Nissan Murano Z51. Manual — part 637
EM-20
< PERIODIC MAINTENANCE >
SPARK PLUG
SPARK PLUG
Exploded View
INFOID:0000000005515919
Removal and Installation
INFOID:0000000005515920
REMOVAL
1.
Remove engine cover. Refer to
2.
Remove air cleaner cases (upper and lower) and air duct assembly. Refer to
.
3.
Remove electric throttle control actuator. Refer to
.
4.
Remove intake manifold collector. Refer to
5.
Remove ignition coil. Refer to
.
1.
Ignition coil
2.
Spark plug
3.
PCV hose
4.
Clamp
5.
PCV valve
6.
O-ring
7.
Rocker cover (bank 1)
8.
PCV hose
9.
Rocker cover gasket (bank 1)
10.
O-ring
11.
Camshaft position sensor (PHASE)
(bank 1)
12. Oil filler cap
13.
Rocker cover (bank 2)
14.
Rocker cover gasket (bank 2)
15.
Camshaft position sensor (PHASE)
(bank 2)
16.
PCV hose
17.
Clamp
A.
To intake manifold collector
B.
Refer to
C.
Camshaft bracket side
D.
To air duct
Refer to
for symbols in the figure.
JPBIA1637GB
SPARK PLUG
EM-21
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
6.
Remove spark plug with a spark plug wrench (commercial ser-
vice tool).
INSTALLATION
Install in the reverse order of removal.
Inspection
INFOID:0000000005515921
INSPECTION AFTER REMOVAL
Use the standard type spark plug for normal condition.
CAUTION:
• Never drop or shock spark plug.
• Never use a wire brush for cleaning.
• If plug tip is covered with carbon, spark plug cleaner may be
used.
• Spark plug gap adjustment is not required between replace-
ment intervals.
• Measure spark plug gap. When it exceeds the limit, replace
spark plug even if it is within the specified replacement mile-
age. Refer to
.
a
: 14 mm (0.55 in)
JPBIA0030ZZ
Spark plug (Standard type)
: Refer to
Cleaner air pressure:
Less than 588 kPa (6 kg/cm
2
, 85
psi)
Cleaning time:
Less than 20 seconds
SMA773C
JPBIA0031ZZ
EM-22
< PERIODIC MAINTENANCE >
CAMSHAFT VALVE CLEARANCE
CAMSHAFT VALVE CLEARANCE
Inspection and Adjustment
INFOID:0000000005515922
INSPECTION
Perform inspection as follows after removal, installation or replacement of camshaft or valve-related parts, or if
there is unusual engine conditions regarding valve clearance.
In cases of removing/installing or replacing camshaft and valve-
related parts, or of unusual engine conditions due to changes in
valve clearance (found malfunctions during stating, idling or causing
noise), perform inspection as follows:
1.
Remove rocker covers (bank 1 and bank 2). Refer to
2.
Measure the valve clearance as follows:
a.
Set No. 1 cylinder at TDC of its compression stroke.
• Rotate crankshaft pulley clockwise to align timing mark
(grooved line without color) (
) with timing indicator.
• Check that intake and exhaust cam nose on No. 1 cylinder
(engine front side of bank 1) are located as shown in the fig-
ure.
• If not, turn crankshaft one revolution (360 degrees) and align
as shown in the figure.
b.
Use a feeler gauge, measure the clearance between valve lifter
and camshaft.
: Engine front
JPBIA0164ZZ
SEM727G
: Engine front
JPBIA0044ZZ
Valve clearance
: Refer to
.
SEM139D
CAMSHAFT VALVE CLEARANCE
EM-23
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• By referring to the figure, measure the valve clearances at
locations marked “
×
” as shown in the table below (locations
indicated in the figure).
• No. 1 cylinder at compression TDC
c.
Rotate crankshaft by 240 degrees clockwise (when viewed from engine front) to align No. 3 cylinder at
TDC its compression stroke.
NOTE:
Mark a position 240 degrees (b) from a corner of the hexagonal
part of crankshaft pulley mounting bolt as shown in the figure.
Use the hexagonal part as a guide.
: Engine front
Measuring position [bank 1 (A)]
No. 1 CYL.
No. 3 CYL.
No. 5 CYL.
No. 1 cylinder at com-
pression TDC
EXH (C)
×
(B)
INT (D)
×
(E)
Measuring position [bank 2 (H)]
No. 2 CYL.
No. 4 CYL.
No. 6 CYL.
No. 1 cylinder at com-
pression TDC
INT (D)
×
(F)
EXH (C)
×
(G)
JPBIA0165ZZ
1
: Crankshaft pulley
A
: Paint mark
JPBIA0166ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст