Nissan Murano Z51. Manual — part 1466
INTAKE DOOR MOTOR
VTL-35
< REMOVAL AND INSTALLATION >
[WITHOUT 7 INCH DISPLAY]
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
3.
Remove the mounting screws (A), and then remove the intake
door motor (1).
4.
Disconnect the intake door motor connector.
INSTALLATION
Install in the reverse order of removal.
JPIIA0570ZZ
VTL-36
< REMOVAL AND INSTALLATION >
[WITHOUT 7 INCH DISPLAY]
HEATER & COOLING UNIT ASSEMBLY
HEATER & COOLING UNIT ASSEMBLY
Exploded View
INFOID:0000000005517127
REMOVAL
DISASSEMBLY
1.
Blower unit assembly
2.
Heater & cooling unit assembly
3.
Steering member
4.
Instrument stay
5.
Instrument panel assembly
for symbols in the figure.
JPIIA1224GB
HEATER & COOLING UNIT ASSEMBLY
VTL-37
< REMOVAL AND INSTALLATION >
[WITHOUT 7 INCH DISPLAY]
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
1.
Ventilator seal
2.
Upper ventilator seal
3.
Defroster seal
4.
Adapter case
5.
Center case
6.
Intake sensor bracket
7.
Intake sensor
8.
Upper ventilator door motor
9.
Upper ventilator door rod
10.
Upper ventilator door lever
11.
Filter cover
12. In-cabin microfilter/Air conditioner fil-
ter*
13.
Foot duct 1 (right)
14.
Foot duct 2 (right)
15. Air mix door motor (passenger side)
16.
Heater & cooling unit case cover
17.
Evaporator pipe assembly
18. O-ring
19.
Evaporator
20.
Expansion valve
21. Case packing
22.
Grommet
23.
Cooler pipe grommet
24. Drain hose
25.
Heater & cooling unit case (right)
26.
Air mix door (Slide door)
27. Heater pipe support
28.
Heater pipe grommet
29.
Heater & cooling unit case (left)
30. Heater core
31.
Heater pipe cover
32.
Foot duct 2 (left)
33. Foot duct 1 (left)
34.
Heater duct
35.
Aspirator
36. Aspirator hose
37.
Mode door motor
38.
Main link
39. Rod link
40.
Max. cool door link
41.
Ventilator door link
42. Foot door link
43.
Mode door lever
44.
Defroster door link
45. Ventilator door lever
46.
Foot door lever
47.
Defroster door lever
48. Max. cool door lever
49.
Air mix door motor (driver side)
50.
Distributor upper case
51. Distributor lower case
52.
Ventilator door
53.
Foot door
54. Max. cool door
55.
Defroster door
56.
Upper ventilator door
JPIIA0454GB
VTL-38
< REMOVAL AND INSTALLATION >
[WITHOUT 7 INCH DISPLAY]
HEATER & COOLING UNIT ASSEMBLY
Removal and Installation
INFOID:0000000005517128
REMOVAL
1.
Collect the refrigerant with refrigerant collecting equipment (for HFC134a).
2.
Drain engine coolant. Refer to
.
3.
Remove the mounting bolt (A), and then disconnect the low-
pressure pipe (1) and high-pressure pipe (2) from the expansion
valve.
CAUTION:
Cap or wrap the joint of the A/C piping and expansion valve-
with suitable material such as vinyl tape to avoid the entry
of air.
4.
Remove the clamps (A), and then disconnect the heater hoses
(1).
CAUTION:
• Some coolant may spill when heater hoses are discon-
nected. Wipe them off with wastes.
• Close the coolant inlet/outlet on the heater core and
heater hoses with wastes.
5.
Remove the instrument panel assembly. Refer to
.
6.
Remove the mounting nuts (A), and then remove the instrument
stay (1).
*
: Models for Mexico.
for symbols in the figure.
JPIIA0561ZZ
JPIIA0571ZZ
JPIIA0565ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст