Nissan Murano Z51. Manual — part 717
FRONT COMBINATION LAMP
EXL-179
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REMOVAL AND INSTALLATION
FRONT COMBINATION LAMP
Exploded View
INFOID:0000000005515105
REMOVAL
DISASSEMBLY
1.
Front combination lamp
2.
Headlamp extension panel
JPLIA0812ZZ
1.
Front side marker lamp bulb
2.
Front side marker lamp bulb socket
3.
Resin cap
4.
Seal packing
5.
Xenon bulb socket (Starter)
6.
Xenon bulb
7.
Retaining spring
8.
Seal packing
9.
HID control unit (Inverter)
10.
Parking lamp bulb socket
11. Parking lamp bulb
12. Front turn signal lamp bulb socket
13.
Front turn signal lamp bulb
14. Headlamp housing assembly
for symbols in the figure.
JPLIA0813ZZ
EXL-180
< REMOVAL AND INSTALLATION >
[XENON TYPE]
FRONT COMBINATION LAMP
Removal and Installation
INFOID:0000000005515106
REMOVAL
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
1.
Remove the front grille. Refer to
2.
Remove the headlamp extension panel.
3.
Remove the front bumper fascia. Refer to
.
4.
Remove the headlamp mounting bolts.
5.
Remove the harness clips from headlamp housing assembly.
6.
Pull out the headlamp assembly forward the vehicle.
7.
Disconnect the connector before removing the headlamp assembly.
INSTALLATION
Install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
Replacement
INFOID:0000000005515107
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
HEADLAMP BULB
1.
Remove the fender rubber protector in engine room.
2.
Rotate the resin cap counterclockwise and unlock it.
3.
Rotate the bulb socket counterclockwise and unlock it.
4.
Unlock the retaining spring. And then remove the bulb from the
headlamp housing assembly.
CAUTION:
Never break the xenon bulb ceramic tube when replacing
the bulb.
PARKING LAMP BULB
1.
Rotate the bulb socket counterclockwise and unlock it.
2.
Remove the bulb from the bulb socket.
FRONT TURN SIGNAL LAMP BULB
1.
Remove the front grille.
2.
Rotate the bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the bulb socket.
FRONT SIDE MARKER LAMP BULB
1.
Remove the fender rubber protector in engine room.
2.
Rotate the bulb socket counterclockwise and unlock it.
3.
Remove the bulb from the bulb socket.
JPLIA0814ZZ
FRONT COMBINATION LAMP
EXL-181
< REMOVAL AND INSTALLATION >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Disassembly and Assembly
INFOID:0000000005515108
DISASSEMBLY
1.
Rotate the resin cap counterclockwise and unlock it.
2.
Rotate the xenon bulb socket counterclockwise and unlock it.
3.
Unlock the retaining spring. And then remove the xenon bulb.
4.
Remove the HID control unit installation screw.
5.
Remove the screw. And then disconnect the connector from HID control unit.
6.
Remove the xenon bulb socket from headlamp housing assembly.
7.
Rotate the parking lamp bulb socket counterclockwise and unlock it.
8.
Remove the bulb from parking lamp bulb socket.
9.
Rotate the front turn signal lamp bulb socket counterclockwise and unlock it.
10. Remove the bulb from front turn signal lamp bulb socket.
11. Rotate the front side marker lamp bulb socket counterclockwise and unlock it.
12. Remove the bulb from front side marker lamp bulb socket.
ASSEMBLY
Assemble in the reverse order of disassembly.
CAUTION:
• Install HID control unit securely.
• After installing the bulb, install the resin cap and the bulb socket securely for watertightness.
EXL-182
< REMOVAL AND INSTALLATION >
[XENON TYPE]
FRONT FOG LAMP
FRONT FOG LAMP
Exploded View
INFOID:0000000005515109
Removal and Installation
INFOID:0000000005515110
CAUTION:
Disconnect the battery negative terminal or remove the fuse.
REMOVAL
1.
Remove the front fender protector. Keep a service area. Refer to
.
2.
Remove the front fog lamp connector.
3.
Remove the screw.
4.
Disengage the pawl. And then remove the front fog lamp.
INSTALLATION
Installation is the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
Replacement
INFOID:0000000005515111
CAUTION:
• Disconnect the battery negative terminal or remove the fuse.
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
• Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
FRONT FOG LAMP BULB
1.
Remove the front fender protector. Keep the service area. Refer to
.
1.
Front fog lamp
: Pawl
JPLIA1592ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст