Nissan Murano Z50 (2003 year). Manual — part 10
TROUBLE DIAGNOSIS
ATC-123
C
D
E
F
G
H
I
K
L
M
A
B
ATC
Revision; 2004 April
2003 Murano
COMPONENT INSPECTION
Sunload Sensor
Measure voltage between unified meter and A/C amp. harness con-
nector M51 terminal 50 (O) and ground.
If NG, replace sunload sensor.
●
When checking sunload sensor, select a place where sun shines directly on it.
RJIA1807E
SHA930E
ATC-124
TROUBLE DIAGNOSIS
Revision; 2004 April
2003 Murano
Intake Sensor Circuit
AJS00114
COMPONENT DESCRIPTION
Intake Sensor
The intake sensor is located on the heater & cooling unit. It converts
temperature of air after it passes through the evaporator into a resis-
tance value which is then input to the unified meter and A/C amp.
DIAGNOSTIC PROCEDURE FOR INTAKE SENSOR
SYMPTOM: Intake sensor circuit is open or shorted. (24 or
−
24 is
indicated on unified meter and A/C amp. as a result of performing
Self-diagnosis STEP-2.)
1.
CHECK VOLTAGE BETWEEN INTAKE SENSOR AND GROUND
1.
Disconnect intake sensor connector.
2.
Turn ignition switch ON.
3.
Check voltage between intake sensor harness connector M256
terminal 1 (R/W) and ground.
OK or NG
OK
>> GO TO 2.
NG
>> GO TO 4.
2.
CHECK CIRCUIT CONTINUITY BETWEEN INTAKE SENSOR AND UNIFIED METER AND A/C AMP.
1.
Turn ignition switch OFF.
2.
Disconnect unified meter and A/C amp. connector.
3.
Check continuity between intake sensor harness connector
M256 terminal 2 (B/Y) and unified meter and A/C amp. harness
connector M51 terminal 49 (B/Y).
OK or NG
OK
>> GO TO 3.
NG
>> Repair harness or connector.
RJIA1808E
RJIA1458E
1 – Ground
: Approx. 5V
RJIA1809E
2 – 49
: Continuity should exist.
RJIA1810E
TROUBLE DIAGNOSIS
ATC-125
C
D
E
F
G
H
I
K
L
M
A
B
ATC
Revision; 2004 April
2003 Murano
3.
CHECK INTAKE SENSOR
Refer to
OK or NG
OK
>> 1. Replace unified meter and A/C amp.
2. Go to self-diagnosis
ATC-69, "FUNCTION CONFIRMATION PROCEDURE"
and perform self-
diagnosis STEP-2. Confirm that code No. 20 is displayed.
NG
>> 1. Replace intake sensor.
2. Go to self-diagnosis
ATC-69, "FUNCTION CONFIRMATION PROCEDURE"
and perform self-
diagnosis STEP-2. Confirm that code No. 20 is displayed.
4.
CHECK CIRCUIT CONTINUITY BETWEEN INTAKE SENSOR AND UNIFIED METER AND A/C AMP.
1.
Turn ignition switch OFF.
2.
Disconnect unified meter and A/C amp. connector.
3.
Check continuity between intake sensor harness connector
M256 terminal 1 (R/W) and unified meter and A/C amp. harness
connector M51 terminal 41 (R/Y).
4.
Check continuity between intake sensor harness connector
M256 terminal 1 (R/W) and ground.
OK or NG
OK
>> 1. Replace unified meter and A/C amp.
2. Go to self-diagnosis
ATC-69, "FUNCTION CONFIRMATION PROCEDURE"
and perform self-
diagnosis STEP-2. Confirm that code No. 20 is displayed.
NG
>> Repair harness or connector.
COMPONENT INSPECTION
Intake Sensor
After disconnecting intake sensor connector, measure resistance
between terminals 1 and 2 at sensor harness side, using the table
below.
If NG, replace intake sensor.
1 – 41
: Continuity should exist.
1 – Ground
: Continuity should not exist.
RJIA1811E
Temperature
°
C (
°
F)
Resistance k
Ω
−
15 (5)
18.63
−
10 (14)
14.14
−
5 (23)
10.85
0 (32)
8.40
5 (41)
6.57
10 (50)
5.18
15 (59)
4.12
20 (68)
3.30
25 (77)
2.66
30 (86)
2.16
35 (95)
1.77
40 (104)
1.46
45 (113)
1.21
RJIA1812E
ATC-126
CONTROLLER
Revision; 2004 April
2003 Murano
CONTROLLER
PFP:27500
Removal and Installation of A/C and AV Switch
AJS000ZN
REMOVAL
Refer to
AV-57, "Removal and Installation for A/C and AV Switch"
INSTALLATION
Installation is basically the reverse order of removal.
AUTO AMP
ATC-127
C
D
E
F
G
H
I
K
L
M
A
B
ATC
Revision; 2004 April
2003 Murano
AUTO AMP
PFP:27760
Removal and Installation of Unified Meter and A/C Amp.
AJS000ZP
REMOVAL
1.
Remove A/C and AV switch from audio unit. Refer to
"Removal and Installation for A/C and AV Switch"
.
2.
Remove the fixing screws, then remove the unified meter and A/
C amp.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA1813E
ATC-128
AMBIENT SENSOR
Revision; 2004 April
2003 Murano
AMBIENT SENSOR
PFP:27722
Removal and Installation
AJS000ZR
REMOVAL
1.
Remove ambient sensor from bracket.
2.
Disconnect ambient sensor connector, then remove it.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA1800E
IN-VEHICLE SENSOR
ATC-129
C
D
E
F
G
H
I
K
L
M
A
B
ATC
Revision; 2004 April
2003 Murano
IN-VEHICLE SENSOR
PFP:27720
Removal and Installation
AJS000ZS
REMOVAL
1.
Remove instrument driver lower panel. Refer to
2.
Remove in-vehicle sensor.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA1814E
ATC-130
SUNLOAD SENSOR
Revision; 2004 April
2003 Murano
SUNLOAD SENSOR
PFP:27721
Removal and Installation
AJS000ZT
REMOVAL
1.
Remove instrument mask (right side). Refer to
.
2.
Disconnect sunload sensor connector, then remove sunload
sensor.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA1806E
INTAKE SENSOR
ATC-131
C
D
E
F
G
H
I
K
L
M
A
B
ATC
Revision; 2004 April
2003 Murano
INTAKE SENSOR
PFP:27723
Removal and Installation
AJS000ZU
REMOVAL
1.
Set the temperature at 18
°
C (60
°
F), and then disconnect the battery negative cable.
2.
Use a refrigerant collecting equipment (for HFC-134a) to discharge refrigerant.
3.
Remove cowl top cover. Refer to
4.
Remove high-pressure pipe 1 fixing clip.
5.
Remove low-pressure flexible hose fixing bolt.
6.
Disconnect evaporator-side one-touch joints.
a.
Set a disconnector (High-pressure side: 92530-89908, Low-
pressure side: 92530-89916) on A/C piping.
b.
Slide a disconnector toward vehicle front until it clicks.
c.
Slide A/C piping toward vehicle front and disconnect it.
CAUTION:
Seal connection opening of piping with a cap or vinyl tape
to avoid exposure to atmosphere.
7.
Remove blower unit. Refer to
.
8.
Remove air mix door motor (Passenger side).
9.
Remove intake sensor connector, foot duct and heater core
cover.
10. Remove evaporator cover from heater & cooling unit.
11. Remove the fixing bolt, then remove the low-pressure pipe 2
and high-pressure pipe 2.
CAUTION:
Seal connection opening of piping with a cap or vinyl tape
to avoid exposure to atmosphere.
12. Slide the evaporator to passenger side, then remove the intake
sensor.
RJIA1815E
RJIA1816E
RJIA1817E
RJIA1808E
ATC-132
INTAKE SENSOR
Revision; 2004 April
2003 Murano
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
●
Replace O-rings for A/C piping with new ones. Before installing, apply compressor oil to them.
●
Connection point for female-side piping is thin. So, when inserting male-side piping, take care not
to deform female-side piping. Slowly insert in axial direction.
●
Insert one-touch joint connection point securely until it clicks.
●
After piping has been connected, pull male-side piping by hand to make sure piping does not
come off.
BLOWER UNIT
ATC-133
C
D
E
F
G
H
I
K
L
M
A
B
ATC
Revision; 2004 April
2003 Murano
BLOWER UNIT
PFP:27200
Removal and Installation
AJS000ZV
REMOVAL
1.
Remove instrument passenger lower panel. Refer to
2.
Remove ECM with bracket attached.
3.
Remove fixing nuts (2), then fixing bolts (2) and screw (1), then
remove blower unit.
CAUTION:
Move blower unit rightward, and remove locating pin (1)
and joint. Then remove blower unit downward.
4.
Disconnect intake door motor connector and blower fan motor
connector.
5.
Remove harness clips (2) from blower unit.
6.
Remove blower unit.
INSTALLATION
Installation is basically the reverse order of removal.
CAUTION:
Make sure locating pin (1) and joint are securely inserted.
RJIA1818E
RJIA1819E
ATC-134
BLOWER UNIT
Revision; 2004 April
2003 Murano
Disassembly and Assembly
AJS000ZW
CAUTION:
If retaining tabs are damaged while disassembling blower unit,
use 7 screws (27111-2Y000) to assemble blower unit.
1.
Intake adapter
2.
Intake box case
3.
Intake upper case
4.
Intake lower case
5.
Blower fan motor assembly
6.
Intake door motor
7.
In-cabin microfilter
8.
Filter cover
9.
Intake door 2
10. Intake door 1
11.
Intake door lever 1
12. Intake door link
13. Intake door lever 2
RJIA1820E
RJIA1821E
BLOWER MOTOR
ATC-135
C
D
E
F
G
H
I
K
L
M
A
B
ATC
Revision; 2004 April
2003 Murano
BLOWER MOTOR
PFP:27226
Removal and Installation
AJS000ZX
REMOVAL
1.
Remove instrument passenger lower panel. Refer to
2.
Disconnect blower motor connector.
3.
Remove screws from blower motor, then remove it.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA1822E
ATC-136
INTAKE DOOR MOTOR
Revision; 2004 April
2003 Murano
INTAKE DOOR MOTOR
PFP:27730
Removal and Installation
AJS000ZY
REMOVAL
1.
Remove blower unit. Refer to
2.
Remove intake door motor from the blower unit.
INSTALLATION
Installation is basically the reverse order of removal.
RJIA1823E
IN-CABIN MICROFILTER
ATC-137
C
D
E
F
G
H
I
K
L
M
A
B
ATC
Revision; 2004 April
2003 Murano
IN-CABIN MICROFILTER
PFP:27277
Removal and Installation
AJS000ZZ
FUNCTION
Air inside passenger compartment is kept clean at either recircula-
tion or fresh mode by installing in-cabin microfilter into blower unit.
REPLACEMENT TIMING
Replace in-cabin microfilter.
Refer to
MA-8, "CHASSIS AND BODY MAINTENANCE"
in SCHEDULE 1 and
in SCHEDULE 2.
Caution label is fixed inside the glove box.
REPLACEMENT PROCEDURES
1.
Remove the instrument passenger lower panel. Refer to
2.
Remove the filter cover, then remove the in-cabin microfilter.
3.
Take out the in-cabin microfilter from blower unit.
4.
Replace with new one and reinstall on blower unit.
5.
Reinstall the glove box.
RJIA1331E
RJIA1824E
ATC-138
HEATER & COOLING UNIT ASSEMBLY
Revision; 2004 April
2003 Murano
HEATER & COOLING UNIT ASSEMBLY
PFP:27110
Removal and Installation
AJS00100
REMOVAL
1.
Use a refrigerant collecting equipment (for HFC-134a) to discharge refrigerant.
2.
Drain coolant from cooling system. Refer to
CO-8, "Changing Engine Coolant"
3.
Remove cowl top cover. Refer to
4.
Disconnect evaporator-side one-touch joints.
a.
Set a disconnector (High-pressure side: 92530-89908, Low-
pressure side: 92530-89916) on A/C piping.
b.
Slide a disconnector toward vehicle front until it clicks.
c.
Slide A/C piping toward vehicle front and disconnect it.
CAUTION:
Seal connection opening of piping with a cap or vinyl tape
to avoid exposure to atmosphere.
5.
Disconnect two heater hoses from heater core.
6.
Remove instrument panel assembly. Refer to
.
7.
Remove blower unit. Refer to
8.
Remove clips of vehicle harness from steering member.
9.
Remove instrument stays (driver side and passenger side).
10. Renove rear ventilator duct1 and front floor duct. Refer to
147, "Removal of Rear Ventilator Ducts"
and
.
RJIA1815E
RJIA1825E
RJIA1826E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст