Nissan Murano Z50 (2003 year). Manual — part 165
LAN-254
[CAN]
CAN SYSTEM (TYPE 7)
Revision; 2004 April
2003 Murano
3.
CHECK HARNESS FOR SHORT CIRCUIT
Check continuity between data link connector M24 terminals 6 (L),
14 (Y) and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Check the following harnesses. If any harness is dam-
aged, repair the harness.
●
Harness between data link connector and ECM.
●
Harness between data link connector and harness
connector M82.
●
Harness between data link connector and display control unit.
●
Harness between data link connector and BCM.
●
Harness between data link connector and unified meter and A/C amp.
●
Harness between data link connector and harness connector M9.
4.
CHECK HARNESS FOR SHORT CIRCUIT
1.
Disconnect TCM connector.
2.
Check continuity between TCM harness connector F103 termi-
nals 5 (L) and 6 (Y).
OK or NG
OK
>> GO TO 5.
NG
>> Repair harness between TCM and harness connector
F102.
5.
CHECK HARNESS FOR SHORT CIRCUIT
Check continuity between TCM harness connector F103 terminals 5
(L), 6 (Y) and ground.
OK or NG
OK
>> GO TO 6.
NG
>> Repair harness between TCM and harness connector
F102.
6 (L) - Ground
: Continuity should not exist.
14 (Y) - Ground
: Continuity should not exist.
PKIA2079E
5 (L) - 6 (Y)
: Continuity should not exist.
PKIA0817E
5 (L) - Ground
: Continuity should not exist.
6 (Y) - Ground
: Continuity should not exist.
SKIA5020E
CAN SYSTEM (TYPE 7)
LAN-255
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision; 2004 April
2003 Murano
6.
CHECK HARNESS FOR SHORT CIRCUIT
1.
Disconnect harness connector B4 and harness connector B9.
2.
Check continuity between harness connector B4 terminals 3 (L)
and 10 (Y).
OK or NG
OK
>> GO TO 7.
NG
>> Check the following harnesses. If any harness is dam-
aged, repair the harness.
●
Repair harness between harness connector B4 and
harness connector B2.
●
Repair harness between harness connector B4 and
harness connector B9.
7.
CHECK HARNESS FOR SHORT CIRCUIT
Check continuity between harness connector B4 terminals 3 (L), 10
(Y) and ground.
OK or NG
OK
>> GO TO 8.
NG
>> Check the following harnesses. If any harness is dam-
aged, repair the harness.
●
Repair harness between harness connector B4 and
harness connector B2.
●
Repair harness between harness connector B4 and harness connector B9.
8.
CHECK HARNESS FOR SHORT CIRCUIT
1.
Disconnect driver seat control unit connector.
2.
Check continuity between driver seat control unit harness con-
nector B303 terminals 3 (L/Y) and 19 (BR/W).
OK or NG
OK
>> GO TO 9.
NG
>> Repair harness between driver seat control unit and har-
ness connector B301.
3 (L) - 10 (Y)
: Continuity should not exist.
SKIA5021E
3 (L) - Ground
: Continuity should not exist.
10 (Y) - Ground
: Continuity should not exist.
SKIA5022E
3 (L/Y) - 19 (BR/W)
: Continuity should not exist.
SKIA5024E
LAN-256
[CAN]
CAN SYSTEM (TYPE 7)
Revision; 2004 April
2003 Murano
9.
CHECK HARNESS FOR SHORT CIRCUIT
Check continuity between driver seat control unit harness connector
B303 terminals 3 (L/Y), 19 (BR/W) and ground.
OK or NG
OK
>> GO TO 10.
NG
>> Repair harness between driver seat control unit and har-
ness connector B301.
10.
CHECK HARNESS FOR SHORT CIRCUIT
1.
Disconnect ABS actuator and electric unit (control unit) connector and IPDM E/R connector.
2.
Check continuity between IPDM E/R harness connector E9 ter-
minals 48 (L) and 49 (Y).
OK or NG
OK
>> GO TO 11.
NG
>> Check the following harnesses. If any harness is dam-
aged, repair the harness.
●
Harness between IPDM E/R and ABS actuator and
electric unit (control unit).
●
Harness between IPDM E/R and harness connector
E105.
11.
CHECK HARNESS FOR SHORT CIRCUIT
Check continuity between IPDM E/R harness connector E9 termi-
nals 48 (L), 49 (Y) and ground.
OK or NG
OK
>> GO TO 12.
NG
>> Check the following harnesses. If any harness is dam-
aged, repair the harness.
●
Harness between IPDM E/R and ABS actuator and
electric unit (control unit).
●
Harness between IPDM E/R and harness connector E105.
12.
ECM/IPDM E/R INTERNAL CIRCUIT INSPECTION
Check components inspection. Refer to
LAN-257, "ECM/IPDM E/R INTERNAL CIRCUIT INSPECTION"
OK or NG
OK
>> Connect all the connectors and diagnose again. Refer to
.
NG
>> Replace ECM and/or IPDM E/R.
IPDM E/R Ignition Relay Circuit Check
AKS006SH
Check the following. If no malfunction is found, replace the IPDM E/R.
●
IPDM E/R power supply circuit. Refer to
PG-45, "IPDM E/R Power/Ground Circuit Inspection"
.
●
Ignition power supply circuit. Refer to
PG-10, "IGNITION POWER SUPPLY - IGNITION SW. IN “ON”
3 (L/Y) - Ground
: Continuity should not exist.
19 (BR/W) - Ground
: Continuity should not exist.
SKIA5025E
48 (L) - 49 (Y)
: Continuity should not exist.
LKIA0030E
48 (L) - Ground
: Continuity should not exist.
49 (Y) - Ground
: Continuity should not exist.
LKIA0036E
CAN SYSTEM (TYPE 7)
LAN-257
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision; 2004 April
2003 Murano
Component Inspection
AKS006SI
ECM/IPDM E/R INTERNAL CIRCUIT INSPECTION
●
Remove ECM and IPDM E/R from vehicle.
●
Check resistance between ECM terminals 94 and 86.
●
Check resistance between IPDM E/R terminals 48 and 49.
Unit
Terminal
Resistance value (
Ω
)
(Approx.)
ECM
94 - 86
108 - 132
IPDM E/R
48 - 49
LKIA0037E
LAN-258
[CAN]
CAN SYSTEM (TYPE 8)
Revision; 2004 April
2003 Murano
CAN SYSTEM (TYPE 8)
PFP:23710
System Description
AKS006SJ
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
Component Parts and Harness Connector Location
AKS006SK
SKIA5864E
CAN SYSTEM (TYPE 8)
LAN-259
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision; 2004 April
2003 Murano
Schematic
AKS006SL
TKWA0951E
LAN-260
[CAN]
CAN SYSTEM (TYPE 8)
Revision; 2004 April
2003 Murano
Wiring Diagram - CAN -
AKS006SM
TKWA0952E
CAN SYSTEM (TYPE 8)
LAN-261
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision; 2004 April
2003 Murano
TKWA0953E
LAN-262
[CAN]
CAN SYSTEM (TYPE 8)
Revision; 2004 April
2003 Murano
TKWA0954E
CAN SYSTEM (TYPE 8)
LAN-263
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision; 2004 April
2003 Murano
Work Flow
AKS00C50
1.
When there are no indications of “TRANSMISSION”, “AIR PRESSURE MONITOR”, “METER A/C AMP”
or “AUTO DRIVE POS.” on “SELECT SYSTEM” display of CONSULT-II, print the “SELECT SYSTEM”.
2.
Print all the data of “SELF-DIAG RESULTS” for “ENGINE”, “TRANSMISSION”, “AIR PRESSURE MONI-
TOR”, “BCM”, “METER A/C AMP”, “AUTO DRIVE POS.” and “ABS” displayed on CONSULT-II.
3.
Print all the data of “CAN DIAG SUPPORT MNTR” for “ENGINE”, “TRANSMISSION”, “AIR PRESSURE
MONITOR”, “BCM”, “METER A/C AMP”, “AUTO DRIVE POS.” and “ABS” displayed on CONSULT-II.
4.
Attach the printed sheet of “SELECT SYSTEM”, “SELF-DIAG RESULTS” and “CAN DIAG SUPPORT
MNTR” onto the check sheet. Refer to
5.
Based on the indications of “SELECT SYSTEM” and the results of “CAN DIAG SUPPORT MNTR”, put
marks “v” onto the items with “No indication”, “NG”, or “UNKWN” in the check sheet table. Refer to
NOTE:
●
If “NG” is displayed on “INITIAL DIAG (Initial diagnosis)” as “CAN DIAG SUPPORT MNTR” for the diag-
nosed control unit, replace the control unit.
●
The “CAN DIAG SUPPORT MNTR” items, which are not in check sheet table, are not related to diag-
nostic procedure on service manual.
So it is not necessary to check the status of “CAN DIAG SUPPORT MNTR” items which are not indi-
cated in check sheet table.
6.
Check CAN communication line of the navigation system. Refer to
AV-203, "CAN Communication Line
.
7.
Attach the CAN DIAG SUPPORT MONITOR check sheet onto the check sheet. Refer to
PKIA2093E
PKIA8260E
PKIA8343E
LAN-264
[CAN]
CAN SYSTEM (TYPE 8)
Revision; 2004 April
2003 Murano
8.
Mark the “NG” or “UNKWN” item of the check sheet table with “v” from the result of CAN DIAG SUPPORT
MONITOR check sheet. Refer to
.
NOTE:
If “NG” is displayed on “CAN COMM” as “CAN DIAG SUPPORT MONITOR” for the diagnosed control
unit, replace the control unit. Refer to
AV-203, "CAN Communication Line Check"
9.
According to the check sheet results (example), start inspection. Refer to
.
CAN SYSTEM (TYPE 8)
LAN-265
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision; 2004 April
2003 Murano
CHECK SHEET
NOTE:
If “NG” is displayed on “INITIAL DIAG (Initial diagnosis)” or “CAN COMM” for the diagnosed control unit,
replace the control unit.
PKIB0531E
LAN-266
[CAN]
CAN SYSTEM (TYPE 8)
Revision; 2004 April
2003 Murano
PKIB0498E
CAN SYSTEM (TYPE 8)
LAN-267
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision; 2004 April
2003 Murano
CHECK SHEET RESULTS (EXAMPLE)
NOTE:
If “NG” is displayed on “INITIAL DIAG (Initial diagnosis)” or “CAN COMM” for the diagnosed control unit,
replace the control unit.
Case 1
Check harness between TCM and data link connector. Refer to
LAN-281, "Circuit Check Between TCM and
PKIB0532E
SKIA5187E
LAN-268
[CAN]
CAN SYSTEM (TYPE 8)
Revision; 2004 April
2003 Murano
Case 2
Check harness between data link connector and driver seat control unit. Refer to
Between Data Link Connector and Driver Seat Control Unit"
.
PKIB0533E
SKIA5188E
CAN SYSTEM (TYPE 8)
LAN-269
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
Revision; 2004 April
2003 Murano
Case 3
Check harness between driver seat control unit and ABS actuator and electric unit (control unit). Refer to
.
PKIB0534E
SKIA5189E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст