is recommended for any NISSAN/INFINITI vehicle.
- The four-wheel “thrust” process helps ensure that the vehicle is properly aligned and the steering wheel is
centered.
- The alignment rack itself should be capable of accepting any NISSAN/INFINITI vehicle.
- The rack should be checked to ensure that it is level.
• Make sure the machine is properly calibrated.
- Your alignment equipment should be regularly calibrated in order to give correct information.
- Check with the manufacturer of your specific equipment for their recommended Service/Calibration Sched-
ule.
ALIGNMENT PROCESS
IMPORTANT:
Use only the alignment specifications listed in this Service Manual.
• When displaying the alignment settings, many alignment machines use “indicators”: (Green/red, plus or
minus, Go/No Go). Never use these indicators.
- The alignment specifications programmed into your machine that operate these indicators may not be cor-
rect.
- This may result in an ERROR.
• Some newer alignment machines are equipped with an optional “Rolling Compensation” method to “com-
pensate” the sensors (alignment targets or head units). Never use this “Rolling Compensation” method.
- Use the “Jacking Compensation Method”. After installing the alignment targets or head units, raise the vehi-
cle and rotate the wheels 1/2 turn both ways.
- See Instructions in the alignment machine you're using for more information on this.
Adjustment
INFOID:0000000005514345
CAMBER
• If camber is exceeds the standard value, adjust with adjusting bolt
(1) in front lower link (2).
CAUTION:
After adjusting camber, be sure to check toe-in.
- If camber is not still within the specification, inspect and replace
any damaged or worn suspension parts.
Camber: Refer to
.
JPEIB0080ZZ
WHEEL ALIGNMENT
RSU-7
< PERIODIC MAINTENANCE >
C
D
F
G
H
I
J
K
L
M
A
B
RSU
N
O
P
TOE-IN
• If toe-in is exceeds the standard value, adjust with adjusting bolt
(1) in rear lower link (2).
CAUTION:
• Be sure to adjust equally on right and left side with adjust-
ing bolt.
• When tightening the nut firmly and checking the torque, use
a wrench to prevent the turning of the bolt.
- If toe-in is not still within the specification, inspect and replace any
damaged or worn suspension parts.
Toe-In: Refer to
JPEIB0081ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст