Nissan Pathfinder (2007 year). Manual — part 378
AUTOMATIC DRIVE POSITIONER
SE-63
C
D
E
F
G
H
J
K
L
M
A
B
SE
2007 Pathfinder
3.
CHECK PEDAL ADJUSTING SWITCH
Check continuity between pedal adjusting switch as follows.
OK or NG
OK
>> GO TO 4.
NG
>> Replace pedal adjusting switch.
4.
CHECK PEDAL ADJUSTING SWITCH GROUND CIRCUIT
Check continuity between pedal adjusting switch connector M96 ter-
minal 1 and ground.
OK or NG
OK
>> Check the condition of the harness and connector.
NG
>> Replace or replace harness.
Terminals
Condition
Continuity
2
1
Pedal adjusting switch ON (BACKWARD operation)
Yes
Other than above
No
3
Pedal adjusting switch ON (FORWARD operation)
Yes
Other than above
No
LIIA1014E
1 - Ground
: Continuity should exist.
LIIA1015E
SE-64
AUTOMATIC DRIVE POSITIONER
2007 Pathfinder
Door Mirror Remote Control Switch (Changeover Switch) Circuit Check
EIS007VP
1.
CHECK FUNCTION
With CONSULT-II
Check the operation on “MIR CHNG SW-R” or “MIR CHNG SW-L"
in the DATA MONITOR.
Without CONSULT-II
1.
Turn ignition switch to ACC.
2.
Check voltage between automatic drive positioner control unit
connector and ground.
OK or NG
OK
>> Door mirror remote control switch (changeover switch) is OK.
NG
>> GO TO 2.
2.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH CIRCUIT HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit and door mir-
ror remote control switch.
3.
Check continuity between automatic drive positioner control unit
connector M33 terminals 2, 18 and door mirror remote control
switch connector M159 terminals 2, 3.
4.
Check continuity between automatic drive positioner control unit
connector M33 terminals 2, 18 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
Monitor item [OPERATION or
UNIT]
Contents
MIR CHNG SW-R
“ON/OFF”
ON/OFF status judged from the changeover
switch (switching to RIGHT) signal is displayed.
MIR CHNG SW-L
“ON/OFF”
ON/OFF status judged from the changeover
switch (switching to LEFT) signal is displayed.
PIIA0191E
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(-)
M33
2
Ground
Changeover switch
RIGHT position
0
Other than above
5
18
Changeover switch
LEFT position
0
Other than above
5
PIIA4767E
2 - 3
: Continuity should exist.
18 - 2
: Continuity should exist.
2 - Ground
: Continuity should not exist.
18 - Ground
: Continuity should not exist.
LIIA1821E
AUTOMATIC DRIVE POSITIONER
SE-65
C
D
E
F
G
H
J
K
L
M
A
B
SE
2007 Pathfinder
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH (CHANGEOVER SWITCH)
Check continuity between door mirror remote control switch as fol-
lows.
OK or NG
OK
>> Replace automatic drive positioner control unit.
NG
>> Replace door mirror remote control switch.
Door Mirror Remote Control Switch (Mirror Switch) Circuit Check
EIS007VQ
1.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH (MIRROR SWITCH) SIGNAL
With CONSULT-II
Check the operation on “MIR CON SW–UP/DN” and
“MIR CON SW-RH/LH” in the DATA MONITOR.
Without CONSULT-II
1.
Turn ignition switch to ACC.
2.
Check voltage between automatic drive positioner control unit
connector and ground.
OK or NG
OK
>> Door mirror remote control switch (mirror switch) circuit is OK.
NG
>> GO TO 2.
Terminals
Condition
Continuity
3
13
Changeover switch RIGHT position
Yes
Other than above
No
2
Changeover switch LEFT position
Yes
Other than above
No
LIIA2052E
Monitor item [OPERATION or
UNIT]
Contents
MIR CON SW-UP
“ON/
OFF”
ON/OFF status judged from the mirror switch
(UP) signal is displayed.
MIR CON SW-DN
“ON/
OFF”
ON/OFF status judged from the mirror switch
(DOWN) signal is displayed.
MIR CON SW-RH
“ON/
OFF”
ON/OFF status judged from the mirror switch
(RIGHT) signal is displayed.
MIR CON SW-LH
“ON/
OFF”
ON/OFF status judged from the mirror switch
(LEFT) signal is displayed.
PIIA0199E
Connector
Terminals
Condition
Voltage (V)
(Approx.)
(+)
(-)
M33
3
Ground
Mirror switch UP operation
0
Other than above
5
4
Mirror switch LEFT operation
0
Other than above
5
19
Mirror switch DOWN operation
0
Other than above
5
20
Mirror switch RIGHT operation
0
Other than above
5
PIIA4771E
SE-66
AUTOMATIC DRIVE POSITIONER
2007 Pathfinder
2.
CHECK HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit and door mir-
ror remote control switch.
3.
Check continuity between automatic drive positioner control unit
connector M33 terminals 3, 4, 19, 20 and door mirror remote
control switch connector M159 terminals 4, 5, 6, 14.
4.
Check continuity between automatic drive positioner control unit connector M33 terminals 3, 4, 19, 20 and
ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
3.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH (MIRROR SWITCH)
Check continuity between door mirror remote control switch as follows.
OK or NG
OK
>> Replace automatic drive positioner control unit.
NG
>> Replace door mirror remote control switch.
3 - 6
: Continuity should exist.
4 - 5
: Continuity should exist.
19 - 14
: Continuity should exist.
20 - 4
: Continuity should exist.
3 - Ground
: Continuity should not exist.
4 - Ground
: Continuity should not exist.
19 - Ground
: Continuity should not exist.
20 - Ground
: Continuity should not exist.
LIIA1823E
Terminals
Switch condition
Continuity
4
13
Mirror switch RIGHT operation
Yes
Other than above
No
5
Mirror switch LEFT operation
Yes
Other than above
No
6
Mirror switch UP operation
Yes
Other than above
No
14
Mirror switch DOWN operation
Yes
Other than above
No
LIIA2053E
AUTOMATIC DRIVE POSITIONER
SE-67
C
D
E
F
G
H
J
K
L
M
A
B
SE
2007 Pathfinder
Door Mirror Remote Control Switch Ground Circuit Inspection
EIS007VR
1.
CHECK DOOR MIRROR REMOTE CONTROL SWITCH GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect door mirror remote control switch.
3.
Check continuity between door mirror remote control switch con-
nector M159 terminal 13 and ground.
OK or NG
OK
>> Check the condition of the harness and the connector.
NG
>> Repair or replace harness.
Seat Memory Switch Circuit Inspection
EIS007VS
1.
CHECK FUNCTION
With CONSULT-II
With “SET SW, MEMORY SW1, MEMORY SW2” on the DATA
MONITOR, operate the switch to check ON/OFF operation.
Without CONSULT-II
OK or NG
OK
>> Seat memory switch circuit is OK.
NG
>> GO TO 2.
13 - Ground
: Continuity should exist.
LIIA1825E
Monitor item [OPERATION or
UNIT]
Contents
MEMORY SW1
“ON/OFF”
ON/OFF status judged from the seat memory
switch 1 signal is displayed.
MEMORY SW2
“ON/OFF”
ON/OFF status judged from the seat memory
switch 2 signal is displayed.
SET SW
“ON/OFF”
ON/OFF status judged from the setting
switch signal is displayed.
Con-
nector
Terminal
Condition
Voltage (V)
(Approx.)
+
-
D5
1
4
Memory switch 1 ON
0
Memory switch 1: OFF
5
2
Memory switch 2: ON
0
Memory switch 2: OFF
5
3
Set switch: ON
0
Set switch: OFF
5
PIIA0309E
SE-68
AUTOMATIC DRIVE POSITIONER
2007 Pathfinder
2.
CHECK SEAT MEMORY SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect seat memory switch.
3.
Operate the setting switch and seat memory switch.
4.
Check continuity between seat memory switch as follows.
OK or NG
OK
>> GO TO 3.
NG
>> Replace seat memory switch.
3.
CHECK HARNESS CONTINUITY
1.
Disconnect automatic drive positioner control unit.
2.
Check continuity between automatic drive positioner control unit
connector M33 terminals 9, 24, 25 and seat memory switch con-
nector D5 terminals 1, 2, 3.
3.
Check continuity between automatic drive positioner control unit
connector M41 terminals 9, 24, 25 and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace harness.
4.
CHECK SEAT MEMORY SWITCH GROUND CIRCUIT
Check continuity between seat memory switch D5 terminal 4 and
ground.
OK or NG
OK
>> Replace automatic drive positioner control unit.
NG
>> Repair or replace harness.
Terminal
Condition
Continuity
1
4
Memory switch 1 ON
Yes
Memory switch 1: OFF
No
2
Memory switch 2: ON
Yes
Memory switch 2: OFF
No
3
Set switch: ON
Yes
Set switch: OFF
No
LIIA1020E
9 - 1
: Continuity should exist.
24 - 3
: Continuity should exist.
25 - 2
: Continuity should exist.
9 - Ground
: Continuity should not exist.
24 - Ground
: Continuity should not exist.
25- Ground
: Continuity should not exist.
PIIA4576E
4 - Ground
: Continuity should exist.
PIIA4821E
AUTOMATIC DRIVE POSITIONER
SE-69
C
D
E
F
G
H
J
K
L
M
A
B
SE
2007 Pathfinder
Seat Memory Indicator Lamp Circuit Inspection
EIS007VT
1.
CHECK FUNCTION
With CONSULT-II
With “MEMORY SW INDCTR” in ACTIVE TEST, check operation.
Without CONSULT-II
GO TO 2.
OK or NG
OK
>> Seat memory switch indicator lamp circuit is OK.
NG
>> GO TO 2.
2.
CHECK SEAT MEMORY SWITCH POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect seat memory switch.
3.
Turn ignition switch ON.
4.
Check voltage between seat memory switch connector D5 ter-
minal 5 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Repair or replace harness.
3.
CHECK SEAT MEMORY INDICATOR CIRCUIT HARNESS CONTINUITY
1.
Turn ignition switch OFF.
2.
Disconnect automatic drive positioner control unit.
3.
Check continuity between automatic drive positioner control unit
connector M33 terminals 12, 13 and seat memory switch con-
nector D5 terminals 6, 7.
4.
Check continuity between automatic drive positioner control unit
connector M33 terminals 12, 13 and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Repair or replace harness.
Test item
Description
MEMORY SW INDCTR
The memory switch indicator is lit by receiving the
drive signal.
PIIA0319E
5 - Ground
: Battery voltage
PIIA4595E
12 - 6
: Continuity should exist.
13 - 7
: Continuity should exist.
12 - Ground
: Continuity should not exist.
13 - Ground
: Continuity should not exist.
LIIA1022E
SE-70
AUTOMATIC DRIVE POSITIONER
2007 Pathfinder
4.
CHECK SEAT MEMORY SWITCH INDICATOR SIGNAL
1.
Connect seat memory switch.
2.
Check voltage between automatic drive positioner control unit
connector M33 terminals 12, 13 and ground.
OK or NG
OK
>> Replace automatic drive positioner control unit.
NG
>> Replace seat memory switch.
Door Mirror Sensor Power Supply and Ground Circuit inspection
EIS007VU
1.
CHECK DOOR MIRROR SENSOR CIRCUIT HARNESS CONTINUITY
1.
Disconnect automatic drive positioner control unit and door mir-
ror (LH and RH).
2.
Check continuity between automatic drive positioner control unit
connector M34 terminals 33, 41 and door mirror connector D4
(LH), D107 (RH) terminals 4, 9.
3.
Check continuity between automatic drive positioner control unit
connector M34 terminals 33, 41 and ground.
OK or NG
OK
>> GO TO 2.
NG
>> Repair or replace harness.
2.
CHECK MIRROR SENSOR POWER SUPPLY
1.
Connect automatic drive positioner control unit and door mirror
LH.
2.
Turn ignition switch to ACC.
3.
Check voltage between automatic drive positioner control unit
connector M34 terminal 33 and ground.
OK or NG
OK
>> GO TO 3.
NG
>> Replace automatic drive positioner control unit.
12 - Ground
: Battery voltage
13 - Ground
: Battery voltage
LIIA2237E
33 - 4
: Continuity should exist.
41 - 9
: Continuity should exist.
33 - Ground
: Continuity should not exist.
41 - Ground
: Continuity should not exist.
LIIA1773E
33 - Ground
: Approx. 5V
LIIA1136E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст