Nissan Pathfinder (2007 year). Manual — part 356
SUNROOF
RF-25
C
D
E
F
G
H
J
K
L
M
A
B
RF
2007 Pathfinder
2.
Install the glass lid assembly screws. (First tighten left front bolt,
then tighten right rear bolt on glass lid to prevent lid from moving
while tightening other bolts.)
3.
Adjust the sunroof glass. Refer to
WIND DEFLECTOR
Removal
1.
Open the sunroof.
2.
Remove screws from the left, center, and right side wind deflec-
tor holders.
3.
Remove the wind deflector from the sunroof frame assembly.
Installation
Installation is in the reverse order of removal.
SUNSHADE
Removal
1.
Remove the sunroof frame assembly. Refer to
2.
Remove the sunshade stoppers (2 points) from the rear end of
the sunroof frame assembly.
3.
Remove the sunshade assembly from the rear end of the sun-
roof frame assembly.
Installation
Installation is in the reverse order of removal.
SUNROOF MOTOR
Removal
CAUTION:
●
When removing the sunroof motor, be sure that the sunroof is in the fully closed position.
●
Never run the removed motor as a single unit.
1.
Position the sunroof assembly in the fully closed position.
2.
Remove the front roof console assembly. Refer to
EI-31, "Removal and Installation"
WIIA0252E
WIIA0424E
LIIA1672E
RF-26
SUNROOF
2007 Pathfinder
3.
Disconnect the harness connector from the sunroof motor
assembly.
4.
Remove the mounting screws and the sunroof motor assembly.
Installation
CAUTION:
Before installing the sunroof motor assembly, be sure to place the link and wire assembly in the sym-
metrical and fully closed position.
1.
Move the sunroof motor assembly laterally little by little so that
the gear is completely engaged into the wire on the sunroof unit
and the mounting surface becomes parallel. Then secure the
motor with bolts.
2.
Connect the harness connector to the sunroof motor assembly.
3.
Install the front roof console assembly. Refer to
EI-31, "Removal and Installation"
.
4.
Reset the sunroof motor memory. Refer to
RF-12, "RE-TEACHING PROCEDURE"
.
DRAIN HOSES
Removal
LIIA1673E
LIIA1674E
1.
Drain hoses
WIIA1072E
SUNROOF
RF-27
C
D
E
F
G
H
J
K
L
M
A
B
RF
2007 Pathfinder
1.
Remove the headlining. Refer to
EI-31, "Removal and Installation"
2.
Visually check the drain hoses for proper connections, damage or deterioration.
3.
Remove each drain hose and check visually for damage, cracks or deterioration.
4.
Pour water through the drain hose to check for damage.
●
If any damage is found, replace the drain hose.
Installation
Installation is in the reverse order of removal.
WEATHERSTRIP
Visually check weatherstrip for any damage, deterioration, or flattening.
●
In the case of leakage around glass lid, close glass lid and pour water around it to find the damaged or
gaped portion, remove glass lid assembly. Refer to:
●
If any damage is found, replace glass lid assembly. Refer to:
CAUTION:
Do not remove weatherstrip.
LINK AND WIRE ASSEMBLY
NOTE:
Before replacing any suspect part, be sure it is the source of the noise.
1.
Visually check to determine if a sufficient amount of petroleum jelly has been applied to the wire or rail
groove. If not, add petroleum jelly as required.
2.
Check wire for any damage or deterioration. If any damage is found, remove rear guide, then replace
wire.
LIIA0272E
RF-28
SUNROOF
2007 Pathfinder
RFD-1
REAR FINAL DRIVE
D DRIVELINE/AXLE
CONTENTS
C
E
F
G
H
I
J
K
L
M
SECTION
RFD
A
B
RFD
2007 Pathfinder
PRECAUTIONS . . . . . . . . . . . . . . .. 2
Precautions for Servicing Rear Final Drive . . . .. 2
PREPARATION . . . . . . . . . . . . . . ... 3
Special Service Tools . . . . . . . . . . . ... 3
Commercial Service Tools . . . . . . . . . . 6
NOISE, VIBRATION AND HARSHNESS (NVH)
TROUBLESHOOTING . . . . . . . . . . . . 7
NVH Troubleshooting Chart . . . . . . . . . . 7
DESCRIPTION . . . . . . . . . . . . . . . 8
Cross-Sectional View . . . . . . . . . . . ... 8
DIFFERENTIAL GEAR OIL . . . . . . . . . . 9
Changing Differential Gear Oil . . . . . . . . . 9
DRAINING . . . . . . . . . . . . . . . . 9
FILLING . . . . . . . . . . . . . . . . . 9
Checking Differential Gear Oil . . . . . . . . .. 9
OIL LEAKAGE AND OIL LEVEL . . . . . . ... 9
FRONT OIL SEAL . . . . . . . . . . . . . 10
Removal and Installation . . . . . . . . . . 10
REMOVAL . . . . . . . . . . . . . . ... 10
INSTALLATION . . . . . . . . . . . . . 11
SIDE OIL SEAL . . . . . . . . . . . . . . 12
Removal and Installation . . . . . . . . . . 12
REMOVAL . . . . . . . . . . . . . . ... 12
INSTALLATION . . . . . . . . . . . . ... 12
CARRIER COVER . . . . . . . . . . . . . 14
Removal and Installation . . . . . . . . . . 14
REMOVAL . . . . . . . . . . . . . . ... 14
INSTALLATION . . . . . . . . . . . . ... 14
REAR FINAL DRIVE ASSEMBLY . . . . . . . 15
Removal and Installation . . . . . . . . . . 15
Disassembly and Assembly . . . . . . . . . 18
COMPONENTS . . . . . . . . . . . . ... 18
ASSEMBLY INSPECTION AND ADJUSTMENT
SERVICE DATA AND SPECIFICATIONS (SDS) . .. 38
General Specifications . . . . . . . . . . . 38
Inspection and Adjustment . . . . . . . . . . 38
RFD-2
PRECAUTIONS
2007 Pathfinder
PRECAUTIONS
PFP:00001
Precautions for Servicing Rear Final Drive
EDS0039U
●
Before starting diagnosis of the vehicle, understand the symptoms well. Perform correct and systematic
operations.
●
Check for the correct installation status prior to removal or disassembly. When matching marks are
required, be certain they do not interfere with the function of the parts they are applied to.
●
Overhaul should be done in a clean work area, a dust proof area is recommended.
●
Before disassembly, completely remove sand and mud from the exterior of the unit, preventing them from
entering into the unit during disassembly or assembly.
●
Always use shop paper for cleaning the inside of components.
●
Avoid using cotton gloves or a shop cloth to prevent the entering of lint.
●
Check appearance of the disassembled parts for damage, deformation, and abnormal wear. Replace
them with new ones if necessary.
●
Gaskets, seals and O-rings should be replaced any time the unit is disassembled.
●
Clean and flush the parts sufficiently and blow them dry.
●
Be careful not to damage sliding surfaces and mating surfaces.
●
When applying sealant, remove the old sealant from the mating surface; then remove any moisture, oil,
and foreign materials from the application and mating surfaces.
●
In principle, tighten nuts or bolts gradually in several steps working diagonally from inside to outside. If a
tightening sequence is specified, observe it.
●
During assembly, observe the specified tightening torque.
●
Add new differential gear oil, petroleum jelly, or multi-purpose grease, as specified.
PREPARATION
RFD-3
C
E
F
G
H
I
J
K
L
M
A
B
RFD
2007 Pathfinder
PREPARATION
PFP:00002
Special Service Tools
EDS0039V
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name
Description
KV40104000
(
—
)
Flange wrench
Removing and installing drive pinion lock nut
a: 85 mm (3.35 in) dia.
b: 65 mm (2.56 in) dia.
KV381054S0
(J-34286)
Puller
Removing front oil seal
ST30720000
(J-25405)
Drift
●
Installing front oil seal
●
Installing drive pinion rear bearing outer
race
a: 77 mm (3.03 in) dia.
b: 55.5 mm (2.185 in) dia.
ST36230000
(J-25840-A)
Sliding hammer
Removing side flange
KV40104100
(
—
)
Attachment
Removing side flange
KV38100200
(J-26233)
Drift
Installing side oil seal
a: 65 mm (2.56 in) dia.
b: 49 mm (1.93 in) dia.
KV38107900
(J-39352)
Protector
Installing side flange
NT659
ZZA0601D
ZZA0811D
ZZA0803D
ZZA0804D
ZZA1143D
S-NT129
RFD-4
PREPARATION
2007 Pathfinder
KV38100800
(J-25604-01)
Attachment
Securing unit assembly
a: 541 mm (21.30 in)
b: 200 mm (7.87 in)
ST3127S000
(J-25765-A)
Preload gauge
1: GG91030000
(J-25765)
Torque wrench
2: HT62940000
(
—
)
Socket adapter (1/2
″
)
3: HT62900000
(
—
)
Socket adapter (3/8
″
)
Measuring drive pinion bearing preload torque
and total preload torque
KV10111100
(J-37228)
Seal cutter
Removing carrier cover
ST3306S001
(
—
)
Differential side bearing puller set
1: ST33051001
(J-22888-20)
Puller
2: ST33061000
(J-8107-2)
Base
Removing and installing side bearing inner
race
a: 28.5 mm (1.122 in) dia.
b: 38 mm (1.50 in) dia.
ST30031000
(J-22912-01)
Puller
Removing drive pinion rear bearing inner race
KV40105230
(
—
)
Drift
Installing drive pinion rear bearing outer race
a: 92 mm (3.62 in) dia.
b: 86 mm (3.39 in) dia.
c: 45 mm (1.77 in) dia.
ST30611000
(J-25742-1)
Drift bar
Installing drive pinion front bearing outer race
(Use with ST30613000)
Tool number
(Kent-Moore No.)
Tool name
Description
SDIA0267E
NT124
S-NT046
NT072
ZZA0700D
PDIA0591E
S-NT090
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст