Nissan Murano Z51. Manual — part 681
EXTERIOR LAMP FUSE
EXL-35
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
EXTERIOR LAMP FUSE
Description
INFOID:0000000005515040
Fuse list
Diagnosis Procedure
INFOID:0000000005515041
1.
CHECK FUSE
Check that the following fuses are not fusing.
Is the fuse fusing?
YES
>> Repair the applicable circuit. And then replace the fuse.
NO
>> The fuse is normal.
Unit
Location
Fuse No.
Capacity
Headlamp HI (LH)
IPDM E/R
#54
10 A
Headlamp HI (RH)
IPDM E/R
#55
10 A
Headlamp LO (LH)
IPDM E/R
#56
15 A
Headlamp LO (RH)
IPDM E/R
#57
15 A
Front fog lamp
IPDM E/R
#58
15 A
• Parking lamp
• Front side marker lamp
IPDM E/R
#52
10 A
• Tail lamp
• Rear side marker lamp
• License plate lamp
• Each illumination
IPDM E/R
#53
10 A
Stop lamp
FUSE BLOCK (J/B)
#7
10 A
Back-up lamp
FUSE BLOCK (J/B)
#4
10 A
Unit
Location
Fuse No.
Capacity
Headlamp HI (LH)
IPDM E/R
#54
10 A
Headlamp HI (RH)
IPDM E/R
#55
10 A
Headlamp LO (LH)
IPDM E/R
#56
15 A
Headlamp LO (RH)
IPDM E/R
#57
15 A
Front fog lamp
IPDM E/R
#58
15 A
• Parking lamp
• Front side marker lamp
IPDM E/R
#52
10 A
• Tail lamp
• Rear side marker lamp
• License plate lamp
• Each illumination
IPDM E/R
#53
10 A
Stop lamp
FUSE
BLOCK (J/B)
#7
10 A
Back-up lamp
FUSE
BLOCK (J/B)
#4
10 A
EXL-36
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
HEADLAMP (HI) CIRCUIT
HEADLAMP (HI) CIRCUIT
Description
INFOID:0000000005515042
The high beam solenoid drives the mobile valve shade. And the mobile valve shade switches the high beam
and low beam of headlamp.
• When the headlamp high relay is turned ON, magnetic force is
applied to the high beam solenoid (1) by a current. The mobile
valve shade (3) is switched to the high beam position through the
actuator rod (2).
• When the headlamp high relay is turned OFF, the current stops.
The mobile valve shade returns to the low beam position automati-
cally.
Component Function Check
INFOID:0000000005515043
1.
CHECK HEADLAMP (HI) OPERATION
IPDM E/R AUTO ACTIVE TEST
1.
Start IPDM E/R auto active test. Refer to
PCS-10, "Diagnosis Description"
2.
Check that the headlamp switches to the high beam.
CONSULT-III ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the headlamp switches to the high beam.
NOTE:
HI/LO is repeated 1 second each.
Does the headlamp switch to the high beam?
YES
>> Headlamp (HI) circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000005515044
1.
CHECK HEADLAMP (HI) OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1.
Turn the ignition switch OFF.
2.
Disconnect the high beam solenoid connector.
3.
Turn the ignition switch ON.
4.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
5.
With operating the test items, check the voltage between the IPDM E/R harness connector and the
ground.
JPLIA0802ZZ
Hi
: Headlamp switches to the high beam.
Off
: Headlamp OFF
HEADLAMP (HI) CIRCUIT
EXL-37
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Is the measurement value normal?
YES
>> GO TO 2.
NO
>> GO TO 3.
2.
CHECK HEADLAMP (HI) OPEN CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between the IPDM E/R harness connector and the high beam solenoid harness connec-
tor.
Does continuity exist?
YES
>> GO TO 5.
NO
>> Repair the harnesses or connectors.
3.
CHECK HEADLAMP (HI) FUSE
1.
Turn the ignition switch OFF.
2.
Check that the following fuses are not fusing.
Is the fuse fusing?
YES
>> GO TO 4.
NO
>> Replace IPDM E/R.
4.
CHECK HEADLAMP (HI) SHORT CIRCUIT
1.
Disconnect IPDM E/R connector.
2.
Check continuity between the IPDM E/R harness connector terminal and the ground.
Does continuity exist?
YES
>> Repair the harnesses or connectors. And then replace the fuse.
NO
>> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.)
Terminals
Test item
Voltage
(Approx.)
(+)
(
−
)
IPDM E/R
Ground
EXTERNAL
LAMPS
Connector
Terminal
RH
E345
89
Hi
Battery
voltage
Off
0 V
LH
90
Hi
Battery
voltage
Off
0 V
IPDM E/R
High beam solenoid
Continuity
Connector
Terminal
Connector
Terminal
RH
E345
89
E326
1
Existed
LH
90
E325
1
Unit
Location
Fuse No.
Capacity
Headlamp HI (RH) IPDM E/R
#55
10
A
Headlamp HI (LH) IPDM E/R
#54
10
A
IPDM E/R
Ground
Continuity
Connector
Terminal
RH
E345
89
Not existed
LH
90
EXL-38
< DTC/CIRCUIT DIAGNOSIS >
[XENON TYPE]
HEADLAMP (HI) CIRCUIT
5.
CHECK HEADLAMP (HI) GROUND OPEN CIRCUIT
Check continuity between the high beam solenoid harness connector and the ground.
Does continuity exist?
YES
>> Replace the front combination lamp.
NO
>> Repair the harnesses or connectors.
High beam solenoid
Ground
Continuity
Connector
Terminal
RH
E326
2
Existed
LH
E325
2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст