Nissan Murano Z51. Manual — part 1266

B210F PNP/CLUTCH INTERLOCK SWITCH

SEC-111

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

4.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to

PCS-35, "Removal and Installation"

.

NO

>> Repair or replace harness or connector.

IPDM E/R

TCM

Continuity

Connector

Terminal

Connector

Terminal

E10

72

F23

20

Existed

IPDM E/R

Ground

Continuity

Connector

Terminal

E10

72

Not existed

SEC-112

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

B2110 PNP/CLUTCH INTERLOCK SWITCH

B2110 PNP/CLUTCH INTERLOCK SWITCH

Description

INFOID:0000000005515615

IPDM E/R confirms the shift position with the following signals.
• Transmission range switch
• Shift position signal from BCM (CAN)

DTC Logic

INFOID:0000000005515616

DTC DETECTION LOGIC

NOTE:
If DTC B2110 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to

SEC-

32, "BCM : DTC Logic"

.

DTC CONFIRMATION PROCEDURE

1.

PERFORM DTC CONFIRMATION PROCEDURE

1.

Turn the ignition switch ON under the following conditions and wait for at least 1 second.

-

Selector lever is in the P or N position.

-

Do not depress brake pedal.

2.

Check “Self diagnostic result” with CONSULT-III.

Is DTC detected?

YES

>> Go to

SEC-112, "Diagnosis Procedure"

.

NO

>> INSPECTION END

Diagnosis Procedure

INFOID:0000000005515617

1.

CHECK DTC WITH TCM

Check “Self diagnostic result” with CONSULT-III. Refer to

TM-122, "DTC Index"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK TRANSMISSION RANGE SWITCH INPUT SIGNAL

1.

Turn ignition switch ON.

2.

Check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to

PCS-35, "Removal and Installation"

.

NO

>> GO TO 3.

3.

CHECK TRANSMISSION RANGE SWITCH CIRCUIT

DTC No.

Trouble diagnosis

name

DTC detecting condition

Possible cause

B2110

INTER LOCK/PNP
SW

IPDM E/R detects mismatch between the signals
below for 1 second or more.
• Transmission range switch input signal
• Shift position signal from BCM (CAN)

• Harness or connectors

(Transmission range switch circuit is
open or shorted)

• Transmission range switch
• IPDM E/R
• BCM

(+)

(–)

Condition

Voltage (V)

(Approx.)

IPDM E/R

Connector

Terminal

E10

30

Ground

Selector lever

P or N

Battery voltage

Other than above

0

B2110 PNP/CLUTCH INTERLOCK SWITCH

SEC-113

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

C

D

E

F

G

H

I

J

L

M

A

B

SEC

N

O

P

1.

Turn ignition switch OFF.

2.

Disconnect TCM connector and IPDM E/R connector.

3.

Check continuity between IPDM E/R harness connector and TCM harness connector.

4.

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?

YES

>> Replace IPDM E/R. Refer to

PCS-35, "Removal and Installation"

.

NO

>> Repair or replace harness or connector.

IPDM E/R

TCM

Continuity

Connector

Terminal

Connector

Terminal

E10

72

F23

20

Existed

IPDM E/R

Ground

Continuity

Connector

Terminal

E10

72

Not existed

SEC-114

< DTC/CIRCUIT DIAGNOSIS >

[WITH INTELLIGENT KEY SYSTEM]

POWER SUPPLY AND GROUND CIRCUIT

POWER SUPPLY AND GROUND CIRCUIT

BCM

BCM : Diagnosis Procedure

INFOID:0000000005515618

1.

CHECK FUSE AND FUSIBLE LINK

Check that the following fuse and fusible link are not blown.

Is the fuse fusing?

YES

>> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is

blown.

NO

>> GO TO 2.

2.

CHECK POWER SUPPLY CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect BCM connectors.

3.

Check voltage between BCM harness connector and ground.

Is the measurement value normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness or connector.

3.

CHECK GROUND CIRCUIT

Check continuity between BCM harness connector and ground.

Does continuity exist?

YES

>> INSPECTION END

NO

>> Repair or replace harness or connector.

IPDM E/R

IPDM E/R : Diagnosis Procedure

INFOID:0000000005515619

Refer to

PCS-18, "Diagnosis Procedure"

.

Signal name

Fuse and fusible link No.

Battery power supply

L

10

(+)

(

−

)

Voltage (V)

(Approx.)

BCM

Connector

Terminal

M118

1

Ground

Battery voltage

M119

11

BCM

Ground

Continuity

Connector

Terminal

M119

13

Existed