Nissan Murano Z50 (2003 year). Manual — part 225
LT-88
HEADLAMP -CONVENTIONAL TYPE-
Revision; 2004 April
2003 Murano
How to Proceed With Trouble Diagnosis
AKS007LT
1.
Confirm the symptom or customer complaint.
2.
Understand operation description and function description. Refer to
.
3.
Perform the Preliminary Check. Refer to
.
4.
Check symptom and repair or replace the cause of malfunction.
5.
Does the headlamp operate normally? If YES: GO TO 6. If NO: GO TO 4.
6.
INSPECTION END
Preliminary Check
AKS007LU
CHECK POWER SUPPLY AND GROUND CIRCUIT
1.
CHECK FUSES
●
Check for blown fuses.
Refer to
LT-83, "Wiring Diagram — H/LAMP —"
OK or NG
OK
>> GO TO 2.
NG
>> If fuse is blown, be sure to eliminate cause of malfunction before installing new fuse. Refer to
3, "POWER SUPPLY ROUTING CIRCUIT"
2.
CHECK POWER SUPPLY CIRCUIT
1.
Disconnect BCM connector.
2.
Check voltage between BCM harness connector and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Check harness for open or short between BCM and fuse.
Unit
Power source
Fuse and fusible link No.
BCM
Battery
F
Ignition switch ON or START position
1
Ignition switch ACC or ON position
6
IPDM E/R
Battery
83
84
85
86
Terminals
Ignition switch position
(+)
(-)
OFF
ACC
ON
Connector
Terminal
(Wire color)
E118
7 (W/B)
Ground
Battery
voltage
Battery
voltage
Battery
voltage
M35
35 (R)
0V
0V
Battery
voltage
M35
36 (P/B)
0V
Battery
voltage
Battery
voltage
SKIA3192E
HEADLAMP -CONVENTIONAL TYPE-
LT-89
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision; 2004 April
2003 Murano
3.
CHECK GROUND CIRCUIT
Check continuity between BCM harness connector and ground.
OK or NG
OK
>> INSPECTION END
NG
>> Check harness ground circuit.
CONSULT-II Function
AKS007LV
CONSULT-II performs the following functions communicating with BCM.
CONSULT-II BASIC OPERATION
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carry out CAN communication.
1.
With ignition switch OFF, connect CONSULT-II and CONSULT-II
CONVERTER to data link connector, then turn ignition switch
ON.
2.
Touch “START (NISSAN BASED VHCL)”.
Terminals
Continuity
Connector
Terminal (Wire color)
Ground
Yes
E118
8 (B)
SKIA3193E
BCM diagnosis
part
Check item, diagnosis mode
Description
HEAD LAMP
WORK SUPPORT
Changes the setting for each function.
DATA MONITOR
Displays BCM input data in real time.
ACTIVE TEST
Operation of electrical loads can be checked by sending drive signal to them.
BCM C/U
CAN DIAG SUPPORT MNTR
The result of transmit/receive diagnosis of CAN communication can be read.
PBIB1300E
SKIA3098E
LT-90
HEADLAMP -CONVENTIONAL TYPE-
Revision; 2004 April
2003 Murano
3.
Touch “BCM” on “SELECT SYSTEM” screen.
If “BCM” is not indicated, refer to
4.
Touch “HEAD LAMP” on “SELECT TEST ITEM” screen.
WORK SUPPORT
Operation Procedure
1.
Touch “HEAD LAMP” on “SELECT TEST ITEM” screen.
2.
Touch “WORK SUPPORT” on “SELECT DIAG MODE” screen.
3.
Touch “BATTERY SAVER SET” on “SELECT WORK ITEM” screen.
4.
Touch “START”.
5.
Touch “CHANGE SET”.
6.
The setting will be changed and “CUSTOMIZING COMPLETED” will be displayed.
7.
Touch “END”.
Display Item List
DATA MONITOR
Operation Procedure
1.
Touch “HEAD LAMP” on “SELECT TEST ITEM” screen.
2.
Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.
3.
Touch either “ALL SIGNALS” or “SELECTION FROM MENU” on “DATA MONITOR” screen.
4.
Touch “START”.
5.
When “SELECTION FROM MENU” is selected, touch individual items to be monitored. When “ALL SIG-
NALS” is selected, all the items will be monitored.
6.
Touch “RECORD” while monitoring, then the status of the monitored item can be recorded. To stop
recording, touch “STOP”.
SKIA6338E
SKIA1922E
Item
Description
CONSULT-II
Factory setting
BATTERY SAVER SET
Exterior lamp battery saver control mode can be changed
in this mode. Selects exterior lamp battery saver control
mode between two ON/OFF.
ON
×
OFF
—
All signals
Monitors all the signals.
Selection from menu
Selects and monitors individual signal.
HEADLAMP -CONVENTIONAL TYPE-
LT-91
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision; 2004 April
2003 Murano
Display Item List
NOTE:
Vehicles without auto light system display this item, but cannot monitor it.
ACTIVE TEST
Operation Procedure
1.
Touch “HEAD LAMP” on “SELECT TEST ITEM” screen.
2.
Touch “ACTIVE TEST” on “SELECT DIAG MODE” screen.
3.
Touch item to be tested and check operation of the selected item.
4.
During the operation check, touching “BACK” deactivates the operation.
Display Item List
Headlamp High Beam Does Not Illuminate (Both Sides)
AKS007LW
1.
HEADLAMP ACTIVE TEST
1.
Select “HEAD LAMP (HI)” during active test. Refer to
.
2.
Make sure headlamp high beam operation.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 2.
Monitor item
Contents
IGN ON SW
“ON/OFF”
Displays “IGN position (ON)/OFF, ACC position (OFF)” judged from the ignition switch sig-
nal.
ACC ON SW
“ON/OFF”
Displays “ACC (ON)/OFF, Ignition OFF (OFF)” status judged from ignition switch signal.
AUTO LIGHT SW
Note
“ON/OFF”
Displays status of the lighting switch as judged from the lighting switch signal. (AUTO posi-
tion: ON/Other than AUTO position: OFF)
TAIL LAMP SW
“ON/OFF”
Displays status (lighting switch 1st position: ON/Others: OFF) of lighting switch judged
from lighting switch signal.
HEAD LAMP SW 1
“ON/OFF”
Displays status (headlamp switch 1: ON/Others: OFF) of headlamp switch 1 judged from
lighting switch signal.
HI BEAM SW
“ON/OFF”
Displays status (high beam switch: ON/Others: OFF) of high beam switch judged from
lighting switch signal.
PASSING SW
“ON/OFF”
Displays status (flash-to-pass switch: ON/Others: OFF) of flash-to-pass switch judged from
lighting switch signal.
FR FOG SW
“ON/OFF”
Displays status (front fog lamp switch: ON/Others: OFF) of front fog lamp switch judged
from lighting switch signal.
DOOR SW - DR
“ON/OFF”
Displays status of the driver door as judged from the driver door switch signal. (Door is
open: ON/Door is closed: OFF)
DOOR SW - AS
“ON/OFF”
Displays status of the passenger door as judged from the passenger door switch signal.
(Door is open: ON/Door is closed: OFF)
DOOR SW - RR
“ON/OFF”
Displays status of the rear doors as judged from the rear door switch signal. (Door is open:
ON/Door is closed: OFF)
HEAD LAMP SW 2
“ON/OFF”
Displays status (headlamp switch 2: ON/Others: OFF) of headlamp switch 2 judged from
lighting switch signal.
OPTICAL SENSOR
[0 - 5V]
Displays “ambient light (close to 5V when light/close to 0V when dark)” judged from optical
sensor signal.
Test item
Description
TAIL LAMP
Allows tail lamp relay to operate by switching ON–OFF.
HEAD LAMP (LOW)
Allows headlamp relay to operate by switching ON
−
OFF.
HEAD LAMP (HI)
Allows headlamp relay to operate by switching ON–OFF.
FR FOG LAMP
Allows fog lamp relay to operate by switching ON–OFF.
Headlamp high beam should operate.
LT-92
HEADLAMP -CONVENTIONAL TYPE-
Revision; 2004 April
2003 Murano
2.
CHECK HEADLAMP CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector and front combination lamp RH
and LH connector.
3.
Check continuity between IPDM E/R harness connector E7 ter-
minal 24 (L/W) and front combination lamp RH harness connec-
tor E30 terminal 1 (L/W).
4.
Check continuity between IPDM E/R harness connector E7 ter-
minal 22 (G) and front combination lamp LH harness connector
E17 terminal 1 (G).
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness or connector.
3.
CHECK HEADLAMP INPUT SIGNAL
1.
Connect IPDM E/R connector.
2.
Select “HEAD LAMP (HI)” during active test. Refer to
. When headlamp high beam is operating,
check voltage between front combination lamp RH and LH har-
ness connector and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Replace IPDM E/R.
4.
CHECK HEADLAMP GROUND
1.
Turn ignition switch OFF.
2.
Check continuity between front combination lamp RH harness
connector E30 terminal 5 (B/W) and ground.
3.
Check continuity between front combination lamp LH harness
connector E17 terminal 5 (B/W) and ground.
OK or NG
OK
>> Check headlamp bulb.
NG
>> Repair harness or connector.
Continuity should exist.
Continuity should exist.
SKIA4183E
Terminals
Voltage
(+)
(-)
Connector
Terminal
(Wire color)
RH
E30
1 (L/W)
Ground Battery
voltage
LH
E17
1 (G)
SKIA4184E
Continuity should exist.
Continuity should exist.
SKIA4188E
HEADLAMP -CONVENTIONAL TYPE-
LT-93
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision; 2004 April
2003 Murano
5.
CHECK COMBINATION SWITCH CIRCUIT
Select “BCM” on CONSULT-II. Carry out “BCM C/U” self-diagnosis.
Displayed results of self-diagnosis
No malfunction detected>> GO TO 6.
CAN communications or CAN system>> Check BCM CAN commu-
nication system. Refer to
tion Inspection Using CONSULT-II (Self-Diagnosis)"
OPEN DETECT 1 - 5>> Combination switch system malfunction.
Refer to
LT-257, "Combination Switch Inspection
According to Self-Diagnostic Results"
.
6.
CHECK COMBINATION SWITCH INPUT SIGNAL
Select “BCM” on CONSULT-II. With “HEAD LAMP” data monitor,
make sure “HI BEAM SW” turns ON-OFF linked with operation of
lighting switch.
OK or NG
OK
>> Replace BCM. Refer to
BCS-36, "Removal and Installa-
NG
>> Replace lighting switch.
Headlamp High Beam Does Not Illuminate (One Side)
AKS007LX
1.
CHECK BULB
Inspect bulbs of lamps which do not illuminate.
OK or NG
OK
>> GO TO 2.
NG
>> Replace headlamp bulb.
2.
CHECK HEADLAMP CIRCUIT
1.
Disconnect IPDM E/R connector and front combination lamp RH
or LH connector.
2.
Check continuity between IPDM E/R harness connector E7 ter-
minal 24 (L/W) and front combination lamp RH harness connec-
tor E30 terminal 1 (L/W).
3.
Check continuity between IPDM E/R harness connector E7 ter-
minal 22 (G) and front combination lamp LH harness connector
E17 terminal 1 (G).
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness or connector.
LKIA0073E
When lighting switch is
HIGH position
: HI BEAM SW ON
SKIA4193E
Continuity should exist.
Continuity should exist.
SKIA4183E
LT-94
HEADLAMP -CONVENTIONAL TYPE-
Revision; 2004 April
2003 Murano
3.
CHECK HEADLAMP GROUND
1.
Check continuity between front combination lamp RH harness
connector E30 terminal 5 (B/W) and ground.
2.
Check continuity between front combination lamp LH harness
connector E17 terminal 5 (B/W) and ground.
OK or NG
OK
>> Replace IPDM E/R.
NG
>> Repair harness or connector.
High Beam Indicator Lamp Does Not Illuminate
AKS007LY
1.
CHECK BULB
Inspect bulb of high beam indicator lamp.
OK or NG
OK
>> Replace combination meter.
NG
>> Replace indicator bulb.
Headlamp Low Beam Does Not Illuminate (Both Sides)
AKS007LZ
1.
HEADLAMP ACTIVE TEST
1.
Select “HEAD LAMP (LOW)” during active test. Refer to
.
2.
Make sure headlamp low beam operation.
OK or NG
OK
>> GO TO 5.
NG
>> GO TO 2.
2.
CHECK HEADLAMP CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector and front combination lamp RH
and LH connector.
3.
Check continuity between IPDM E/R harness connector E7 ter-
minal 27 (R/Y) and front combination lamp RH harness connec-
tor E30 terminal 4 (R/Y).
4.
Check continuity between IPDM E/R harness connector E7 ter-
minal 21 (L) and front combination lamp LH harness connector
E17 terminal 4 (L).
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness or connector.
Continuity should exist.
Continuity should exist.
SKIA4188E
Headlamp low beam should operate.
Continuity should exist.
Continuity should exist.
SKIA4186E
HEADLAMP -CONVENTIONAL TYPE-
LT-95
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision; 2004 April
2003 Murano
3.
CHECK HEADLAMP INPUT SIGNAL
1.
Connect IPDM E/R connector.
2.
Select “HEAD LAMP (LOW)” during active test. Refer to
. When headlamp low beam is operating, check
voltage between front combination lamp LH and RH harness
connector and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Replace IPDM E/R.
4.
CHECK HEADLAMP GROUND
1.
Turn ignition switch OFF.
2.
Check continuity between front combination lamp RH harness
connector E30 terminal 5 (B/W) and ground.
3.
Check continuity between front combination lamp LH harness
connector E17 terminal 5 (B/W) and ground.
OK or NG
OK
>> Check headlamp bulb.
NG
>> Repair harness or connector.
5.
CHECK COMBINATION SWITCH CIRCUIT
Select “BCM” on CONSULT-II. Carry out “BCM C/U” self-diagnosis.
Displayed results of self-diagnosis
No malfunction detected>> GO TO 6.
CAN communication or CAN system>> Check BCM CAN commu-
nication system. Refer to
tion Inspection Using CONSULT-II (Self-Diagnosis)"
OPEN DETECT 1 - 5>> Combination Switch System malfunction.
Refer to
LT-257, "Combination Switch Inspection
According to Self-Diagnostic Results"
.
HEAD LAMP SW 1 or HEAD LAMP SW 2>>
Replace
lighting
switch.
Terminals
Voltage
(+)
(-)
Connector
Terminal
(Wire color)
RH
E30
4 (R/Y)
Ground Battery
voltage
LH
E17
4 (L)
SKIA4187E
Continuity should exist.
Continuity should exist.
SKIA4188E
LKIA0073E
LT-96
HEADLAMP -CONVENTIONAL TYPE-
Revision; 2004 April
2003 Murano
6.
CHECK COMBINATION SWITCH INPUT SIGNAL
Select “BCM” on CONSULT-II. With “HEAD LAMP” data monitor,
make sure “HEAD LAMP SW 1” and “HEAD LAMP SW 2” turn ON-
OFF with operation of lighting switch.
OK or NG
OK
>> Replace BCM. Refer to
BCS-36, "Removal and Installa-
NG
>>
●
Replace lighting switch.
●
If one of “HEAD LAMP SW 1”and “HEAD LAMP SW
2” is NG, replace both BCM (Refer to
"Removal and Installation of BCM"
) and lighting switch.
Headlamp Low Beam Does Not Illuminate (One Side)
AKS007M0
1.
CHECK BULB
Inspect bulbs of lamps which do not illuminate.
OK or NG
OK
>> GO TO 2.
NG
>> Replace headlamp bulb.
2.
CHECK HEADLAMP CIRCUIT
1.
Disconnect IPDM E/R connector and front combination lamp RH
or LH connector.
2.
Check continuity between IPDM E/R harness connector E7 ter-
minal 27 (R/Y) and front combination lamp RH harness connec-
tor E30 terminal 4 (R/Y).
3.
Check continuity between IPDM E/R harness connector E7 ter-
minal 21 (L) and front combination lamp LH harness connector
E17 terminal 4 (L).
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness or connector.
3.
CHECK HEADLAMP GROUND
1.
Check continuity between front combination lamp RH harness
connector E30 terminal 5 (B/W) and ground.
2.
Check continuity between front combination lamp LH harness
connector E17 terminal 5 (B/W) and ground.
OK or NG
OK
>> Replace IPDM E/R.
NG
>> Repair harness or connector.
When lighting switch is 2ND
position
: HEAD LAMP SW 1 ON
: HEAD LAMP SW 2 ON
SKIA4194E
Continuity should exist.
Continuity should exist.
SKIA4186E
Continuity should exist.
Continuity should exist.
SKIA4188E
HEADLAMP -CONVENTIONAL TYPE-
LT-97
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision; 2004 April
2003 Murano
Headlamp RH Low Beam and High Beam Does Not Illuminate
AKS007M2
1.
CHECK BULB
Inspect bulbs of lamps which do not illuminate.
OK or NG
OK
>> GO TO 2.
NG
>> Replace headlamp bulb.
2.
CHECK HEADLAMP GROUND
1.
Disconnect front combination lamp RH connector.
2.
Check continuity between front combination lamp RH harness
connector E30 terminal 5 (B/W) and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness or connector.
3.
CHECK HEADLAMP CIRCUIT
1.
Disconnect IPDM E/R connector.
2.
Check continuity between IPDM E/R harness connector E7 ter-
minal 27 (R/Y) and front combination lamp RH harness connec-
tor E30 terminal 4 (R/Y).
3.
Check continuity between IPDM E/R harness connector E7 ter-
minal 24 (L/W) and front combination lamp RH harness connec-
tor E30 terminal 1 (L/W).
OK or NG
OK
>> Replace IPDM E/R.
NG
>> Repair harness or connector.
Headlamp LH Low Beam and High Beam Does Not Illuminate
AKS007M1
1.
CHECK BULB
Inspect bulbs of lamps which do not illuminate.
OK or NG
OK
>> GO TO 2.
NG
>> Replace headlamp bulb.
Continuity should exist.
SKIA4188E
Continuity should exist.
SKIA4191E
Continuity should exist.
SKIA4192E
LT-98
HEADLAMP -CONVENTIONAL TYPE-
Revision; 2004 April
2003 Murano
2.
CHECK HEADLAMP GROUND
1.
Disconnect front combination lamp LH connector.
2.
Check continuity between front combination lamp LH harness
connector E17 terminal 5 (B/W) and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness or connector.
3.
CHECK HEADLAMP CIRCUIT
1.
Disconnect IPDM E/R connector.
2.
Check continuity between IPDM E/R harness connector E7 ter-
minal 21 (L) and front combination lamp LH harness connector
E17 terminal 4 (L).
3.
Check continuity between IPDM E/R harness connector E7 ter-
minal 22 (G) and front combination lamp LH harness connector
E17 terminal 1 (G).
OK or NG
OK
>> Replace IPDM E/R.
NG
>> Repair harness or connector.
Headlamps Do Not Turn OFF
AKS007M3
1.
CHECK HEADLAMP TURN OFF
Make sure that lighting switch is OFF. And make sure is headlamp turns off when ignition switch is turned OFF.
OK or NG
OK
>> GO TO 3
NG
>> GO TO 2
Continuity should exist.
SKIA4188E
Continuity should exist.
SKIA4189E
Continuity should exist.
SKIA4190E
HEADLAMP -CONVENTIONAL TYPE-
LT-99
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision; 2004 April
2003 Murano
2.
CHECK COMBINATION SWITCH INPUT SIGNAL
Select “BCM” on CONSULT-II. With “HEAD LAMP” data monitor,
make sure “HEAD LAMP SW 1” and “HEAD LAMP SW 2” turns ON-
OFF linked with operation of lighting switch.
OK or NG
OK
>> Replace IPDM E/R.
NG
>> Replace lighting switch.
3.
CHECKING CAN COMMUNICATIONS BETWEEN BCM AND IPDM E/R
IPDM E/R detects CAN communication malfunction and activates fail-safe operation. Refer to
Communication Inspection Using CONSULT-II (Self-Diagnosis)"
OK or NG
OK
>> Replace IPDM E/R.
NG
>> Repair malfunctioning part.
Aiming Adjustment
AKS007M4
PREPARATION BEFORE ADJUSTING
For details, refer to the regulations in your own country.
Before performing aiming adjustment, check the following.
1.
Keep all tires inflated to correct pressures.
2.
Place vehicle on flat surface.
3.
Set that there is no-load in vehicle other than the driver (or equivalent weight placed in driver's position).
Coolant, engine oil filled up to correct level and full fuel tank.
When lighting switch is OFF
position
: HEAD LAMP SW 1 OFF
: HEAD LAMP SW 2 OFF
SKIA5200E
PKIA2515E
LT-100
HEADLAMP -CONVENTIONAL TYPE-
Revision; 2004 April
2003 Murano
LOW BEAM AND HIGH BEAM
1.
Turn headlamp low beam ON.
2.
Use adjusting screws to perform aiming adjustment.
ADJUSTMENT USING AN ADJUSTMENT SCREEN (LIGHT/DARK BORDERLINE)
If the vehicle front body has been repaired and/or the headlamp assembly has been replaced, check aiming.
Use the aiming chart shown in the figure.
●
Basic illumination area for adjustment should be within the range shown on the aiming chart.
Adjust headlamp accordingly.
Bulb Replacement
AKS007M5
HEADLAMP HIGH/LOW BEAM
1.
Turn lighting switch OFF.
2.
Remove fender protector (front). Refer to
3.
Turn plastic cap counterclockwise and unlock it.
4.
Disconnect bulb terminal.
5.
Unlock retaining spring and remove bulb from headlamp.
6.
Install in reverse order of removal.
PARKING LAMP (CLEARANCE LAMP)
1.
Turn lighting switch OFF.
2.
Remove air cleaner case (when replacing LH bulb). Refer to
EM-14, "AIR CLEANER AND AIR DUCT"
in
“EM” section.
3.
Remove IPDM E/R (when replacing RH bulb). Refer to
PG-46, "Removal and Installation of IPDM E/R"
in
“PG” section.
4.
Turn bulb socket counterclockwise and unlock it.
PKIA3034E
Headlamp high/low beam
(Halogen)
: 12V - 65/55W (HB5)
HEADLAMP -CONVENTIONAL TYPE-
LT-101
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision; 2004 April
2003 Murano
5.
Remove bulb from its socket.
6.
Install in the reverse order of removal.
FRONT TURN SIGNAL LAMP
1.
Turn lighting switch OFF.
2.
Remove fender protector (front). Refer to
3.
Turn bulb socket counterclockwise and unlock it.
4.
Remove bulb from its socket.
5.
Install in the reverse order of removal.
CAUTION:
After installing bulb, be sure to install plastic cap and bulb socket securely to insure watertightness.
FRONT SIDE MARKER LAMP
1.
Turn lighting switch OFF.
2.
Remove fender protector (front). Refer to
3.
Turn bulb socket counterclockwise and unlock it.
4.
Remove bulb from its socket.
5.
Install in the reverse order of removal.
CAUTION:
After installing bulb, be sure to install plastic cap and socket securely to insure watertightness.
Removal and Installation
AKS007M6
REMOVAL
1.
Remove front bumper. Refer to
in
“EI” section.
2.
Remove headlamp mounting bolts.
3.
Remove plastics bumper bracket, then pull headlamp toward
vehicle front, disconnect connector, and remove headlamp.
INSTALLATION
Note the following, and install in the reverse order of removal.
NOTE:
After installation, perform aiming adjustment. Refer to
.
Parking lamps (Clearance lamps)
: 12V - 3.8W
Front turn signal lamp
: 12V - 21W (amber)
Front side marker lamp
: 12V - 3.8W
PKIA2519E
Headlamp mounting bolt
: 6.1 N·m (0.62 kg-m, 54 in-lb)
LT-102
HEADLAMP -CONVENTIONAL TYPE-
Revision; 2004 April
2003 Murano
Disassembly and Assembly
AKS007M7
DISASSEMBLY
1.
Disconnect the connector to the halogen bulb (high/low).
2.
Turn plastic holder counterclockwise and unlock it.
3.
Disconnect bulb socket.
4.
Unlock retaining spring, and remove halogen bulb (high/low).
5.
Turn parking lamp bulb socket counterclockwise and unlock it.
6.
Remove parking lamp bulb from its socket.
7.
Turn front turn signal lamp bulb socket counterclockwise and unlock it.
8.
Remove front turn signal lamp bulb from its socket.
9.
Turn front side marker lamp bulb socket counterclockwise and unlock it
10. Remove front side lamp marker lamp bulb from its socket.
ASSEMBLY
Note the following, and assemble in the reverse order of disassemble.
CAUTION:
●
After installing bulb, be sure to install plastic cap and bulb socket securely to insure watertight-
ness.
PKIA2518E
1.
Side marker lamp bulb
2.
Side marker lamp bulb socket
3.
Halogen bulb connector
4.
Front turn signal lamp bulb
5.
Front turn signal lamp bulb socket
6.
Plastic holder
7.
Halogen bulb
8.
Parking lamp (clearance lamp) bulb
socket
9.
Parking lamp (clearance lamp) bulb
10. Headlamp housing assembly
DAYTIME LIGHT SYSTEM
LT-103
C
D
E
F
G
H
I
J
L
M
A
B
LT
Revision; 2004 April
2003 Murano
DAYTIME LIGHT SYSTEM
PFP:284B2
Component Parts and Harness Connector Location
AKS007NE
System Description
AKS007NF
During a ran, when the engine which makes fog lamp turn on has started and parking brake is detached,
foglamp turns do daytime light system for the Canada vehicle, and the light is put out at the of operating park-
ing brake, and the of lighting switch 2ND position or the lighting switch AUTO (at the time of headlamp light-
ing).
ON/OFF of fog lamp switch is followed at the time of lighting switch 2ND position, and it is turned on and
switched off.
An parking brake signal and engine ran or stop signal are sent to BCM (body control module) by CAN commu-
nication line, and control daytime light system.
CAUTION:
If an ignition switch is turned ON within several seconds in OFF from the ignition switch ON in the
state of daytime light system lighting, daytime light system which put out the light once OFF form the
ignition switch ON will relight up for about 2 seconds.
In the state where the parking brake is not operated, if cranking time is extremely short daytime light
system will light up for about 2 seconds.
OUTLINE
Power is supplied at all times
●
through 15A fuse [No. 72, located in IPDM E/R (intelligent power distribution module engine room)]
●
to front fog lamp relay [located in IPDM E/R (intelligent power distribution module engine room)]
●
through 15A fuse [No. 73, located in IPDM E/R (intelligent power distribution module engine room)]
●
to CPU (central processing unit) [located in IPDM E/R (intelligent power distribution module engine room)]
Power is also supplied at all times
●
through 50A fusible link (letter F, located in fuse and fusible link block)
●
to BCM (body control module) terminal 7
When the ignition switch is in ON or START position, power is supplied
SKIA4598E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст