Nissan Pathfinder (2007 year). Manual — part 407
SIDE OIL SEAL
TF-137
[ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
TF
2007 Pathfinder
SIDE OIL SEAL
PFP:33142
Removal and Installation
EDS0037E
REMOVAL
1.
Remove the front propeller shaft. Refer to
.
2.
Remove the companion flange. Refer to
3.
Remove the transfer control device from the transfer assembly. Refer to
TF-138, "Removal and Installa-
4.
Remove the side oil seal using suitable tool.
CAUTION:
Do not damage shift cross.
INSTALLATION
1.
Install the new side oil seal until it is flush with the end face of
case using Tool.
CAUTION:
●
Do not reuse oil seal.
●
Apply petroleum jelly to oil seal.
2.
Install the transfer control device to the transfer assembly. Refer
to
TF-138, "Removal and Installation"
.
3.
Install the companion flange. Refer to
.
4.
Install the front propeller shaft. Refer to
SDIA2666E
Tool number
: ST22360002 (J-25679-01)
SDIA2665E
TF-138
[ATX14B]
TRANSFER CONTROL DEVICE
2007 Pathfinder
TRANSFER CONTROL DEVICE
PFP:33251
Removal and Installation
EDS0037F
CAUTION:
●
Change vehicle state to 2WD, and then remove and install transfer control device.
●
Check 4WD shift indicator after installation. Refer to
TF-6, "Precautions for Transfer Assembly and
Transfer Control Unit Replacement"
1.
Shift lever
2.
Actuator
SDIA2654E
AIR BREATHER HOSE
TF-139
[ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
TF
2007 Pathfinder
AIR BREATHER HOSE
PFP:31098
Removal and Installation
EDS003LE
CAUTION:
●
Make sure there are no pinched or restricted areas on each air breather hose caused by folding or
bending when installing it.
●
Install each air breather hose into the breather tube (metal
connector) until the hose end reaches the end of the curve
section. Set each air breather hose with paint mark facing
upward.
●
Install actuator/transfer motor air breather hose and trans-
fer air breather hose on clip A and clip B with the paint mark
facing upward.
1.
Breather tube
2.
Clip A
3.
Clip B
4.
Clip C
5.
Clip D
6.
Clip E
7.
Actuator
8.
Air breather hose clamp
9.
Clip F
10. Transfer motor
11.
Breather tube (transfer)
SDIA3339E
SDIA3340E
SDIA3342E
TF-140
[ATX14B]
AIR BREATHER HOSE
2007 Pathfinder
●
Install clip C on actuator/transfer motor air breather hose
and transfer air breather hose with the paint mark matched.
●
Install actuator/transfer motor air breather hose and trans-
fer air breather hose on clip D and clip E with the paint mark
facing upward.
●
Install the actuator air breather hose into the actuator (case
connector) until the hose end reaches the base of the tube.
Set actuator air breather hose with paint mark facing left-
ward.
●
Install clip F on transfer motor air breather hose and trans-
fer air breather hose with the paint mark matched.
●
Install the transfer air breather hose into the breather tube
(transfer, metal connector) until the hose end reaches the
base of the tube. Set transfer air breather hose with paint
mark facing upwards.
SDIA3343E
SDIA3344E
SDIA3226E
SDIA3345E
SDIA3196E
AIR BREATHER HOSE
TF-141
[ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
TF
2007 Pathfinder
●
Install the transfer motor air breather hose into the transfer
motor (case connector) until the hose end reaches the end
of the curved section. Set transfer motor air breather hose
with paint mark facing leftward.
SDIA3194E
TF-142
[ATX14B]
TRANSFER MOTOR
2007 Pathfinder
TRANSFER MOTOR
PFP:00000
Removal and Installation
EDS0037H
REMOVAL
1.
Disconnect the transfer motor connector.
2.
Remove the transfer motor air breather hose from the transfer
motor. Refer to
TF-139, "Removal and Installation"
3.
Remove the transfer motor bolts.
4.
Remove the transfer motor.
INSTALLATION
1.
Apply ATF to the new O-ring and install it to the transfer motor.
CAUTION:
Do not reuse O-rings.
2.
Fit the double-flat end of the transfer motor shaft into the slot of
the sub-oil pump assembly. Then tighten to the specified torque.
Refer to
.
CAUTION:
Be sure to install connector bracket.
3.
Install the transfer motor air breather hose to the transfer motor.
Refer to
TF-139, "Removal and Installation"
4.
Connect the transfer motor connector.
5.
Check the transfer fluid. Refer to
TF-13, "FLUID LEAKAGE AND FLUID LEVEL"
.
6.
Start the engine for one minute. Then stop the engine and recheck the transfer fluid. Refer to
"FLUID LEAKAGE AND FLUID LEVEL"
SDIA2133E
SDIA2787E
TRANSFER OIL FILTER
TF-143
[ATX14B]
C
E
F
G
H
I
J
K
L
M
A
B
TF
2007 Pathfinder
TRANSFER OIL FILTER
PFP:00000
Removal and Installation
EDS0037I
REMOVAL
1.
Remove the oil filter bolts and oil filter.
CAUTION:
●
Do not damage center case or oil filter.
●
Loosen bolts and detach oil filter evenly.
2.
Remove the O-rings (1) from the oil filter (2).
3.
Remove the oil filter stud from the oil filter.
4.
Remove the O-ring from the oil filter stud.
INSTALLATION
1.
Apply ATF to the new O-ring, and install it on the oil filter stud.
CAUTION:
Do not reuse O-ring.
2.
Install the oil filter stud to the oil filter.
SMT875C
WDIA0285E
SDIA3180E
SDIA3180E
TF-144
[ATX14B]
TRANSFER OIL FILTER
2007 Pathfinder
3.
Apply ATF to the two new O-rings (1), and install them on the oil
filter (2).
CAUTION:
Do not reuse O-rings.
4.
Install the oil filter to the transfer assembly. Tighten the bolts to
the specified torque. Refer to
.
CAUTION:
●
Do not damage oil filter.
●
Attach oil filter and tighten bolts evenly.
5.
Check the transfer fluid. Refer to
.
6.
Start the engine for one minute. Then stop the engine and
recheck the transfer fluid. Refer to
WDIA0285E
SDIA2136E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст