Nissan Murano Z50 (2003 year). Manual — part 270
SE-112
POWER SEAT
Revision; 2004 April
2003 Murano
POWER SEAT
PFP:87016
Automatic Drive Positioner Interlocking Power Seat
AIS003HO
Automatic drive positioner interlocking power seat. Refer to
SE-12, "AUTOMATIC DRIVE POSITIONER"
.
POWER SEAT
SE-113
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision; 2004 April
2003 Murano
Power Seat (Only Manual Operation Model)
AIS003HN
SCHEMATIC
TIWA0315E
SE-114
POWER SEAT
Revision; 2004 April
2003 Murano
WIRING DIAGRAM–SEAT– FOR DRIVER SEAT
TIWA0316E
POWER SEAT
SE-115
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision; 2004 April
2003 Murano
TIWA0317E
SE-116
POWER SEAT
Revision; 2004 April
2003 Murano
WIRING DIAGRAM–SEAT– FOR PASSENGER SEAT
TIWA0318E
HEATED SEAT
SE-117
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision; 2004 April
2003 Murano
HEATED SEAT
PFP:87335
Description
AIS001TK
●
When handling seat, be extremely careful not to scratch heating unit.
●
To replace heating unit, seat trim and pad should be separated.
●
Do not use any organic solvent, such as thinner, benzene, alcohol, etc. to clean trims.
SBT314
SE-118
HEATED SEAT
Revision; 2004 April
2003 Murano
Schematic
AIS001TL
TIWA0319E
HEATED SEAT
SE-119
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision; 2004 April
2003 Murano
Wiring Diagram – HSEAT –
AIS001TM
TIWA0320E
SE-120
HEATED SEAT
Revision; 2004 April
2003 Murano
TIWA0321E
HEATED SEAT
SE-121
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision; 2004 April
2003 Murano
TIWA0322E
SE-122
FRONT SEAT
Revision; 2004 April
2003 Murano
FRONT SEAT
PFP:87000
Removal and Installation
AIS005VU
DRIVER SIDE POWER SEAT
PIIA4301E
FRONT SEAT
SE-123
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision; 2004 April
2003 Murano
1.
Seatback board
2.
Headrest
3.
Headrest holder (locked)
4.
Headrest holder (free)
5.
Lumbar support lever knob
6.
Seatback trim
7.
Seatback pad
8.
Seatback frame
9.
Inner stay
10. Side air bag module
11.
Seat cushion trim
12. Seat cushion pad
13. Seat cushion frame
14. Power seat harness
15. Seat cushion inner finisher
16. Reclining inner device
17. Reclining device rod
18. Reclining outer device
19. Seat belt buckle
20. Seat lifter link slide assembly
21. Power seat switch
22. Pedal adjusting switch
23. Seat cushion outer finisher
24. Slide & lifter switch knob
25. Reclining switch knob
26. Seat cushion under cover
27. Seat cushion front finisher
28. Seat control unit
29. Seat cushion outer cover
SE-124
FRONT SEAT
Revision; 2004 April
2003 Murano
PASSENGER SIDE MANUAL SEAT
PIIA4302E
FRONT SEAT
SE-125
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision; 2004 April
2003 Murano
REMOVAL
When removing or installing the seat trim, carefully handle it to keep dirt out and avoid damage.
CAUTION:
●
Before removing the front seat, turn ignition switch OFF, disconnect both battery cables and wait
least 3 minutes.
●
When checking the power seat circuit for continuity using a circuit tester, do not confuse its con-
nector with the side air bag module connector. Such an error may cause the air bag to deploy.
●
Do not drop, tilt, or bump the side air bag module installing in the seat. Always handle it with care.
1.
Remove the front leg cover and rear leg cover (LH/RH).
NOTE:
●
Slide the seat backward, and disconnect the front tabs on the
front leg cover. Then move the cover toward the rear of the
vehicle, and pull up to remove.
●
Slide the seat forward, then disengage the tabs on the front
LH/RH of the rear leg cover and tabs engaged into the rail.
Then pull the cover toward the rear of the vehicle.
2.
Slide the seat until the body mounting bolts are visible and a tool can be inserted.
NOTE:
●
When disassembling the driver seat after removal, set the front/rear cushion lifter to the top position.
3.
Remove the body mounting bolts.
4.
Disconnect both battery cables.
5.
Remove the harness connector for the side air bag module.
6.
Remove the power seat harness connector and vehicle harness fixing clip out of the vehicle.
NOTE:
When removing and installing, using shop clothes, protect the parts from damage where it may interfere
with others.
INSTALLATION
Install in the reverse order of removal.
NOTE:
Be sure to insert the rear end tab of the rear leg cover under the rail.
1.
Seatback board
2.
Headrest
3.
Headrest holder (free)
4.
Headrest holder (locked)
5.
Seatback trim
6.
Seatback pad
7.
Seatback frame
8.
Inner stay
9.
Side air bag module
10. Seat cushion trim
11.
Seat cushion pad
12. Seat cushion frame
13. Seat cushion inner cover
14. Seat cushion outer cover
15. Seat harness
16. Seat cushion inner finisher
17. Seat belt buckle
18. Seat slide assembly
19. Seat cushion outer finisher
20. Reclining lever knob
PIIA4303E
SE-126
FRONT SEAT
Revision; 2004 April
2003 Murano
SEATBACK TRIM AND PAD
NOTE:
Be sure to set the front/rear cushion lifter to the top position.
Removal
1.
Remove the seatback board from the back of the seatback.
2.
Remove the retainer.
3.
Pull snap ring upward, and remove lumber support lever knob
front seatback frame.
4.
Squeeze and pull up headrest holder tabs to remove front seat-
back frame.
NOTE:
Before installing the headrest holder, check its orientation (front/
rear and left/right).
PIIA4304E
PIIA4305E
PIIA1156E
PIIA1158E
FRONT SEAT
SE-127
C
D
E
F
G
H
J
K
L
M
A
B
SE
Revision; 2004 April
2003 Murano
5.
Remove the stay securing the inner cloth.
6.
Remove the seat heater harness connector. After removing the seatback trim and pad, remove the hog
ring to separate the trim, pad and seatback heater unit.
Installation
Install in the reverse order of removal.
REMOVAL OF SEATBACK ASSEMBLY
1.
After completing the steps 1 and 2 of “SEATBACK TRIM AND PAD”, remove the harness connectors for
the reclining motor and lumbar support motor (driver seat only).
2.
Pull out the harness connector for the side air bag from the seat cushion.
3.
Remove the reclining device mounting bolts on the seatback frame, and remove the seatback assembly.
NOTE:
When assembling the seatback frame, make sure that the reclining device are locked on both sides, and
be sure to temporarily tighten the bolts, then tighten them finally.
INSTALLATION OF SEATBACK ASSEMBLY
Install in the reverse order of removal.
SEAT CUSHION TRIM AND PAD (POWER SEAT)
Removal
1.
Remove the seat cushion front finisher.
2.
Remove the power seat switch knob.
3.
Remove the seat cushion outer finisher.
4.
Remove the power seat switch assembly.
5.
Partially pull off the trim at the rear of the seat cushion forward,
and remove the hog rings on the seat cushion pad.
6.
Remove the retainer on the seat cushion frame, then remove the harness connector for the seat heater.
7.
After removing the seat cushion trim and pad, remove the hog rings to separate the trim and pad.
PIIA6082E
PIIA4306E
SIIA0503E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст