Nissan Pathfinder (2007 year). Manual — part 282
SQUEAK AND RATTLE TROUBLE DIAGNOSES
IP-7
C
D
E
F
G
H
J
K
L
M
A
B
IP
2007 Pathfinder
TRUNK
Trunk noises are often caused by a loose jack or loose items put into the trunk by the owner.
In addition look for:
1.
Trunk lid bumpers out of adjustment
2.
Trunk lid striker out of adjustment
3.
The trunk lid torsion bars knocking together
4.
A loose license plate or bracket
Most of these incidents can be repaired by adjusting, securing or insulating the item(s) or component(s) caus-
ing the noise.
SUNROOF/HEADLINING
Noises in the sunroof/headlining area can often be traced to one of the following:
1.
Sunroof lid, rail, linkage or seals making a rattle or light knocking noise
2.
Sun visor shaft shaking in the holder
3.
Front or rear windshield touching headliner and squeaking
Again, pressing on the components to stop the noise while duplicating the conditions can isolate most of these
incidents. Repairs usually consist of insulating with felt cloth tape.
OVERHEAD CONSOLE (FRONT AND REAR)
Overhead console noises are often caused by the console panel clips not being engaged correctly. Most of
these incidents are repaired by pushing up on the console at the clip locations until the clips engage.
In addition look for:
1.
Loose harness or harness connectors.
2.
Front console map/reading lamp lens loose.
3.
Loose screws at console attachment points.
SEATS
When isolating seat noise it's important to note the position the seat is in and the load placed on the seat when
the noise is present. These conditions should be duplicated when verifying and isolating the cause of the
noise.
Cause of seat noise include:
1.
Headrest rods and holder
2.
A squeak between the seat pad cushion and frame
3.
The rear seatback lock and bracket
These noises can be isolated by moving or pressing on the suspected components while duplicating the con-
ditions under which the noise occurs. Most of these incidents can be repaired by repositioning the component
or applying urethane tape to the contact area.
UNDERHOOD
Some interior noise may be caused by components under the hood or on the engine wall. The noise is then
transmitted into the passenger compartment.
Causes of transmitted underhood noise include:
1.
Any component mounted to the engine wall
2.
Components that pass through the engine wall
3.
Engine wall mounts and connectors
4.
Loose radiator mounting pins
5.
Hood bumpers out of adjustment
6.
Hood striker out of adjustment
These noises can be difficult to isolate since they cannot be reached from the interior of the vehicle. The best
method is to secure, move or insulate one component at a time and test drive the vehicle. Also, engine RPM
or load can be changed to isolate the noise. Repairs can usually be made by moving, adjusting, securing, or
insulating the component causing the noise.
IP-8
SQUEAK AND RATTLE TROUBLE DIAGNOSES
2007 Pathfinder
Diagnostic Worksheet
EIS007UG
LAIA0072E
SQUEAK AND RATTLE TROUBLE DIAGNOSES
IP-9
C
D
E
F
G
H
J
K
L
M
A
B
IP
2007 Pathfinder
LAIA0071E
IP-10
INSTRUMENT PANEL ASSEMBLY
2007 Pathfinder
INSTRUMENT PANEL ASSEMBLY
PFP:68200
Removal and Installation
EIS007UH
INSTRUMENT PANEL
1.
Display unit bracket RH/LH
2.
Steering member assembly
3.
Passenger air bag module
4.
Speaker grille RH/LH
5.
Instrument panel and pad assembly 6.
Instrument side finisher
7.
Side ventilator grille RH/LH
8.
Upper glove box
9.
Upper glove box door
10.
Lower glove box damper assembly
11.
Lower instrument panel RH
12.
Fuse block cover
LIIA1740E
INSTRUMENT PANEL ASSEMBLY
IP-11
C
D
E
F
G
H
J
K
L
M
A
B
IP
2007 Pathfinder
Removal
CAUTION:
Before servicing, turn the ignition switch off, disconnect both battery cables and wait at lease 3 min-
utes.
1.
Disconnect battery negative terminal.
2.
Disconnect battery positive terminal.
3.
Remove the center console. Refer to
.
4.
Remove the combination meter. Refer to
5.
Remove front pillar upper finisher. Refer to
6.
Remove optical sensor. Refer to
LT-50, "Removal and Installation"
7.
Remove audio unit. Refer to
AV-61, "Removal and Installation"
8.
Remove display control unit, if equipped. Refer to
AV-153, "DISPLAY CONTROL UNIT"
.
9.
Remove cluster lid D. Refer to
10. Disconnect GPS antenna.
11. Remove the passenger air bag module. Refer to
SRS-42, "FRONT PASSENGER AIR BAG MODULE"
12. Remove the instrument stay RH/LH bolts.
13. Remove instrument panel.
●
Disconnect all remaining harnesses.
Installation
Installation is in the reverse order of removal.
CLUSTER LID C -WITHOUT NAVIGATION SYSTEM
Removal
CAUTION:
Before servicing, turn the ignition switch off, disconnect both battery cables and wait at lease 3 min-
utes.
13.
Lower glove box
14.
Lower glove box latch assembly
15.
Cluster lid D
16.
Audio unit
17.
AV switch
18.
Display control unit
19.
Display unit
20.
Storage tray
21.
Cluster lid C
22.
Center ventilator grill RH/LH
23.
Column cover lower
24.
Column cover upper
25.
Steering lock escutcheon
26.
Combination meter
27.
Cluster lid A
28.
Lower instrument panel LH
29.
Knee protector brace
30.
Instrument stay RH/LH
31.
Knee protector
WIIA1050E
1.
Liner
2.
Storage tray
3.
Cluster lid C
4.
Cluster lid C screw
IP-12
INSTRUMENT PANEL ASSEMBLY
2007 Pathfinder
1.
Disconnect battery negative terminal.
2.
Disconnect battery positive terminal.
3.
.
4.
Remove storage tray and storage tray liner, then remove cluster lid C screw.
5.
Pull cluster lid C rearward to release clips.
6.
Disconnect electrical connectors and remove cluster lid C.
Installation
Installation is in the reverse order of removal.
CLUSTER LID C - WITH NAVIGATION SYSTEM
Removal
CAUTION:
Before servicing, turn the ignition switch off, disconnect both battery cables and wait at lease 3 min-
utes.
1.
Disconnect battery negative terminal.
2.
Disconnect battery positive terminal.
3.
.
4.
Pull cluster lid C rearward to release clips.
5.
Disconnect electrical connectors and remove cluster lid C.
Installation
Installation is in the reverse order of removal.
WIIA1051E
1.
Instrument panel
2.
Cluster lid C
INSTRUMENT PANEL ASSEMBLY
IP-13
C
D
E
F
G
H
J
K
L
M
A
B
IP
2007 Pathfinder
CLUSTER LID D
Removal
1.
Remove A/T finisher. Refer to
2.
Remove lower instrument panel LH. Refer to
IP-14, "LOWER INSTRUMENT PANEL LH"
3.
Remove lower instrument panel RH. Refer to
IP-15, "LOWER INSTRUMENT PANEL RH AND LOWER
.
4.
Remove cluster lid C. Refer to
IP-11, "CLUSTER LID C -WITHOUT NAVIGATION SYSTEM"
5.
Disconnect the electrical connectors and remove cluster lid D.
Installation
Installation is in the reverse order of removal.
WIIA1052E
1.
Cluster lid D
2.
Cluster lid D screws
IP-14
INSTRUMENT PANEL ASSEMBLY
2007 Pathfinder
LOWER INSTRUMENT PANEL LH
Removal
1.
Remove front pillar lower finisher. Refer to
EI-29, "FRONT PILLAR LOWER FINISHER"
.
2.
Remove lower instrument panel LH, using power tool.
3.
Pull rearward to release lower instrument panel LH.
4.
Disconnect lower instrument panel LH harness connectors.
Installation
Installation is in the reverse order of removal.
COMBINATION METER
Removal
1.
Disconnect the negative battery cable.
2.
Remove front pillar upper finisher. Refer to
EI-29, "FRONT PILLAR UPPER FINISHER"
3.
Remove lower instrument panel LH. Refer to
IP-14, "LOWER INSTRUMENT PANEL LH"
.
4.
Remove steering lock escutcheon.
5.
Remove cluster lid A, using power tool.
6.
Remove combination meter, using power tool.
7.
Disconnect combination meter electrical connectors.
Installation
Installation is in the reverse order of removal.
LIIA1744E
WIIA1053E
1.
Combination meter
2.
Combination meter screws
3.
Cluster lid A
4.
Ignition key lamp assembly
5.
Steering lock escutcheon
6.
Cluster lid A screws
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст