Nissan Pathfinder (2007 year). Manual — part 139
WARNING LAMPS
DI-35
C
D
E
F
G
H
I
J
L
M
A
B
DI
2007 Pathfinder
WKWA5303E
DI-36
WARNING LAMPS
2007 Pathfinder
Part Time 4WD Models
WKWA5304E
WARNING LAMPS
DI-37
C
D
E
F
G
H
I
J
L
M
A
B
DI
2007 Pathfinder
All Mode 4WD Models
WKWA5305E
DI-38
WARNING LAMPS
2007 Pathfinder
Oil Pressure Warning Lamp Stays Off (Ignition Switch ON)
EKS00FYO
1.
CHECK SELF-DIAGNOSTIC RESULTS OF IPDM E/R
Select "IPDM E/R" on CONSULT-II, and perform self-diagnosis of IPDM E/R. Refer to
Self-diagnostic results content
No malfunction detected>>GO TO 2.
Malfunction detected>>GO TO
2.
CHECK IPDM E/R INPUT SIGNAL
Select "IPDM E/R" on CONSULT-II. Operate ignition switch with "OIL
P SW" of "DATA MONITOR" and check operation status.
OK or NG
OK
>> Replace combination meter. Refer to
NG
>> GO TO 3.
3.
CHECK OIL PRESSURE SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector E122 and oil pressure switch
connector E208.
3.
Check continuity between IPDM E/R harness connector E122
(A) terminal 42 and oil pressure switch harness connector E208
(B) terminal 1.
OK or NG
OK
>> GO TO 4.
NG
>> Repair harness or connector.
4.
CHECK OIL PRESSURE SWITCH
Check oil pressure switch. Refer to
DI-23, "OIL PRESSURE SWITCH CHECK"
OK or NG
OK
>> Replace IPDM E/R. Refer to
PG-32, "Removal and Installation of IPDM E/R"
NG
>> Replace oil pressure switch.
Oil Pressure Warning Lamp Does Not Turn Off (Oil Pressure Is Normal)
EKS00FYP
NOTE:
For oil pressure inspection, refer to
1.
CHECK ENGINE OIL PRESSURE GAUGE OPERATION
Observe operation of engine oil pressure gauge.
Does engine oil pressure gauge function properly?
YES
>> Replace the combination meter. Refer to
.
NO
>> GO TO
DI-19, "Engine Oil Pressure Signal Inspection"
When ignition switch is in ON
position (Engine stopped)
: OIL P SW CLOSE
When engine running
: OIL P SW OPEN
LKIA0403E
Continuity should exist.
WKIA5607E
A/T INDICATOR
DI-39
C
D
E
F
G
H
I
J
L
M
A
B
DI
2007 Pathfinder
A/T INDICATOR
PFP:24814
Wiring Diagram — AT/IND —
EKS00FYQ
WKWA2060E
DI-40
A/T INDICATOR
2007 Pathfinder
A/T Indicator Does Not Illuminate
EKS00FYR
1.
CHECK SELF-DIAGNOSIS OF COMBINATION METER
Perform combination meter self-diagnosis. Refer to
DI-11, "SELF-DIAGNOSIS FUNCTION"
.
OK or NG
OK
>> GO TO 2.
NG
>> Replace combination meter. Refer to
.
2.
CHECK TCM
Perform self-diagnosis of TCM. Refer to
AT-88, "SELF-DIAGNOSTIC RESULT MODE"
.
OK or NG
OK
>> Replace combination meter. Refer to
.
NG
>> Refer to
WARNING CHIME
DI-41
C
D
E
F
G
H
I
J
L
M
A
B
DI
2007 Pathfinder
WARNING CHIME
PFP:24814
Component Parts and Harness Connector Location
EKS00FYS
System Description
EKS00FYT
FUNCTION
Power is supplied at all times
●
through 50A fusible link (letter g , located in the fuse and fusible link box)
●
to BCM terminal 70,
●
through 10A fuse (No. 25, located in the fuse and fusible link box)
●
to key switch terminal 2,
●
through 10A fuse [No. 19, located in the fuse block (J/B)]
●
to combination meter terminal 3.
With ignition switch in ON or START position, power is supplied
●
through 10A fuse [No. 1, located in the fuse block (J/B)]
●
to BCM terminal 38,
●
through 10A fuse [No. 14, located in the fuse block (J/B)]
●
to combination meter terminal 16.
Ground is supplied
●
to BCM terminal 67 and
●
to combination meter terminals 13 and 23
●
through body grounds M57, M61, and M79.
1.
Combination switch (lighting switch)
M28
2.
Combination meter M24
3.
Key switch M27
4.
BCM M18, M19, M20 (view with
instrument lower panel LH removed)
5.
Front door switch LH B8
6.
Seat belt buckle switch LH B12
WKIA4890E
DI-42
WARNING CHIME
2007 Pathfinder
NOTE:
When ignition key warning chime, light warning chime, and seat belt warning chime are required at the same
time, the priorities for each chime are the following.
1.
Light warning chime
2.
Ignition key warning chime
3.
Seat belt warning chime
LIGHT WARNING CHIME
With the key removed from the ignition switch, the driver's door open, and the lighting switch (part of the com-
bination switch) in 1st or 2nd position, the warning chime will sound. [Except when headlamp battery saver
control operates (5 minutes after ignition switch is turned to OFF or ACC position) and headlamps do not illu-
minate.]
Signal is supplied
●
from combination switch (lighting switch) terminals 1, 2, 3, 4, 5, 6, 7, 8, 9 and 10
●
to BCM terminals 2, 3, 4, 5, 6, 32, 33, 34, 35 and 36.
NOTE:
Lighting switch (detected by BCM) is in 1st or 2nd position. Refer to
.
Ground is supplied
●
to BCM terminal 47
●
through front door switch LH terminal 2.
Front door switch LH is case grounded.
BCM detects headlamps are illuminated, and sends light warning signal to combination meter via CAN com-
munication lines. When the combination meter receives light warning signal, it sounds warning chime.
IGNITION KEY WARNING CHIME
With the key inserted in the ignition switch, the ignition switch in OFF position, and the driver's door open, the
warning chime will sound.
Power is supplied
●
through key switch terminal 1
●
to BCM terminal 37.
Ground is supplied
●
to BCM terminal 47
●
through front door switch LH terminal 2.
Front door switch LH is case grounded.
BCM detects key inserted into the ignition switch, and sends key warning signal to combination meter via CAN
communication lines. When the combination meter receives key warning signal, it sounds warning chime.
SEAT BELT WARNING CHIME
When the ignition switch is turned ON with the driver seat belt unfastened (seat belt buckle switch LH unfas-
tened), warning chime will sound for approximately 6 seconds.
Ground is supplied
●
to combination meter terminal 24
●
through seat belt buckle switch LH terminal 1.
Seat belt buckle switch LH terminal 2 is grounded through body grounds B7 and B19.
The combination meter sends seat belt buckle switch LH unfastened signal to BCM via CAN communication
line.
BCM receives seat belt buckle switch LH unfastened signal from combination meter via CAN communication
line, and sends seat belt warning signal to the combination meter via CAN communication line. When the
combination meter receives the seat belt warning signal, it sounds the warning chime. The BCM controls the
(6 second) duration of the seat belt warning chime.
CAN Communication System Description
EKS00FYU
Refer to
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст