Nissan Murano Z50 (2003 year). Manual — part 280
WT-6
ROAD WHEEL TIRE ASSEMBLY
Revision; 2004 April
2003 Murano
ROAD WHEEL TIRE ASSEMBLY
PFP:40300
Balancing Wheels (Bonding Weight Type)
AES000HD
REMOVAL
1.
Remove inner and outer balance weights from the road wheel.
CAUTION:
Be careful not to scratch the road wheel during removal.
2.
Using releasing agent, remove double-faced adhesive tape from the road wheel.
CAUTION:
●
Be careful not to scratch the road wheel during removal.
●
After removing double-faced adhesive tape, wipe clean traces of releasing agent from the road
wheel.
WHEEL BALANCE ADJUSTMENT
●
If a tire balance machine has adhesion balance weight mode settings and drive-in weight mode setting,
select and adjust a drive-in weight mode suitable for road wheels.
1.
Set road wheel on wheel balancer using the center hole as a guide. Start the tire balance machine.
2.
When inner and outer unbalance values are shown on the wheel balancer indicator, multiply outer unbal-
ance value by 5/3 to determine balance weight that should be used. Select the outer balance weight with
a value closest to the calculated value above and install it to the designated outer position of, or at the
designated angle in relation to the road wheel.
CAUTION:
●
Do not install the inner balance weight before installing the outer balance weight.
●
Before installing the balance weight, be sure to clean the
mating surface of the road wheel.
Indicated unbalance value
×
5/3 = balance weight to be installed
Calculation example:
23 g (0.81 oz)
×
5/3 = 38.33 g (1.35 oz) = 40 g (1.41 oz) balance
weight (closer to calculated balance weight value)
Note that balance weight value must be closer to the calculated
balance weight value.
Example:
37.4 = 35 g (1.23 oz)
37.5 = 40 g (1.41 oz)
a.
Install balance weight in the position shown in the figure.
b.
When installing balance weight to road wheels, set it into the
grooved area on the inner wall of the road wheel as shown in the
figure so that the balance weight center is aligned with the wheel
balancer indication position (angle).
CAUTION:
●
Always use genuine Nissan adhesion balance weights.
●
Balance weights are unreusable; always replace with new
ones.
●
Do not install more than three pieces of balance weight.
SMA054D
SMA055D
ROAD WHEEL TIRE ASSEMBLY
WT-7
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision; 2004 April
2003 Murano
c.
If calculated balance weight value exceeds 50 g (1.76 oz), install
two balance weight pieces in line with each other (as shown in
the figure).
CAUTION:
Do not install one balance weight piece on top of another.
3.
Start wheel balancer again.
4.
Install drive-in balance weight on inner side of road wheel in the
wheel balancer indication position (angle).
CAUTION:
Do not install more than two balance weights.
5.
Start wheel balancer. Make sure that inner and outer residual
unbalance values are 10 g (0.35 oz) each or below.
●
If either residual unbalance value exceeds 10 g (0.35 oz), repeat installation procedures.
Wheel balance (Maximum allowable unbalance):
Rotation
AES000MY
●
After rotating the tires, adjust the tire pressure.
●
Retighten the wheel nuts when the vehicle has been driven for
1,000 km (600 miles) (also in cases of a flat tire, etc.).
CAUTION:
When installing wheels, tighten them diagonally by dividing
the work two to three times in order to prevent the wheels
from developing any distortion.
Maximum allowable
unbalance
Dynamic (At rim flange)
10 g (0.35 oz) (one side)
Static (At rim flange)
20 g (0.71 oz)
SMA056D
Tightening torque of wheel nut:
98.1 - 127 N·m (10 - 12 kg-m, 73 - 93 ft-lb)
SMA829C
WT-8
LOW TIRE PRESSURE WARNING SYSTEM
Revision; 2004 April
2003 Murano
LOW TIRE PRESSURE WARNING SYSTEM
PFP:40300
System Components
AES000HG
System Description
AES000HH
TRANSMITTER
A sensor-transmitter integrated with a valve is installed on a wheel,
and transmits a detected air pressure signal in the form of a radio
wave.
SEIA0309E
SEIA0203E
LOW TIRE PRESSURE WARNING SYSTEM
WT-9
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision; 2004 April
2003 Murano
ANTENNA
Receives the radio wave signal transmitted by the transmitter.
LOW TIRE PRESSURE WARNING CONTROL UNIT
Reads the radio wave signal received by the antenna, and controls
the warning lamp and the buzzer operations as shown below. It also
has a judgement function to detect a system malfunction.
DISPLAY UNIT
Displays the air pressure of each tire.
●
After the ignition switch is turned ON, the pressure values are
not be displayed until the data of each wheel stabilizes.
SEIA0346E
SEIA0306E
Condition
Warning lamp
Buzzer
Less than 190 kPa (1.9 kg/cm
2
, 27 psi)
[Flat tire]
ON
Sounds for
10 sec.
System malfunction
ON
OFF
SEIA0307E
SEIA0310E
WT-10
CAN COMMUNICATION
Revision; 2004 April
2003 Murano
CAN COMMUNICATION
PFP:23710
System Description
AES000OJ
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication Unit For 2WD Models
AES000Y0
Go to CAN system, when selecting your CAN system type from the following table.
×
: Applicable
TYPE 1/TYPE 2/TYPE 3/TYPE 4/TYPE 5/TYPE 6/TYPE 7/TYPE 8
System Diagram
●
Type1
Body type
Wagon
Axle
2WD
Engine
VQ35DE
Transmission
CVT
Brake control
ABS
VDC
Low tire pressure warning
system
×
×
×
×
×
×
×
×
Navigation system
×
×
×
×
×
×
×
×
Automatic drive positioner
×
×
×
×
×
×
×
×
CAN communication type
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
SKIA4902E
CAN COMMUNICATION
WT-11
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision; 2004 April
2003 Murano
●
Type2
●
Type3
●
Type4
SKIA4903E
SKIA4904E
SKIA4905E
WT-12
CAN COMMUNICATION
Revision; 2004 April
2003 Murano
●
Type5
●
Type6
●
Type7
SKIA4906E
SKIA4907E
SKIA4908E
CAN COMMUNICATION
WT-13
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision; 2004 April
2003 Murano
●
Type8
SKIA4909E
WT-14
CAN COMMUNICATION
Revision; 2004 April
2003 Murano
Input/output Signal Chart
T: Transmit R: Receive
Signals
ECM
TCM
Low
tire
pres-
sure
warn-
ing
control
unit
Dis-
play
unit
Dis-
play
control
unit
BCM
Uni-
fied
meter
and
A/C
amp.
Driver
seat
control
unit
ABS
actua-
tor and
elec-
tric unit
(con-
trol
unit)
IPDM
E/R
Engine speed signal
T
R
R
R
R
Engine status signal
T
R
Engine coolant temperature signal
T
R
CVT position indicator signal
T
R
Second position signal
R
T
Second position indicator signal
T
R
Engine and CVT integrated control
signal
T
R
R
T
Accelerator pedal position signal
T
R
Closed throttle position signal
T
R
Wide open throttle position signal
T
R
Key switch signal
T
R
Ignition switch signal
T
R
R
P range signal
T
R
Stop lamp switch signal
R
T
Fuel consumption monitor signal
T
R
CVT self-diagnosis signal
R
T
ABS operation signal
R
T
Air conditioner switch signal
R
T
A/C compressor request signal
T
R
A/C compressor feedback signal
T
R
Blower fan motor switch signal
R
T
A/C control signal
T
T
R
R
R
T
Cooling fan speed request signal
T
R
Position lights request signal
T
R
R
Low beam request signal
T
R
Low beam status signal
R
T
High beam request signal
T
R
R
High beam status signal
R
T
Front fog lights request signal
T
R
Vehicle speed signal
R
R
T
R
R
R
R
T
R
Sleep request 1 signal
T
R
Sleep request 2 signal
T
R
Door switch signal
R
T
R
R
T
R
R
R
Turn indicator signal
T
R
CAN COMMUNICATION
WT-15
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision; 2004 April
2003 Murano
Key fob ID signal
T
R
Key fob door unlock signal
T
R
Seat belt buckle switch signal
R
T
Oil pressure switch signal
R
T
T
R
Buzzer output signal
T
R
Fuel level sensor signal
R
T
Fuel level low warning signal
R
R
T
Malfunction indicator lamp signal
T
R
ASCD SET lamp signal
T
R
ASCD CRUISE lamp signal
T
R
Input shaft revolution signal
R
T
Output shaft revolution signal
R
T
Front wiper request signal
T
R
Front wiper stop position signal
R
T
Rear window defogger switch signal
T
R
Rear window defogger control signal
R
R
R
T
Hood switch signal
R
T
Theft warning horn request signal
T
R
Horn chirp signal
T
R
Tire pressure signal
T
R
Tire pressure data signal
T
R
R
ABS warning lamp signal
R
T
Brake warning lamp signal
R
T
System setting signal
T
T
R
Parking brake switch signal
R
T
Signals
ECM
TCM
Low
tire
pres-
sure
warn-
ing
control
unit
Dis-
play
unit
Dis-
play
control
unit
BCM
Uni-
fied
meter
and
A/C
amp.
Driver
seat
control
unit
ABS
actua-
tor and
elec-
tric unit
(con-
trol
unit)
IPDM
E/R
WT-16
CAN COMMUNICATION
Revision; 2004 April
2003 Murano
TYPE 9/TYPE10/TYPE 11/TYPE 12/TYPE 13/TYPE 14/TYPE 15/TYPE 16
System Diagram
●
Type9
●
Type10
●
Type11
SKIA4910E
SKIA4911E
SKIA4912E
CAN COMMUNICATION
WT-17
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision; 2004 April
2003 Murano
●
Type12
●
Type13
●
Type14
SKIA4913E
SKIA4914E
SKIA4915E
WT-18
CAN COMMUNICATION
Revision; 2004 April
2003 Murano
●
Type15
●
Type16
SKIA4916E
SKIA4917E
CAN COMMUNICATION
WT-19
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision; 2004 April
2003 Murano
Input/Output Signal Chart
T: Transmit R: Receive
Signals
ECM
TCM
Low
tire
pres-
sure
warn-
ing
con-
trol
unit
Dis-
play
unit
Dis-
play
con-
trol
unit
BCM
Uni-
fied
meter
and
A/C
amp.
Steer-
ing
angle
sen-
sor
Driver
seat
con-
trol
unit
ABS
actua-
tor
and
elec-
tric
unit
(con-
trol
unit)
IPDM
E/R
Engine speed signal
T
R
R
R
R
R
Engine status signal
T
R
Engine coolant temperature signal
T
R
Engine and CVT integrated control
signal
T
R
R
T
Accelerator pedal position signal
T
R
R
Closed throttle position signal
T
R
Wide open throttle position signal
T
R
Key switch signal
T
R
Ignition switch signal
T
R
R
P range signal
T
R
R
Stop lamp switch signal
R
T
VDC operation signal
R
T
Second position indicator signal
T
R
R
Second position signal
R
T
Fuel consumption monitor signal
T
R
CVT self-diagnosis signal
R
T
Input shaft revolution signal
R
T
R
Output shaft revolution signal
R
T
R
Air conditioner switch signal
R
T
A/C compressor request signal
T
R
A/C compressor feedback signal
T
R
Blower fan motor switch signal
R
T
A/C control signal
T
T
R
R
R
T
Cooling fan speed request signal
T
R
Position lights request signal
T
R
R
Low beam request signal
T
R
Low beam status signal
R
T
High beam request signal
T
R
R
High beam status signal
R
T
Front fog lights request signal
T
R
Vehicle speed signal
R
R
T
R
R
R
R
T
R
Sleep request 1 signal
T
R
Sleep request 2 signal
T
R
WT-20
CAN COMMUNICATION
Revision; 2004 April
2003 Murano
Door switch signal
R
T
R
R
T
R
R
R
Turn indicator signal
T
R
Key fob ID signal
T
R
Key fob door unlock signal
T
R
Seat belt buckle switch signal
R
T
Oil pressure switch signal
R
T
T
R
Buzzer output signal
T
R
Fuel level sensor signal
R
T
Fuel level low warning signal
R
R
T
Malfunction indicator signal
T
R
ASCD SET lamp signal
T
R
ASCD CRUISE lamp signal
T
R
Front wiper request signal
T
R
Front wiper stop position signal
R
T
Rear window defogger switch signal
T
R
Rear window defogger control signal
R
R
R
T
Hood switch signal
R
T
Theft warning horn request signal
T
R
Horn chirp signal
T
R
Steering angle sensor signal
T
R
Tire pressure signal
T
R
Tire pressure data signal
T
R
R
CVT position indicator signal
T
R
R
ABS warning lamp signal
R
T
VDC OFF indicator lamp signal
R
T
SLIP indicator lamp signal
R
T
Brake warning lamp signal
R
T
System setting signal
T
T
R
Parking brake switch signal
R
T
Signals
ECM
TCM
Low
tire
pres-
sure
warn-
ing
con-
trol
unit
Dis-
play
unit
Dis-
play
con-
trol
unit
BCM
Uni-
fied
meter
and
A/C
amp.
Steer-
ing
angle
sen-
sor
Driver
seat
con-
trol
unit
ABS
actua-
tor
and
elec-
tric
unit
(con-
trol
unit)
IPDM
E/R
CAN COMMUNICATION
WT-21
C
D
F
G
H
I
J
K
L
M
A
B
WT
Revision; 2004 April
2003 Murano
CAN Communication Unit For AWD Models
AES000Y1
Go to CAN system, when selecting your CAN system type from the following table.
×
: Applicable
TYPE 17/TYPE 18/TYPE 19/TYPE 20/TYPE 21/TYPE 22/TYPE 23/TYPE 24
System Diagram
●
Type17
●
Type18
Body type
Wagon
Axle
AWD
Engine
VQ35DE
Transmission
CVT
Brake control
ABS
VDC
Low tire pressure warning
system
×
×
×
×
×
×
×
×
Navigation system
×
×
×
×
×
×
×
×
Automatic drive positioner
×
×
×
×
×
×
×
×
CAN system type
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
SKIA4918E
SKIA4919E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст