Nissan Murano Z51. Manual — part 468
DLN-6
< SYSTEM DESCRIPTION >
[TRANSFER: TY20A]
AWD SYSTEM
System Description
INFOID:0000000005514145
DESCRIPTION
• AWD controls distribution of drive power between front-wheel drive (100:0) and 4-wheel drive (50:50) condi-
tions according to signals from sensors.
• By receiving the steering angle sensor signal, yaw rate sensor signal, side G sensor signal and decel G sen-
sor signal, vehicle with VDC corrects a torque distribution for front and rear wheels according to a driving
operation and a behavior of the vehicle during cornering and improves drivability and safety on a slippery
road surface.
• It transmits/receives each signal from the following AWD control unit via CAN communication line.
1.
Adapter case
2.
Transfer case
3.
Gear ring bearing (Transfer case side)
4.
Pinion front bearing
5.
Pinion sleeve
6.
Drive pinion
7.
Companion flange
8.
Pinion rear bearing
9.
Drive gear
10. Gear ring bearing (Adapter case side)
JPDIE0015ZZ
Component parts
Function
ABS actuator and electric unit (control unit)
Transmits the following signals via CAN communication to AWD control unit.
• Vehicle speed signal
• Stop lamp switch signal (brake signal)
• Yaw rate sensor signal
• Side G sensor signal
• Decel G sensor signal
ECM
Transmits the following signals via CAN communication to AWD control unit.
• Accelerator pedal position signal
• Engine speed signal
AWD SYSTEM
DLN-7
< SYSTEM DESCRIPTION >
[TRANSFER: TY20A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
AUTO Mode
• Electronic control allows optimal distribution of torque to front/rear wheels to match road conditions.
• AWD mode makes possible stable driving possible with no wheel spin, on snowy roads or other slippery sur-
faces.
• On roads which do not require 4-wheel drive, AUTO mode contributes to improved fuel economy by driving
in conditions close to front-wheel drive.
• Sensor inputs determine the vehicle's turning condition, and tight cornering/braking are controlled by distrib-
uting optimum torque to rear wheels.
NOTE:
Light tight-corner braking symptom may occur depending on driving condition in AUTO mode. This is not mal-
function.
LOCK Mode
• Front/rear wheel torque distribution is fixed, ensuring stable driving when climbing slopes.
• Vehicle will switch automatically to AUTO mode if vehicle speed increases. If vehicle speed then decreases,
the vehicle automatically returns to direct 4-wheel driving conditions. The AWD LOCK indicator lamp keeps
illuminating.
• LOCK mode will change to AUTO mode automatically, when the vehicle has been driven at a high speed.
The AWD LOCK indicator lamp turns off.
• LOCK mode will change to AUTO mode automatically, when the ignition switch is turned “OFF”.
NOTE:
• Every time AWD LOCK switch is pressed, AUTO mode and LOCK mode switch each other.
• If there is a significant difference in pressure or wear between tires, full vehicle performance is not available.
Tire conditions are detected, and LOCK mode may be prohibited, or else speeds at which LOCK mode is
enabled may be restricted.
• Heavy tight-corner braking symptom occurs when vehicle is driven in the following conditions: LOCK mode,
steering wheel is turned fully to either sides, and accelerator pedal is depressed.
CAUTION:
Never switch to LOCK when rotation speed of front and rear wheel differs.
POWER TRANSFER DIAGRAM
OPERATION PRINCIPLE
Electric Controlled Coupling
Combination meter
Transmits conditions of parking brake switch signal via CAN communication to AWD con-
trol unit.
Receives the following signals via CAN communication from AWD control unit.
• AWD warning lamp signal
• AWD LOCK indicator lamp signal
Steering angle sensor
Transmits conditions of steering angle sensor signal via CAN communication to AWD
control unit.
Component parts
Function
SDIA1607E
DLN-8
< SYSTEM DESCRIPTION >
[TRANSFER: TY20A]
AWD SYSTEM
1.
The AWD control unit supplies command current to electric con-
trolled coupling (AWD solenoid).
2.
The control clutch is engaged by electromagnet and torque is
detected in control clutch.
3.
The cam operates in response to control clutch torque and
applies pressure to main clutch.
4.
The main clutch transmits torque to front wheels according to
pressing power.
• Transmission torque to the rear wheels is determined accord-
ing to command current.
Component Parts Location
INFOID:0000000005514146
SDIA2035E
SDIA1844E
1.
AWD LOCK indicator lamp
2.
AWD warning lamp
3.
AWD lock switch
4.
AWD control unit
5.
AWD solenoid (in rear final drive)
A.
Combination meter
B.
Center console (Front side)
C.
Instrument driver lower cover removed
D.
Rear final drive assembly
JPDIE0052ZZ
AWD SYSTEM
DLN-9
< SYSTEM DESCRIPTION >
[TRANSFER: TY20A]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
Component Description
INFOID:0000000005514147
Component parts
Reference/Function
AWD control unit
Wheel sensors
AWD solenoid
Electric controlled coupling
Transmits driving force to rear final drive.
AWD warning lamp
AWD LOCK indicator lamp
AWD lock switch
ABS actuator and electric unit (control unit)
ECM
Combination meter
Steering angle sensor
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст