Nissan Murano Z51. Manual — part 455
DLK-328
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR
Unit: mm (in)
1.
Remove center pillar lower garnish. Refer to
INT-20, "Removal and Installation"
.
2.
Loosen door hinge mounting nuts on door side.
3.
Adjust the surface height of rear door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts on door side.
5.
Loosen door hinge mounting nuts and bolts on body side.
6.
Raise rear door at rear end to adjust clearance of rear door according to the fitting standard dimension.
7.
After adjustment tighten bolts and nuts to the specified torque.
8.
Install center pillar lower garnish. Refer to
INT-20, "Removal and Installation"
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Exploded View
INFOID:0000000005517790
DOOR STRIKER : Removal and Installation
INFOID:0000000005517791
REMOVAL
Portion
Clearance
Surface height
Front door – Rear door
B – B
3.4 – 5.4 (0.134 – 0.213)
-1.0 – 1.0 (-0.039 – 0.039)
Rear door – Body side outer
C – C
3.4 – 5.4 (0.134 – 0.213)
-1.0 – 1.0 (-0.039 – 0.039)
Front door – Rear door
G – G
2.9 – 5.9 (0.114 – 0.237)
-1.5 – 1.5 (-0.059 – 0.059)
1.
Rear door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Seal rubber
7.
Door check link
8.
Door hinge (lower)
9.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA3686ZZ
REAR DOOR
DLK-329
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Remove TORX bolts, and then remove door striker.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check rear door open/close, lock/unlock operation after installation.
• After installation, be sure to perform the fitting adjustment. Refer to
DOOR HINGE
DOOR HINGE : Exploded View
INFOID:0000000005517792
DOOR HINGE : Removal and Installation
INFOID:0000000005517793
REMOVAL
1.
Remove center pillar lower garnish. Refer to
INT-20, "Removal and Installation"
.
2.
Remove rear door assembly. Refer to
DLK-326, "DOOR ASSEMBLY : Removal and Installation"
3.
Remove rear door hinge mounting bolts and nuts (body side), and then remove door hinge.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
• Check rear door open/close operation after installation.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
• When removing and installing rear door assembly, perform the fitting adjustment. Refer to
.
• After installing, apply the touch-up paint (the body color) onto the head of door hinge mounting nuts.
1.
Rear door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Seal rubber
7.
Door check link
8.
Door hinge (lower)
9.
Door hinge (upper)
for symbols in the figure.
JMKIA3686ZZ
DLK-330
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
REAR DOOR
DOOR CHECK LINK
DOOR CHECK LINK : Exploded View
INFOID:0000000005517794
DOOR CHECK LINK : Removal and Installation
INFOID:0000000005517795
REMOVAL
1.
Remove rear door finisher. Refer to
INT-16, "REAR DOOR FINISHER : Removal and Installation"
.
2.
Fully close the rear door window.
3.
Remove rear door speaker.
4.
Remove mounting bolts of the check link on the vehicle.
5.
Remove mounting bolts of the check link on door panel.
6.
Take door check link out from the hole of door panel.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Check rear door open/close operation after installation.
1.
Rear door panel
2.
Grommet
3.
Door striker
4.
TORX bolt
5.
Bumper rubber
6.
Seal rubber
7.
Door check link
8.
Door hinge (lower)
9.
Door hinge (upper)
Refer to
for symbols in the figure.
JMKIA3686ZZ
BACK DOOR
DLK-331
< REMOVAL AND INSTALLATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR
BACK DOOR ASSEMBLY
BACK DOOR ASSEMBLY : Exploded View
INFOID:0000000005517796
BACK DOOR ASSEMBLY : Removal and Installation
INFOID:0000000005517797
CAUTION:
Perform work with 2 workers, because of its heavy weight.
NOTE:
The back door harness constitute the back door assembly.
REMOVAL
1.
Remove back door finisher inner, back door hinge cover, back door plate. Refer to
.
1.
Back door stay
2.
Back door hinge
3.
Back door striker
4.
Bumper rubber
5.
Back door weather-strip
6.
Back door assembly
7.
Stud ball
A
: Center mark
B
: Front mark
: Vehicle front
Refer to
for symbols in the figure.
JMKIA3496ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст