Nissan Murano Z51. Manual — part 659
EM-108
< UNIT DISASSEMBLY AND ASSEMBLY >
OIL SEAL
1.
Remove the following parts:
• Road wheel and tire (RH)
• Splash guard (RH): Refer to
EXT-24, "FENDER PROTECTOR : Exploded View"
.
• Drive belt: Refer to
EM-17, "Removal and Installation"
• Crankshaft pulley: Refer to
.
2.
Remove front oil seal using a suitable tool.
CAUTION:
Be careful not to damage front timing chain case and crank-
shaft.
INSTALLATION
1.
Apply new engine oil to both oil seal lip and dust seal lip of new front oil seal.
2.
Install front oil seal.
• Install front oil seal so that each seal lip is oriented as shown in
the figure.
• Using a suitable drift, press-fit until the height of front oil seal is
level with the mounting surface.
- Suitable drift: outer diameter 60 mm (2.36 in), inner diameter
50 mm (1.97 in).
• Check the garter spring is in position and seal lips not inverted.
CAUTION:
• Be careful not to damage front timing chain case and
crankshaft.
• Press-fit straight and avoid causing burrs or tilting oil
seal.
3.
Install in the reverse order of removal after this step.
REAR OIL SEAL
REAR OIL SEAL : Removal and Installation
INFOID:0000000005515966
REMOVAL
1.
Remove transaxle assembly. Refer to
2.
Remove drive plate. Refer to
3.
Remove oil pan (upper). Refer to
.
SEM829E
A
: Oil seal lip
B
: Dust seal lip
: Engine inside
: Engine outside
JPBIA0054ZZ
SEM829E
OIL SEAL
EM-109
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
4.
Use a seal cutter (SST) to cut away liquid gasket and remove
rear oil seal retainer.
CAUTION:
Be careful not to damage mating surfaces.
NOTE:
Regard both rear oil seal and retainer an assembly.
INSTALLATION
1.
Remove old liquid gasket on mating surfaces of cylinder block and oil pan (upper) using scraper.
2.
Apply new engine oil to both oil seal lip and dust seal lip of new oil seal retainer.
3.
Apply a continuous bead of liquid gasket with the tube presser
(commercial service tool) to rear oil seal retainer as shown in the
figure.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-18, "Recommended Chemical Products and Sealants"
.
CAUTION:
Attaching should be done within 5 minutes after coating.
4.
Install rear oil seal retainer to cylinder block. Refer to
• Check the garter spring is in position and seal lips not inverted.
5.
Install in the reverse order of removal after this step.
SEM830E
a
:
φ
2.0 - 3.0 mm (0.08 - 0.12 in)
JPBIA0542ZZ
EM-110
< UNIT DISASSEMBLY AND ASSEMBLY >
CYLINDER HEAD
CYLINDER HEAD
Exploded View
INFOID:0000000005515967
REMOVAL
DISASSEMBLY
1.
Oil level gauge
2.
Cylinder head (bank 2)
3.
Cylinder head bolt
4.
Cylinder head (bank 1)
5.
Cylinder head gasket (bank 1)
6.
Cylinder head gasket (bank 2)
A.
Refer to
Refer to
for symbols in the figure.
JPBIA1748ZZ
CYLINDER HEAD
EM-111
< UNIT DISASSEMBLY AND ASSEMBLY >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
Removal and Installation
INFOID:0000000005515968
REMOVAL
1.
Remove the following parts:
• Oil level gauge
• Intake manifold collector: Refer to
.
• Rocker cover: Refer to
• Fuel tube and fuel injector assembly: Refer to
• Intake manifold: Refer to
• Exhaust manifold: Refer to
• Water inlet and thermostat assembly: Refer to
.
• Water outlet, water connector, water bypass pipe, and heater pipe: Refer to
• Timing chain and rear timing chain case: Refer to
and
.
• Camshaft: Refer to
.
1.
Valve lifter
2.
Valve collet
3.
Valve spring retainer
4.
Valve spring
5.
Valve oil seal
6.
Valve spring seat
7.
Valve guide (EXH)
8.
Spark plug
9.
Spark plug tube
10. Cylinder head (bank 1)
11.
Valve seat (EXH)
12. Valve (EXH)
13. Valve (INT)
14. Valve seat (INT)
15. Valve guide (INT)
16. Cylinder head (bank 2)
: Apply genuine high strength thread locking sealant or equivalent.
Refer to
for symbols not described on the above.
JPBIA1728GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст