Nissan Pathfinder (2007 year). Manual — part 388
SPIRAL CABLE
SRS-41
C
D
E
F
G
I
J
K
L
M
A
B
SRS
2007 Pathfinder
6.
Disconnect lighting and turn signal switch connector. Then while
pressing tabs, pull lighting and turn signal switch toward driver
door to remove.
7.
Remove the screws. Then while pressing the tab, pull the spiral
cable away from steering column assembly.
CAUTION:
●
Do not disassemble spiral cable.
●
Do not apply lubricant to the spiral cable.
8.
Disconnect the spiral cable connectors.
CAUTION:
With the steering linkage disconnected, the spiral cable
may snap by turning the steering wheel beyond the limited
number of turns. The spiral cable can be turned counter-
clockwise about 2.5 turns from the neutral position.
INSTALLATION
Installation is in the reverse order of removal.
●
Align spiral cable correctly when installing steering wheel, refer
to
. Make sure that the spiral cable is in
the neutral position. The neutral position is detected by turning
left 2.6 revolutions from the right end position and ending with
the locating pin at the top.
●
Reset the steering angle sensor calibration after installing spiral
cable. Refer to
BRC-57, "Adjustment of Steering Angle Sensor
●
After the work is completed, perform self-diagnosis to make sure
no malfunction is detected. Refer to
CAUTION:
●
The spiral cable may snap due to steering operation if the cable is not installed in the correct posi-
tion.
●
With the steering linkage disconnected, the cable may snap by turning the steering wheel beyond
the limited number of turns. The spiral cable can be turned counterclockwise about 2.5 turns from
the neutral position.
LHIA0035E
LHIA0036E
LHIA0088E
PHIA0275E
SRS-42
FRONT PASSENGER AIR BAG MODULE
2007 Pathfinder
FRONT PASSENGER AIR BAG MODULE
PFP:K8515
Removal and Installation
EHS001M8
The passenger air bag module originally installed in the vehicle uses direct-connect style harness connectors.
Service replacement passenger air bag modules use tab-locking style harness connectors. If the passenger
air bag module is replaced or if the direct-connect harness connectors are damaged, the vehicle wiring har-
ness must be modified to allow connection of the service replacement passenger air bag module. Refer to
SRS-44, "WIRING HARNESS MODIFICATION"
for wiring harness modification procedure.
REMOVAL
CAUTION:
●
Do not attempt to repair or replace damaged direct-connect front passenger air bag module con-
nectors. If a direct-connect harness connector is damaged, the front passenger air bag must be
replaced and the wiring harness modified.
●
Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.
●
Always work from the side of or under front passenger air bag module.
1.
Disconnect the negative and positive battery cables, then wait at least 3 minutes.
2.
Remove the glove box. Refer to
IP-10, "INSTRUMENT PANEL ASSEMBLY"
.
3.
Remove 2 bolts (through glove box opening) retaining front pas-
senger air bag module to the steering member.
4.
Disconnect the passenger air bag module connectors.
●
For removal/installation of the direct-connect SRS connec-
tors, refer to
SRS-7, "Direct-connect SRS Component Con-
.
5.
Remove the instrument panel assembly from the vehicle. Refer
to
IP-10, "INSTRUMENT PANEL ASSEMBLY"
6.
Remove front passenger air bag module screws then remove
passenger air bag module from instrument panel assembly.
LHIA0093E
WHIA0269E
FRONT PASSENGER AIR BAG MODULE
SRS-43
C
D
E
F
G
I
J
K
L
M
A
B
SRS
2007 Pathfinder
CAUTION:
●
When servicing the SRS, do not work from directly in front
of air bag module.
●
Always place front passenger air bag module with caution
label side facing upward.
●
Do not insert any foreign objects (screwdriver, etc.) into air
bag module or harness connectors.
●
Do not disassemble air bag module.
●
Do not use old nuts after removal; replace with new nuts.
●
Do not expose the front passenger air bag module to tem-
peratures exceeding 90
°
C (194
°
F).
●
Replace the air bag module if it has been dropped or sus-
tained an impact.
●
Do not allow oil, grease or water to come in contact with the
air bag module.
●
For removal/installation of the direct-connect SRS connec-
tors, refer to
SRS-7, "Direct-connect SRS Component Con-
.
INSTALLATION
Original Passenger Air Bag Module
Installation is in the reverse order of removal.
●
For removal/installation of the direct-connect SRS connectors, refer to
SRS-7, "Direct-connect SRS Com-
.
CAUTION:
●
Always work from the side of or under front passenger air bag module.
●
After the work is completed, perform self-diagnosis to check that no malfunction is detected.
Refer to
.
Service Replacement Passenger Air Bag Module
1.
Install the front passenger air bag module to the instrument
panel pad assembly.
2.
Install the instrument panel assembly. Refer to
IP-10, "INSTRUMENT PANEL ASSEMBLY"
.
3.
Connect the front passenger air bag module harness connector to yellow 4-pin service replacement air
bag connector and fasten connector to mounting bracket.
CAUTION:
●
Always work from the side of or under front passenger air bag module.
●
After the work is completed, perform self-diagnosis to check that no malfunction is detected.
Refer to
.
WHIA0111E
SBF814E
WHIA0269E
SRS-44
FRONT PASSENGER AIR BAG MODULE
2007 Pathfinder
WIRING HARNESS MODIFICATION
The passenger air bag module originally installed in the vehicle uses direct-connect style harness connectors.
Service replacement passenger air bag modules use tab-locking style harness connectors. If the passenger
air bag module is replaced or if the direct-connect harness connectors are damaged, the vehicle wiring har-
ness must be modified to allow connection of the service replacement passenger air bag module.
NOTE:
The wiring harness modification is to be performed only if the vehicle is equipped with the original passenger
air bag which uses direct-connect harness connectors. If the passenger air bag is to be replaced in a vehicle
that has already had the service replacement passenger air bag installed, the wiring harness modification is
not required.
CAUTION:
●
Do not attempt to repair or replace damaged direct-connect front passenger air bag module con-
nectors. If a direct-connect harness connector is damaged, the front passenger air bag must be
replaced and the wiring harness modified.
●
Before servicing SRS, turn the ignition switch off, disconnect both battery cables and wait at least
3 minutes.
●
Always work from the side of or under front passenger air bag module.
●
After the work is completed, perform self-diagnosis to check that no malfunction is detected.
Refer to
1.
Locate the yellow and orange direct-connect passenger air bag module harness connectors.
2.
Use wire cutters to cut back both previously used direct-connect passenger air bag module harness con-
nectors from the vehicle wiring harness approximately 50 mm (1.9 in) from the connectors.
3.
Remove approximately 150 mm (5.9 in) of the vehicle harness covering from the cut end.
4.
Slide a piece of dual-wall heat shrink tubing (provided in the pas-
senger air bag service kit) onto each wire of the previously used
vehicle wiring harness.
5.
Fold each wire back and insert into the end of the heat shrink
tubing so that the end of the wire is approximately centered in
the heat shrink tubing.
6.
Use a heat gun to shrink the heat shrink tubing and seal the wire.
7.
Use electrical tape to secure the modified circuits to the outside of the wiring harness.
LHIA0017E
WHIA0062E
FRONT PASSENGER AIR BAG MODULE
SRS-45
C
D
E
F
G
I
J
K
L
M
A
B
SRS
2007 Pathfinder
8.
Locate the front passenger air bag service replacement connec-
tor that is taped back to the main harness. Unwrap the tape to
access the yellow service replacement connector and remove
the dust cover from the connector.
WHIA0118E
SRS-46
SIDE CURTAIN AIR BAG MODULE
2007 Pathfinder
SIDE CURTAIN AIR BAG MODULE
PFP:985P0
Removal and Installation
EHS001M9
REMOVAL
CAUTION:
●
Do not attempt to repair or replace damaged direct-connect SRS component connectors. If a
direct-connect harness connector is damaged, the harness must be replaced.
●
Before servicing the SRS, turn the ignition switch off, disconnect both battery cables and wait at
least 3 minutes.
●
When servicing the SRS, do not work from directly in front of air bag module.
1.
Remove headlining. Refer to
EI-31, "Removal and Installation"
.
2.
Disconnect front and rear side curtain air bag module connectors.
●
For removal/installation of the direct-connect SRS connectors, refer to
3.
Remove the bolts in order starting at the front or rear, and remove the side curtain air bag module.
CAUTION:
●
When servicing the SRS, do not work from directly in front of air bag module.
●
Do not insert any foreign objects (screwdriver, etc.) into air bag module or harness connectors.
●
Do not disassemble air bag module.
●
Do not expose the air bag module to temperatures exceeding 90
°
C (194
°
F).
●
Replace side curtain air bag module if it has been dropped
or sustained an impact.
●
Do not allow oil, grease or water to come in contact with the
air bag module.
INSTALLATION
Installation is in the reverse order of removal.
WHIA0299E
1.
Rear curtain air bag module connector
2.
Front curtain air bag module connector
3.
Sail panel extrusion
SBF814E
SIDE CURTAIN AIR BAG MODULE
SRS-47
C
D
E
F
G
I
J
K
L
M
A
B
SRS
2007 Pathfinder
●
For removal/installation of the direct-connect SRS connectors, refer to
SRS-7, "Direct-connect SRS Com-
.
●
After replacement of side curtain air bag module, perform self-diagnosis to check that no malfunction is
detected. Refer to
.
SRS-48
CRASH ZONE SENSOR
2007 Pathfinder
CRASH ZONE SENSOR
PFP:98531
Removal and Installation
EHS001MA
REMOVAL
CAUTION:
●
Before servicing the SRS, turn the ignition switch off, disconnect both battery cables and wait at
least 3 minutes.
1.
Disconnect the negative and positive battery cables, then wait at least 3 minutes.
2.
Remove crash zone sensor nuts and shield from support mem-
ber.
3.
Disconnect the crash zone sensor harness connector.
4.
Remove crash zone sensor.
CAUTION:
●
Replace crash zone sensor if it has been dropped or sustained an impact.
●
Do not disassemble crash zone sensor.
INSTALLATION
Installation is in the reverse order of removal.
●
After the work is complete, perform self-diagnosis to check that no malfunction is detected. Refer to
LHIA0090E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст