Nissan Murano Z51. Manual — part 1395
ST-18
< REMOVAL AND INSTALLATION >
STEERING COLUMN
STEERING COLUMN
WITHOUT ELECTRIC MOTOR
WITHOUT ELECTRIC MOTOR : Exploded View
INFOID:0000000005514474
WITHOUT ELECTRIC MOTOR : Removal and Installation
INFOID:0000000005514475
REMOVAL
1.
Set the vehicle to the straight-ahead position.
2.
Place the tilt to the highest level. Place the telescopic to the longest level.
3.
Remove driver air bag module. Refer to
.
4.
Remove steering wheel. Refer to
.
5.
Remove instrument driver lower panel. Refer to
.
6.
Remove steering column cover. Refer to
.
7.
Remove spiral cable. Refer to
8.
Remove cluster lid A. Refer to
1.
Steering column assembly
2.
Bracket
3.
Bracket
4.
Slide plate
5.
Slide bracket
6.
Lower mount bracket
7.
Bracket
8.
Upper joint
9.
Spring
10. Tilt lever
11.
Clip
Refer to
for symbols in the figure.
JSGIA0610GB
STEERING COLUMN
ST-19
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
9.
Remove knee protector (1).
10. Disconnect each switch harness connectors installed to steering
column assembly.
11. Remove the joint mounting bolt and nut (lower shaft side), and
separate the joint from lower shaft.
12. Remove steering column assembly.
CAUTION:
• Never give axial impact to steering column assembly dur-
ing removal.
• Never move steering gear assembly when removing steering column assembly.
INSTALLATION
Note the following, and install in the reverse order of removal.
• Install the slide plate (1) and steering column housing (2) so that
the mounting dimensions (L) is within the specified range as
described below.
• Tighten the mounting bolts in the order shown in the figure when
installing the steering column assembly.
• Be careful of the following points when installing the steering col-
umn assembly.
CAUTION:
• Never give axial impact to steering column assembly during
installation.
• Never move steering gear assembly.
• Never reuse the joint mounting nut (lower shaft side).
• Adjust neutral position of steering angle sensor. Refer to
"ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL
POSITION : Special Repair Requirement"
WITHOUT ELECTRIC MOTOR : Inspection
INFOID:0000000005514476
INSPECTION AFTER REMOVAL
• Check each part of steering column assembly for damage or other malfunctions. Replace if necessary.
• Measure steering column assembly rotating torque using a preload gauge [SST: ST3127S000 (J-25765-A)].
Replace steering column assembly if outside the standard.
: Bolt
JSGIA0306ZZ
Standard
L
: 2.0 mm (0.079 in) or less
JSGIA0315ZZ
JSGIA0310ZZ
Standard
Rotating torque
: Refer to
ST-20
< REMOVAL AND INSTALLATION >
STEERING COLUMN
• Measure the length (L) as shown, if vehicle has been involved in a
minor collision. Replace steering column assembly if out side the
standard.
• Install the bracket (1) and steering column housing (2) so that the
clearance (A) is within the specified range as described below.
Replace steering column assembly if out side the standard.
INSPECTION AFTER INSTALLATION
• Check each part of steering column assembly for damage or other malfunctions. Replace if necessary.
• Check the steering wheel play, neutral position steering wheel, steering wheel turning force, and front wheel
turning angle. Refer to
.
• Check tilt and telescopic mechanism operating range tilt operating
range (L), telescopic operating range (T) as shown in the figure.
WITH ELECTRIC MOTOR
Standard
L
: Refer to
.
JSGIA0562ZZ
Standard
A
: Refer to
JSGIA0389ZZ
Standard
T
: Refer to
L
: Refer to
JSGIA0307ZZ
STEERING COLUMN
ST-21
< REMOVAL AND INSTALLATION >
C
D
E
F
H
I
J
K
L
M
A
B
ST
N
O
P
WITH ELECTRIC MOTOR : Exploded View
INFOID:0000000005514477
WITH ELECTRIC MOTOR : Removal and Installation
INFOID:0000000005514478
REMOVAL
1.
Set the vehicle to the straight-ahead position.
2.
Place the tilt to the highest level. Place the telescopic to the longest level.
3.
Remove driver air bag module. Refer to
4.
Remove steering wheel. Refer to
.
5.
Remove instrument driver lower panel. Refer to
6.
Remove steering column cover. Refer to
.
7.
Remove spiral cable. Refer to
.
8.
Remove cluster lid A. Refer to
1.
Bracket
2.
Steering column assembly
3.
Bracket
4.
Clip
5.
Tilt motor
6.
Bracket
7.
Bracket
8.
Bracket
9.
Slide bracket
10. Lower mount bracket
11.
Upper joint
12. Bracket
13. Telescopic motor
14. Bracket
15. Bracket
Refer to
JSGIA0529GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст