Nissan Murano Z50 (2003 year). Manual — part 123
REAR BUMPER
EI-17
C
D
E
F
G
H
J
K
L
M
A
B
EI
Revision; 2004 April
2003 Murano
REAR BUMPER
PFP:H5022
Removal and Installation
AIS002A4
CAUTION:
Bumper fascia is made of resin. Do not apply strong force to it, and be careful to prevent contact with
oil.
EI-18
REAR BUMPER
Revision; 2004 April
2003 Murano
PIIA3830E
1.
Bumper reinforcement
2.
Energy absorber
3.
Bumper fascia assembly
4.
Bumper side bracket
5.
Bumper stay
REAR BUMPER
EI-19
C
D
E
F
G
H
J
K
L
M
A
B
EI
Revision; 2004 April
2003 Murano
REMOVAL
1.
Remove rear combination lamp assembly. Refer to
LT-304, "Removal and Installation"
.
2.
Remove bumper fascia bolts from both right/left rear fender.
3.
Remove upper portion of bumper fascia clips, and remove clips of lower portion.
4.
Pull out center of bumper fascia, and pull out side of bumper fascia from clips.
5.
Remove bumper fascia assembly.
6.
Remove rear bumper energy absorber.
7.
Remove bumper reinforcement nuts and remove bumper reinforce assembly.
INSTALLATION
Install in the reverse order of removal.
REAR BUMPER CLOSING
Removal
1.
Remove clips of bumper closing.
2.
Remove bumper closing.
Installation
Install in the reverse order of removal.
DRAFTER GUARD
Removal
1.
Remove nut and bolt of drafter guard.
2.
Remove drafter guard assembly.
Installation
Install in the reverse order of removal.
PIIA3839E
PIIA3840E
EI-20
FRONT GRILLE
Revision; 2004 April
2003 Murano
FRONT GRILLE
PFP:62310
Removal and Installation
AIS002A5
REMOVAL
1.
Apply protection tape around outer circumference of front grille (bumper fascia side).
2.
Remove front grille-radiator cover clips and remove front grille-radiator cover.
3.
Remove clips on upper side of front grille.
4.
Pull out grille pawls, and remove front grille assembly.
INSTALLATION
Install in the reverse order of removal.
PIIA3831E
1.
Front grille
2.
Front grille-radiator cover (left)
3.
Front grille-radiator cover (right)
COWL TOP
EI-21
C
D
E
F
G
H
J
K
L
M
A
B
EI
Revision; 2004 April
2003 Murano
COWL TOP
PFP:66100
Removal and Installation
AIS002A6
REMOVAL
1.
Remove both right/left wiper arms.Refer to
WW-47, "Removal and Installation of Front Wiper Arms,
Adjustment of Wiper Arms Stop Location"
.
2.
Remove cowl top seal rubber.
3.
Remove clips of cowl top cover (right) and remove cowl top cover (right).
4.
Remove clips of cowl top cover (left) and remove cowl top cover (left).
5.
Remove washer nozzles and hose from cowl top cover.
INSTALLATION
Install in the reverse order of removal.
PIIA3832E
1.
Cowl top cover (right)
2.
Cap (left/right)
3.
Cowl top seal rubber
4.
Cowl top cover (left)
EI-22
FENDER PROTECTOR
Revision; 2004 April
2003 Murano
FENDER PROTECTOR
PFP:63840
Removal and Installation
AIS002A7
REMOVAL
1.
Remove screws of fender protector.
2.
Remove clips of fender protector.
3.
Remove fender protector (front) and fender protector (rear).
INSTALLATION
Install in the reverse order of removal.
PIIA3833E
1.
Fender protector (front)
2.
Fender protector (rear)
DOOR OUTSIDE MOLDING
EI-23
C
D
E
F
G
H
J
K
L
M
A
B
EI
Revision; 2004 April
2003 Murano
DOOR OUTSIDE MOLDING
PFP:82820
Removal and Installation
AIS002A8
FRONT DOOR OUTSIDE MOLDING
Removal
1.
Open windows fully.
2.
Disengage front door outside molding tab.
3.
Reaching from inner side of door use a clip tool to disengage front door outside molding from the tab.
NOTE:
Insert clip clamp tool into the door tab, then disengage by pressing in the direction of arrow (see figure on the
right).
Installation
Install in the reverse order of removal.
REAR DOOR OUTSIDE MOLDING
Removal
1.
Open windows fully.
2.
Disengage rear door outside molding tab.
3.
Reaching from inner side of door use a clip tool to disengage rear door outside molding from the tab.
NOTE:
Insert clip clamp tool into the door tab, then disengage by pressing in the direction of arrow (see figure on the
right).
Installation
Install in the reverse order of removal.
1.
Front door outside molding
2.
Rear door outside molding
PIIA3834E
EI-24
DOOR OUTSIDE LOWER MOLDING
Revision; 2004 April
2003 Murano
DOOR OUTSIDE LOWER MOLDING
PFP:82877
Removal and Installation
AIS002BQ
FRONT DOOR OUTSIDE LOWER MOLDING
Removal
Remove to slide molding to vehicle backward side, after disconnecting all clips.
Installation
Install in the reverse order of removal.
REAR DOOR OUTSIDE LOWER MOLDING
Removal
Remove to slide molding to vehicle backward side, after disconnecting all clips.
Installation
Install in the reverse order of removal.
FRONT FENDER LOWER MOLDING
Removal
1.
Remove screw of front fender lower molding.
2.
Remove front fender lower molding.
Installation
Install in the reverse order of removal.
PIIA3835E
1.
Front fender lower molding
2.
Front door outside lower molding
3.
Rear door outside lower molding
DOOR PARTING SEAL
EI-25
C
D
E
F
G
H
J
K
L
M
A
B
EI
Revision; 2004 April
2003 Murano
DOOR PARTING SEAL
PFP:80838
Removal and Installation
AIS002A9
REMOVAL
1.
Open front door and rear door fully.
2.
Remove seal clips and remove door parting seal.
3.
Remove rear door parting seal.
INSTALLATION
Install in the reverse order of removal.
PIIA3836E
1.
Door parting seal rubber
2.
Rear door parting seal rubber
EI-26
WINDSHIELD MOLDING
Revision; 2004 April
2003 Murano
WINDSHIELD MOLDING
PFP:72700
Removal and Installation
AIS002AA
WINDSHIELD MOLDING
Removal
Remove windshield molding. Refer to
GW-11, "Removal and Installation"
Installation
Install windshield molding. Refer to
GW-11, "Removal and Installation"
.
PIIA3784E
1.
Clip (C103)
2.
Fastener
3.
Molding
4.
Windshield glass
5.
Spacer
6.
Mirror base
7.
Bond
8.
Insulator
9.
Panel
10. Body side (outer)
11. Cowl top cover
SIDE WINDOW GLASS
EI-27
C
D
E
F
G
H
J
K
L
M
A
B
EI
Revision; 2004 April
2003 Murano
SIDE WINDOW GLASS
PFP:83300
Removal and Installation
AIS005DA
SIDE WINDOW MOLDING
Removal
Remove side window molding. Refer to
EI-27, "Removal and Installation"
.
Installation
Install side window molding. Refer to
EI-27, "Removal and Installation"
.
PIIA3793E
1.
Side window glass molding (Upper)
2.
Side window glass
3.
Clip
4.
Side window glass molding (Lower)
5.
Bond
6.
Body side outer panel
EI-28
ROOF SIDE MOLDING
Revision; 2004 April
2003 Murano
ROOF SIDE MOLDING
PFP:73854
Removal and Installation
AIS002AD
REMOVAL
1.
Disconnect molding clips from roof panel portion.
2.
Remove roof side molding from the front side.
INSTALLATION
Install in the reverse order of removal.
CAUTION:
To install roof side molding, check if all clips are matched over holes of panel on vehicle , then push it.
PIIA3848E
1.
Roof side molding
ROOF RAIL
EI-29
C
D
E
F
G
H
J
K
L
M
A
B
EI
Revision; 2004 April
2003 Murano
ROOF RAIL
PFP:73820
Removal and Installation
AIS002AE
REMOVAL
1.
Remove roof rail cover (front/rear).
2.
Remove roof rail center cap.
3.
Remove roof rail front/rear leg bolts and remove roof rail center screw.
4.
Remove roof rail assembly.
5.
Remove roof rail center leg.
6.
Remove roof side molding. Refer to
EI-28, "Removal and Installation"
INSTALLATION
Install in the reverse order of removal.
CAUTION:
Match the position to location pin and assembly center leg and rail assembly.
PIIA3841E
1.
Roof rail rear cover
2.
Roof rail center cap
3.
Roof rail front cover
4.
Roof rail front leg
5.
Roof side molding
6.
Roof rail center leg
7.
Roof rail assembly
8.
Roof rail rear leg
EI-30
DOOR FINISHER
Revision; 2004 April
2003 Murano
DOOR FINISHER
PFP:80900
Removal and Installation
AIS002AF
DOOR FINISHER (FRONT AND REAR)
Removal
1.
Remove cap of inside handle portion and remove screws.
2.
Remove inside handle escutcheon.
3.
Remove screw of grip portion.
4.
Remove pull handle cap and remove screw.
5.
Remove power window switch and disconnect harness connector of power window switch.
6.
Remove screws of power window switch side portion.
PIIA3842E
1.
Door finisher (front door)
2.
Cap (front door)
3.
Power window switch finisher (front
right / left)
4.
Inside handle escutcheon (front right
/ left)
5.
Door finisher (rear door)
6.
Cap (rear door)
7.
Power window switch finisher (rear
door)
8.
Inside handle escutcheon (rear)
DOOR FINISHER
EI-31
C
D
E
F
G
H
J
K
L
M
A
B
EI
Revision; 2004 April
2003 Murano
7.
Insert screw driver rolled with cloth between panel on vehicle
and clips (as indicated with arrow), and remove finisher.
8.
Pull up door finisher, and remove step lamp connector and electrical parts connectors.
9.
Remove lock knob cable and inside handle cable of inside han-
dle assembly back side.
10. Remove inside handle screws, and remove it from finisher.
Installation
Install in the reverse order of removal.
CAUTION:
●
To install finisher, check if all clips are matched over holes of panel on vehicle, then push it.
●
Be careful at the time of install with the wound to door trim finisher.
SIIA0810E
PIIA1216E
EI-32
BODY SIDE TRIM
Revision; 2004 April
2003 Murano
BODY SIDE TRIM
PFP:76913
Removal and Installation
AIS002AG
CAUTION:
Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes.
CENTER PILLAR LOWER GARNISH
Removal
1.
Remove front and rear kicking plate.
2.
Remove center pillar lower garnish.
Installation
Install in the reverse order of removal.
CENTER PILLAR UPPER GARNISH
Removal
1.
Remove front seat belt shoulder anchor. Refer to
SB-4, "Removal and Installation of Front Seat Belt"
2.
Remove front and rear kicking plate.
3.
Remove center pillar lower garnish.
4.
Remove center pillar upper garnish.
1.
Front pillar garnish
2.
Front body side welt
3.
Dash side finisher
4.
Front kicking plate
5.
Center pillar lower garnish
6.
Rear kicking plate
7.
Rear body side welt
8.
Center pillar upper cap
9.
Center pillar upper garnish
PIIA3843E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст