Nissan Murano Z50 (2003 year). Manual — part 287
WW-64
REAR WIPER AND WASHER SYSTEM
Revision; 2004 April
2003 Murano
5.
CHECK AUTO STOP SIGNAL
1.
Connect BCM connector.
2.
Turn ignition switch ON.
3.
Check voltage between rear wiper motor harness connector
D103 terminal 3 (O) and ground.
OK or NG
OK
>> Replace BCM. Refer to
BCS-36, "Removal and Installa-
NG
>> Replace rear wiper motor.
Only Rear Wiper Does Not Operate
AKS004XC
1.
CHECK COMBINATION SWITCH INPUT SIGNAL
Select “BCM” on CONSULT-II. With “WIPER” data monitor, make
sure “RR WIPER ON” turns ON-OFF according to operation of wiper
switch.
OK or NG
OK
>> Replace BCM. Refer to
BCS-36, "Removal and Installa-
NG
>> Replace wiper switch.
Only Rear Wiper Intermittent Does Not Operate
AKS004XD
1.
CHECK COMBINATION SWITCH INPUT SIGNAL
Select “BCM” on CONSULT-II. With “WIPER” data monitor, make
sure “RR WIPER INT” turns ON-OFF according to operation of wiper
switch.
OK or NG
OK
>> Replace BCM. Refer to
BCS-36, "Removal and Installa-
NG
>> Replace wiper switch.
Wiper Does Not Wipe When Rear Washer Operates
AKS004XE
1.
CHECK COMBINATION SWITCH INPUT SIGNAL
Select “BCM” on CONSULT-II. With “WIPER” data monitor, make
sure “RR WASHER SW” turns ON-OFF according to operation of
rear washer switch.
OK or NG
OK
>> Replace BCM. Refer to
BCS-36, "Removal and Installa-
NG
>> Replace wiper switch.
Battery voltage should exist.
SKIA4247E
When rear wiper switch is ON
position
: RR WIPER ON ON
SKIA4248E
When rear wiper switch is INT
position
: RR WIPER INT ON
SKIA4249E
When rear wiper switch is
WASHER position
: RR WASHER SW ON
SKIA4250E
REAR WIPER AND WASHER SYSTEM
WW-65
C
D
E
F
G
H
I
J
L
M
A
B
WW
Revision; 2004 April
2003 Murano
Removal and Installation of Rear Wiper Arm, Adjustment of Wiper Arms Stop
Location
AKS004XF
REMOVAL
1.
Operate wiper motor, and stop it at the auto stop position.
2.
Remove wiper arm cover and mounting nut, and then remove wiper arm from vehicle.
INSTALLATION
1.
Clean up the pivot area as illustrated. This will reduce possibility
of wiper arm looseness.
2.
Prior to wiper arm installation, turn on wiper switch to operate
wiper motor and then turn it “OFF” (Auto Stop).
3.
Lift the blade up and then set it down onto glass surface to set
the blade center to clearance “L” immediately before tightening
nut.
4.
Eject washer fluid. Turn on wiper switch to operate wiper motor
and then turn it “OFF”.
5.
Ensure that wiper blades stop within clearance “L”.
●
Tighten wiper arm nut to specified torque.
ADJUSTMENT
Refer to
SEL024J
Clearance “L”
: 20.5 - 35.5 mm (0.807 - 1.398 in)
Rear wiper arm
mounting nut
: 8.8 N·m
(0.9 kg-m, 78 in-lb)
PKIA2561E
WW-66
REAR WIPER AND WASHER SYSTEM
Revision; 2004 April
2003 Murano
Removal and Installation of Rear Wiper Motor
AKS004XG
REMOVAL
1.
Remove wiper arm. Refer to
WW-65, "Removal and Installation
of Rear Wiper Arm, Adjustment of Wiper Arms Stop Location"
2.
Remove pivot cap.
3.
Remove back door finisher. Refer to
in “EI” section.
4.
Disconnect rear wiper motor connector.
5.
Remove rear wiper motor mounting bolts and remove rear
wiper motor.
INSTALLATION
1.
Attach pivot cap.
2.
Install rear wiper motor to the vehicle.
3.
Connect rear wiper motor to the connector. Turn rear wiper switch ON to operate rear wiper motor, then
turn wiper switch OFF (auto stop).
4.
Install back door finisher. Refer to
5.
WW-65, "Removal and Installation of Rear Wiper Arm, Adjustment of Wiper
.
PKIA7853E
1.
Wiper blade
2.
Wiper arm
3.
Wiper arm cover
4.
Pivot cap
5.
Rear wiper motor
PKIA2563E
Rear wiper motor mounting bolts
: 4.5 N·m (0.46 kg-m, 40 in-lb)
REAR WIPER AND WASHER SYSTEM
WW-67
C
D
E
F
G
H
I
J
L
M
A
B
WW
Revision; 2004 April
2003 Murano
CAUTION:
●
Do not drop the wiper motor or cause it to contact other parts.
Removal and Installation of Rear Wiper Blade
AKS005QT
REMOVAL
Remove the wiper blade as following the procedure below. (As shown No.1 to 8 in the illustration.)
PKIA2693E
WW-68
REAR WIPER AND WASHER SYSTEM
Revision; 2004 April
2003 Murano
CAUTION:
●
If the detaching force in the arrowed direction (see the illus-
tration) is less than 68.6N·m (7.0kg-m, 51ft-lb), replace rear
wiper blade and rear wiper arm with new ones.
●
When replacing the rear wiper blade, blow air and remove
shaving of plastic or dust.
INSTALLATION
Install in the reverse order of removal.
Washer Nozzle Adjustment
AKS004XH
●
Adjust washer nozzle with suitable tool as shown in the figure.
Unit : mm (in)
PKIA2692E
Adjustable range
:
±
15
°
(in any direction)
PKIA2564E
h (height)
23.3 (0.91)
φ
(spray position range)
30 (1.18)
PKIA2565E
REAR WIPER AND WASHER SYSTEM
WW-69
C
D
E
F
G
H
I
J
L
M
A
B
WW
Revision; 2004 April
2003 Murano
Washer Tube Layout
AKS004XI
Removal and Installation of Rear Washer Nozzle
AKS005HH
1.
Remove high-mounted stop lamp. Refer to
in “LT” section.
2.
Remove rear washer nozzle mounting screw and remove it.
3.
Note the following, and install in the reverse order of removal.
●
Tighten rear washer nozzle mounting screw to specified
torque.
CAUTION:
●
After tightened rear washer nozzle mounting screw, make
sure that the rear washer nozzle does not come off when
it is pulled downward at 49N·m (5kg-m, 36ft-lb) as shown
in the figure.
If the washer nozzle come off, replace it together with a
new high-mounted stop lamp assembly.
PKIA2566E
Rear washer nozzle mounting screw
:0.4 N·m (0.04 kg-m, 4 in-lb)
PKIA2548E
PKIA2955E
WW-70
REAR WIPER AND WASHER SYSTEM
Revision; 2004 April
2003 Murano
Check Valve
AKS004XJ
●
A check valve is provided in the washer fluid line. Be careful not
to connect check valve to washer tube in the wrong direction.
Removal and Installation of Rear Wiper and Washer Switch
AKS004XK
Refer to
WW-51, "Removal and Installation of Front Wiper and Washer Switch"
.
Removal and Installation of Washer Tank
AKS004XL
Refer to
WW-51, "Removal and Installation of Washer Tank"
.
Removal and Installation of Washer Pump
AKS004XM
Refer to
WW-52, "Removal and Installation of Washer Pump"
PKIA2546E
POWER SOCKET
WW-71
C
D
E
F
G
H
I
J
L
M
A
B
WW
Revision; 2004 April
2003 Murano
POWER SOCKET
PFP:253A2
Wiring Diagram — P/SCKT —
AKS004NM
TKWA0787E
WW-72
POWER SOCKET
Revision; 2004 April
2003 Murano
Removal and Installation of Instrument Power Socket
AKS004NN
REMOVAL
1.
Remove inner socket with power socket lid assembly from
instrument panel, while pressing the pawls.
2.
Disconnect power socket connector.
3.
Remove inner socket from power socket lid assembly, while
pressing the hook out from square hole.
INSTALLATION
Instal in the reverse order of removal.
Removal and Installation of Luggage Room Power Socket
AKS005I6
REMOVAL
1.
Remove inner socket from the ring, while pressing the hook on
the ring out from square hole.
2.
Remove luggage side finisher lower (right). Refer to
in “EI” section.
3.
Turn holder nut counterclockwise and unlock it.
4.
Remove the ring from inner trim.
INSTALLATION
Install in the reverse order of removal.
Removal and Installation of Console Power Socket
AKS005I5
1.
in “IP” section.
2.
Remove inner socket from the ring, while pressing the hook on
the ring out from square hole.
3.
Remove power socket finisher assembly mounting screws and
remove it.
4.
Remove the ring from power socket finisher while pressing
pawls.
PKIA2568E
PKIA2569E
PKIA2571E
HORN
WW-73
C
D
E
F
G
H
I
J
L
M
A
B
WW
Revision; 2004 April
2003 Murano
HORN
PFP:25610
Wiring Diagram — HORN —
AKS004NO
TKWA0788E
WW-74
HORN
Revision; 2004 April
2003 Murano
Removal and Installation
AKS004NP
REMOVAL
1.
Remove front bumper. Refer to
in
“EI” section.
2.
Disconnect horn connector.
3.
Remove horn bolt and remove horn from vehicle.
INSTALLATION
Tighten horn bolt to specified torque.
PKIA2570E
PKIA2559E
Horn mounting bolt
: 17.1 N·m (1.7 kg-m, 13 ft-lb)
CIGARETTE LIGHTER
WW-75
C
D
E
F
G
H
I
J
L
M
A
B
WW
Revision; 2004 April
2003 Murano
CIGARETTE LIGHTER
PFP:35330
Wiring Diagram — CIGAR —
AKS007O2
TKWA1057E
WW-76
CIGARETTE LIGHTER
Revision; 2004 April
2003 Murano
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст