Nissan Murano Z51. Manual — part 1028
MIR-68
< PRECAUTION >
[WITH ADP]
PRECAUTIONS
FOR MEXICO : Precaution for Procedure without Cowl Top Cover
INFOID:0000000005716195
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc.
FOR MEXICO : Precaution Necessary for Steering Wheel Rotation after Battery Dis-
connect
INFOID:0000000005716196
NOTE:
• Before removing and installing any control units, first turn the push-button ignition switch to the LOCK posi-
tion, then disconnect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
OPERATION PROCEDURE
1.
Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2.
Turn the push-button ignition switch to ACC position.
(At this time, the steering lock will be released.)
3.
Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4.
Perform the necessary repair operation.
5.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the push-button ignition switch from ACC position to ON position, then to LOCK position. (The steering
wheel will lock when the push-button ignition switch is turned to LOCK position.)
6.
Perform self-diagnosis check of all control units using CONSULT-III.
FOR MEXICO : Precaution for Work
INFOID:0000000005716200
• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their
operation.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
PIIB3706J
PREPARATION
MIR-69
< PREPARATION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000005513425
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000005513426
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locates the noise
(J-43980)
NISSAN Squeak and Rat-
tle Kit
Repairs the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locates the noise
Remover tool
Removes the clips, pawls, and metal clips
Power tool
SIIA0995E
JMKIA3050ZZ
PIIB1407E
MIR-70
< REMOVAL AND INSTALLATION >
[WITH ADP]
INSIDE MIRROR
REMOVAL AND INSTALLATION
INSIDE MIRROR
Exploded View
INFOID:0000000005513427
Removal and Installation
INFOID:0000000005513428
CAUTION:
Never reuse the inside mirror disassembled from mirror base.
REMOVAL
1.
Remove the inside mirror cover.
2.
Remove TORX bolt.
3.
Slide the inside mirror upward to remove.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
When inserting the inside mirror into the mirror base, be sure to push the pawl until it get connected to
the mirror base.
1.
Inside mirror
2.
Inside mirror cover
3.
Mirror base
4.
TORX bolt
Refer to
for symbols in the figure.
JMLIA0136GB
OUTSIDE MIRROR
MIR-71
< REMOVAL AND INSTALLATION >
[WITH ADP]
C
D
E
F
G
H
I
J
K
M
A
B
MIR
N
O
P
OUTSIDE MIRROR
DOOR MIRROR ASSEMBLY
DOOR MIRROR ASSEMBLY : Exploded View
INFOID:0000000005513429
REMOVAL
DISASSEMBLY
1.
Door mirror assembly
2.
Front door assembly
3.
Door mirror corner cover
: Clip
JMLIA0122ZZ
JMLIA0123ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст