Nissan Murano Z51. Manual — part 1160
RAX-2
< SYMPTOM DIAGNOSIS >
[2WD]
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
SYMPTOM DIAGNOSIS
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000005514281
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference page
—
NVH in RAX and RSU sections
NVH in WT
section
NVH in WT
section
NVH in BR
section
Possible cause and SUSPECTED PARTS
Im
pro
per in
st
a
lla
ti
on
,
lo
os
en
es
s
Part
s int
e
rference
Whe
e
l be
ari
n
g
da
m
age
REAR AXLE AND RE
AR SUSPENSI
ON
TIRE
ROA
D
WHEEL
BRAKE
Symptom
REAR AXLE
Noise
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
Shimmy
×
×
×
×
×
×
Judder
×
×
×
×
×
Poor quality ride or handling
×
×
×
×
×
PREPARATION
RAX-3
< PREPARATION >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000005514282
Tool name
Description
Power tool
Loosening bolts and nuts
PBIC0190E
RAX-4
< PERIODIC MAINTENANCE >
[2WD]
REAR WHEEL HUB AND HOUSING
PERIODIC MAINTENANCE
REAR WHEEL HUB AND HOUSING
Inspection
INFOID:0000000005514283
MOUNTING INSPECTION
Make sure the mounting conditions (looseness, back lash) of each component and component conditions
(wear, damage) are normal.
WHEEL BEARING INSPECTION
• Move wheel hub and bearing assembly in the axial direction by hand. Make sure there is no looseness of
wheel bearing.
• Rotate wheel hub and bearing assembly and make sure there is no unusual noise or other irregular condi-
tions. If there is any of irregular conditions, replace wheel hub and bearing assembly.
Standard
Axial end play
: Refer to
.
REAR WHEEL HUB AND HOUSING
RAX-5
< REMOVAL AND INSTALLATION >
[2WD]
C
E
F
G
H
I
J
K
L
M
A
B
RAX
N
O
P
REMOVAL AND INSTALLATION
REAR WHEEL HUB AND HOUSING
Exploded View
INFOID:0000000005514284
Removal and Installation
INFOID:0000000005514285
REMOVAL
1.
Remove tire with power tool.
2.
Remove wheel sensor and sensor harness. Refer to
BRC-111, "REAR WHEEL SENSOR : Exploded
.
3.
Remove caliper assembly. Hang caliper assembly in a place where it will not interfere with work. Refer to
BR-42, "BRAKE CALIPER ASSEMBLY : Exploded View"
CAUTION:
Never depress brake pedal while caliper assembly is removed.
4.
Remove disc rotor. Refer to
BR-43, "BRAKE CALIPER ASSEMBLY : Removal and Installation"
.
5.
Remove cotter pin, then loosen suspension arm mounting nut of axle housing. Refer to
6.
Remove wheel hub and bearing assembly.
7.
Remove parking brake shoe and parking brake cable from back plate. Refer to
8.
Remove anchor block mounting nuts, and then remove anchor block and back plate from axle housing.
9.
Remove stabilizer connecting rod (upper side) with power tool. Refer to
.
10. Remove radius rod (axle housing side). Refer to
11. Remove coil spring. Refer to
12. Set suitable jack under axle housing.
13. Remove front lower link (shock absorber side) with power tool. Refer to
14. Remove front lower link (axle housing side). Refer to
.
15. Separate suspension arm from axle housing so as not to damage ball joint boot using ball joint remover,
and then remove axle housing from the vehicle.
1.
Ball seat
2.
Bushing
3.
Cotter pin
4.
Axle housing
5.
Back plate
6.
Anchor block
7.
Wheel hub and bearing assembly
Refer to
JPDIG0095GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст