Nissan Murano Z51. Manual — part 593
EC-380
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
P1574 ASCD VEHICLE SPEED SENSOR
P1574 ASCD VEHICLE SPEED SENSOR
Description
INFOID:0000000005536788
The ECM receives two vehicle speed signals via CAN communication line. One is sent from combination
meter, and the other is from TCM (Transmission control module). The ECM uses these signals for ASCD con-
trol. Refer to
for ASCD functions.
DTC Logic
INFOID:0000000005536789
DTC DETECTION LOGIC
NOTE:
• If DTC P1574 is displayed with DTC UXXXX, first perform the trouble diagnosis for DTC UXXXX.
• If DTC P1574 is displayed with DTC P0500, first perform the trouble diagnosis for DTC P0500. Refer
• If DTC P1574 is displayed with DTC P0605, first perform the trouble diagnosis for DTC P0605. Refer
• If DTC P1574 is displayed with DTC P0607, first perform the trouble diagnosis for DTC P0607. Refer
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine (VDC switch OFF).
2.
Drive the vehicle at more than 40 km/h (25 MPH).
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
This procedure may be conducted with the drive wheels lifted in the shop or by driving the vehicle.
If a road test is expected to be easier, it is unnecessary to lift the vehicle.
3.
Check DTC.
Is DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000005536790
1.
CHECK DTC WITH TCM
Check DTC with TCM. Refer to
TM-34, "Diagnosis Description"
.
Is the inspection result normal?
DTC No.
Trouble diagnosis
name
DTC detecting condition
Possible cause
P1574
ASCD vehicle speed
sensor
The difference the between two vehicle speed
signals is out of the specified range.
• Harness or connectors
(The CAN communication line is open or
shorted.)
• Combination meter
• ABS actuator and electric unit (control unit)
• Wheel sensor
• TCM
• ECM
P1574 ASCD VEHICLE SPEED SENSOR
EC-381
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
YES
>> GO TO 2.
NO
>> Perform trouble shooting relevant to DTC indicated.
2.
CHECK DTC WITH “ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)”
BRC-28, "CONSULT-III Function"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning part.
3.
CHECK COMBINATION METER FUNCTION
MWI-34, "CONSULT-III Function (METER/M&A)"
.
>> INSPECTION END
EC-382
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
P1700 CVT CONTROL SYSTEM
P1700 CVT CONTROL SYSTEM
Description
INFOID:0000000005536791
This DTC is displayed with other DTC regarding TCM. Perform the trouble diagnosis for corresponding DTC.
Refer to
. When this DTC is detected, the ASCD control is canceled.
P1715 INPUT SPEED SENSOR (PRIMARY SPEED SENSOR)
EC-383
< DTC/CIRCUIT DIAGNOSIS >
[VQ35DE]
C
D
E
F
G
H
I
J
K
L
M
A
EC
N
P
O
P1715 INPUT SPEED SENSOR (PRIMARY SPEED SENSOR)
Description
INFOID:0000000005536792
ECM receives input speed sensor signal from TCM via the CAN communication line. ECM uses this signal for
engine control.
DTC Logic
INFOID:0000000005536793
DTC DETECTION LOGIC
NOTE:
• If DTC P1715 is displayed with DTC UXXXX first perform the trouble diagnosis for DTC UXXXX.
• If DTC P1715 is displayed with DTC P0335, first perform the trouble diagnosis for DTC P0335. Refer
.
• If DTC P1715 is displayed with DTC P0340, P0345, first perform the trouble diagnosis for DTC P0340,
P0345. Refer to
.
• If DTC P1715 is displayed with DTC P0605, first perform the trouble diagnosis for DTC P0605. Refer
.
• If DTC P1715 is displayed with DTC P0607, first perform the trouble diagnosis for DTC P0607. Refer
.
DTC CONFIRMATION PROCEDURE
1.
PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1.
Turn ignition switch OFF and wait at least 10 seconds.
2.
Turn ignition switch ON.
3.
Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Start engine.
2.
Drive vehicle at a speed of more than 50 km/h (31 MPH) for at least 5 seconds.
3.
Check 1st trip DTC.
Is 1st trip DTC detected?
YES
>> Go to
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000005536794
1.
CHECK DTC WITH TCM
Check DTC with TCM. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Perform trouble shooting relevant to DTC indicated.
2.
REPLACE TCM
Replace TCM. Refer to
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
P1715
Input speed sensor
(TCM output)
Input speed sensor signal is different from
the theoretical value calculated by ECM
from output speed sensor signal and en-
gine rpm signal.
• Harness or connectors
(The CAN communication line is open or short-
ed)
• Harness or connectors
(Input speed sensor circuit is open or shorted)
• TCM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст