Nissan Murano Z51. Manual — part 1074
PCS-38
< BASIC INSPECTION >
[POWER DISTRIBUTION SYSTEM]
DIAGNOSIS AND REPAIR WORK FLOW
Is malfunctioning part detected?
YES
>> GO TO 8.
NO
>> Check voltage of related BCM terminals using CONSULT-III.
8.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1.
Repair or replace the malfunctioning part.
2.
Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment.
3.
Check DTC. If DTC is detected, erase it.
>> GO TO 9.
9.
FINAL CHECK
When DTC was detected in step 2, perform DTC Confirmation Procedure or Component Function Check
again, and then check that the malfunction has been repaired securely.
When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
Does the symptom reappear?
YES (DTC is detected)>>GO TO 7.
YES (Symptom remains)>>GO TO 6.
NO
>> INSPECTION END
PCS
POWER DISTRIBUTION SYSTEM
PCS-39
< SYSTEM DESCRIPTION >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SYSTEM DESCRIPTION
POWER DISTRIBUTION SYSTEM
System Description
INFOID:0000000005516960
SYSTEM DESCRIPTION
• PDS (POWER DISTRIBUTION SYSTEM) is the system that BCM controls with the operation of the push-
button ignition switch and performs the power distribution to each power circuit. This system is used instead
of the mechanical power supply changing mechanism with the operation of the conventional key cylinder.
• The push-button ignition switch can be operated when Intelligent Key is in the following condition. Refer to
Engine Start Function for details.
- Intelligent Key is in the detection area of the inside key antenna
- Insert Intelligent Key into the key slot
- Insert keyfob into the key slot
• The push-button ignition switch operation is input to BCM as a signal. BCM changes the power supply posi-
tion according to the status and operates the following relays to supply power to each power circuit.
- Ignition relay (inside IPDM E/R)
- Ignition relay (inside fuse block)
- ACC relay
- Blower relay
NOTE:
The engine switch operation changes due to the conditions of brake pedal, selector lever and vehicle speed.
• The power supply position can be confirmed with the lighting of the indicators around the push-button igni-
tion switch.
BATTERY SAVER SYSTEM
When all the following conditions are met for 60 minutes, the battery saver system will cut off the power supply
to prevent battery discharge.
• The ignition switch is in the ACC position
• All doors are closed
• Selector lever is in the P position
Reset Condition of Battery Saver System
In order to prevent the battery from discharging, the battery saver system will cut off the power supply when all
doors are closed, the selector lever is on P position and the ignition switch is left on ACC position for 60 min-
utes. If any of the following conditions are met the battery saver system is released and the steering will
change automatically to lock position from OFF position.
• Opening any door
• Operating with door key cylinder on door lock
• Operating with door request switch on door lock
• Operating with Intelligent Key on door lock
Press push-button ignition switch and ignition switch will change to ACC position from OFF position.
STEERING LOCK OPERATION
NOTE:
Even if the steering lock unit is not equipped, power supply position changes to LOCK in the same condition.
Steering is locked by steering lock unit when ignition switch is in the OFF position, selector lever is in the P
position and any of the following conditions are met.
• Opening door
• Closing door
• Door is locked with request switch
• Door is locked with Intelligent Key
POWER SUPPLY POSITION CHANGE TABLE BY PUSH-BUTTON IGNITION SWITCH OPERA-
TION
The power supply position changing operation can be performed with the following operations.
NOTE:
• When an Intelligent Key is within the detection area of inside key antenna and when it is inserted to the key
slot, it is equivalent to the operations below.
• When starting the engine, the BCM checks the following conditions and then changes the power supply
position.
PCS-40
< SYSTEM DESCRIPTION >
[POWER DISTRIBUTION SYSTEM]
POWER DISTRIBUTION SYSTEM
- Brake pedal operating condition
- Selector lever position
- Vehicle speed
Vehicle speed: less than 4 km/h (2.5 MPH)
Vehicle speed: 4 km/h (2.5 MPH) or more
Emergency stop operation
• Press and hold the push-button ignition switch for 2 seconds or more.
• Press the push-button ignition switch 3 times or more within 1.5 seconds.
Component Parts Location
INFOID:0000000005516961
Power supply position
Engine start/stop condition
Push-button ignition switch
operation frequency
Selector lever
Brake pedal operation condi-
tion
LOCK
→
ACC
—
Not depressed
1
LOCK
→
ACC
→
ON
—
Not depressed
2
LOCK
→
ACC
→
ON
→
OFF
—
Not depressed
3
LOCK
→
START
ACC
→
START
ON
→
START
P or N position
Depressed
1
Engine is running
→
OFF
—
—
1
Power supply position
Engine start/stop condition
Push-button ignition switch
operation frequency
Selector lever
Brake pedal operation condi-
tion
Engine is running
→
ACC
—
—
Emergency stop operation
Engine stall return operation while
driving
N position
Not depressed
1
JMMIA0009ZZ
PCS
POWER DISTRIBUTION SYSTEM
PCS-41
< SYSTEM DESCRIPTION >
[POWER DISTRIBUTION SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
Component Description
INFOID:0000000005516962
1.
BCM M118, M119, M121, M122, M123 2.
TCM F23
3.
IPDM E/R E10, E11, F12
4.
Push-button ignition switch M101
5.
Combination meter (Key warning
lamp) M34
6.
Stop lamp switch
E115 (TYPE A)
E116 (TYPE B)
A.
Behind the combination meter
B.
Engine room dash panel (LH)
C.
Behind the instrument lower panel LH
Component
Reference
IPDM E/R
Ignition relay (built into IPDM E/R)
Ignition relay (inserted into fuse block)
Accessory relay
Blower relay
Stop lamp switch
Transmission range switch
Push-button ignition switch
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст