Nissan Pathfinder (2007 year). Manual — part 295
LT-1
LIGHTING SYSTEM
K ELECTRICAL
CONTENTS
C
D
E
F
G
H
I
J
L
M
SECTION
LT
A
B
LT
2007 Pathfinder
PRECAUTIONS . . . . . . . . . . . . . . .. 4
HEADLAMP (FOR USA) . . . . . . . . . . . 5
Component Parts and Harness Connector Location
System Description . . . . . . . . . . . . .. 5
CONSULT-II Function (BCM) . . . . . . . . . 12
CONSULT-II Function (IPDM E/R) . . . . . . . 13
LOW BEAM AND HIGH BEAM . . . . . . ... 24
Bulb Replacement . . . . . . . . . . . . .. 25
Removal and Installation . . . . . . . . . . 25
FRONT COMBINATION LAMP . . . . . . ... 25
Disassembly and Assembly . . . . . . . . . 26
FRONT COMBINATION LAMP . . . . . . ... 26
HEADLAMP (FOR CANADA) - DAYTIME LIGHT
SYSTEM - . . . . . . . . . . . . . . . . .. 27
LT-2
2007 Pathfinder
CONSULT-II Function (BCM) . . . . . . . . .. 45
CONSULT-II Function (IPDM E/R) . . . . . . .. 46
OPTICAL SENSOR . . . . . . . . . . . . 50
FRONT FOG LAMP . . . . . . . . . . . . .. 51
FRONT FOG LAMP . . . . . . . . . . . . 59
TURN SIGNAL AND HAZARD WARNING LAMPS ... 60
Component Parts and Harness Connector Location ...60
System Description . . . . . . . . . . . . .60
CHECK POWER SUPPLY AND GROUND CIR-
CUIT FOR BCM . . . . . . . . . . . . ...65
CONSULT-II Function (BCM) . . . . . . . . ..65
FRONT TURN SIGNAL LAMP . . . . . . . .70
REAR TURN SIGNAL LAMP . . . . . . . ...70
Removal and Installation . . . . . . . . . . .70
FRONT TURN SIGNAL LAMP . . . . . . . .70
REAR TURN SIGNAL LAMP . . . . . . . ...70
LIGHTING AND TURN SIGNAL SWITCH . . . . 71
Removal and Installation . . . . . . . . . . .71
REMOVAL . . . . . . . . . . . . . . . 71
INSTALLATION . . . . . . . . . . . . . 71
HAZARD SWITCH . . . . . . . . . . . . . .72
Removal and Installation . . . . . . . . . . .72
REMOVAL . . . . . . . . . . . . . . . 72
INSTALLATION . . . . . . . . . . . . . 72
COMBINATION SWITCH . . . . . . . . . . ..73
CONSULT-II START PROCEDURE . . . . . .74
DATA MONITOR . . . . . . . . . . . . ..74
STOP LAMP . . . . . . . . . . . . . . . ..78
BULB REPLACEMENT . . . . . . . . . . 80
REMOVAL AND INSTALLATION . . . . . . .80
Stop Lamp . . . . . . . . . . . . . . . ...80
BULB REPLACEMENT . . . . . . . . . . 80
REMOVAL AND INSTALLATION . . . . . . .80
LT-3
C
D
E
F
G
H
I
J
L
M
A
B
LT
2007 Pathfinder
Bulb Replacement . . . . . . . . . . . . .. 82
Removal and Installation . . . . . . . . . . 82
PARKING, LICENSE PLATE AND TAIL LAMPS . . 83
Component Parts and Harness Connector Location
System Description . . . . . . . . . . . . 83
OPERATION BY LIGHTING SWITCH . . . . 83
COMBINATION SWITCH READING FUNCTION
EXTERIOR LAMP BATTERY SAVER CONTROL
Removal and Installation . . . . . . . . . . 97
LICENSE PLATE LAMP . . . . . . . . . .. 97
REAR COMBINATION LAMP . . . . . . . . .. 98
Bulb Replacement . . . . . . . . . . . . .. 98
REMOVAL . . . . . . . . . . . . . . ... 98
INSTALLATION . . . . . . . . . . . . ... 98
Removal and Installation . . . . . . . . . . 98
REMOVAL . . . . . . . . . . . . . . ... 98
INSTALLATION . . . . . . . . . . . . ... 98
TRAILER TOW . . . . . . . . . . . . . . . 99
Component Parts and Harness Connector Location
System Description . . . . . . . . . . . . 99
TRAILER POWER SUPPLY OPERATION . . 100
Schematic . . . . . . . . . . . . . . . . 102
Wiring Diagram — T/TOW — . . . . . . . ... 103
INTERIOR ROOM LAMP . . . . . . . . . . 108
Component Parts and Harness Connector Location .108
System Description . . . . . . . . . . . ... 109
INSPECTION FOR POWER SUPPLY AND
GROUND CIRCUIT FOR BCM . . . . . . . 119
CONSULT-II Function (BCM) . . . . . . . ... 119
ILLUMINATION . . . . . . . . . . . . . ... 126
Component Parts and Harness Connector Location .126
System Description . . . . . . . . . . . ... 126
ILLUMINATION CONTROL SWITCH . . . . 141
LT-4
PRECAUTIONS
2007 Pathfinder
PRECAUTIONS
PFP:00011
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
EKS00FTW
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
●
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
●
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
●
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
General precautions for service operations
EKS00FTX
●
Never work with wet hands.
●
Turn the lighting switch OFF before disconnecting and connecting the connector.
●
When checking the headlamp on/off operation, check it on vehicle and with the power connected to the
vehicle-side connector.
●
Do not touch the headlamp bulb glass surface with bare hands or allow oil or grease to get on it. Do not
touch the headlamp bulb just after the headlamp is turned off, because it is very hot.
●
When the bulb has burned out, wrap it in a thick vinyl bag and discard. Do not break the bulb.
●
Leaving the bulb removed from the headlamp housing for a long period of time can deteriorate the perfor-
mance of the lens and reflector (dirt, clouding). Always prepare a new bulb and have it on hand when
replacing the bulb.
●
Do not use organic solvent (paint thinner or gasoline) to clean lamps and to remove old sealant.
HEADLAMP (FOR USA)
LT-5
C
D
E
F
G
H
I
J
L
M
A
B
LT
2007 Pathfinder
HEADLAMP (FOR USA)
PFP:26010
Component Parts and Harness Connector Location
EKS00FTZ
System Description
EKS00FU0
Control of the front headlamp system operation is dependent upon the position of the combination switch
(lighting switch). When the lighting switch is placed in the 2ND position, the BCM (body control module)
receives input requesting the headlamps (and tail lamps) illuminate. This input is communicated to the IPDM
E/R (intelligent power distribution module engine room) across the CAN communication lines. The CPU (cen-
tral processing unit) of the IPDM E/R controls the front headlamp high and front headlamp low relay coils.
When energized, these relays direct power to the respective headlamps, which then illuminate.
OUTLINE
Power is supplied at all times
●
to ignition relay, located in the IPDM E/R,
●
to headlamp high relay, located in the IPDM E/R,
●
to headlamp low relay, located in the IPDM E/R,
●
through 20A fuse (No. 53, located in the IPDM E/R)
●
to CPU of the IPDM E/R, and
●
through 50A fusible link (letter g , located in the fuse and fusible link box)
●
to BCM terminal 70.
With the ignition switch in the ON or START position, power is supplied
●
to ignition relay, located in the IPDM E/R, and
●
through 10A fuse [No. 1, located in the fuse block (J/B)]
●
to BCM terminal 38.
Ground is supplied
●
to BCM terminal 67
●
through grounds M57, M61 and M79, and
●
to IPDM E/R terminals 38 and 59
●
through grounds E9, E15 and E24.
WKIA4957E
1.
IPDM E/R
E118, E119, E120, E121,
E122, E123, E124
2.
BCM
M18, M19, M20
(view with instrument lower panel LH removed
3.
Combination Switch (lighting switch)
M28
4.
Combination meter
M24
LT-6
HEADLAMP (FOR USA)
2007 Pathfinder
Low Beam Operation
With the lighting switch in 2ND position, the BCM receives input requesting the headlamps to illuminate. This
input is communicated to the IPDM E/R across the CAN communication lines. The CPU of the IPDM E/R con-
trols the headlamp low relay coil. When energized, this relay directs power
●
through 15A fuse (No. 41, located in the IPDM E/R)
●
through IPDM E/R terminal 54
●
to front headlamp RH terminal 3, and
●
through 15A fuse (No. 40, located in the IPDM E/R)
●
through IPDM E/R terminal 52
●
to front headlamp LH terminal 3.
Ground is supplied
●
to front headlamp LH and RH terminal 2
●
through grounds E9, E15 and E24.
With power and ground supplied, low beam headlamps illuminate.
High Beam Operation/Flash-to-Pass Operation
With the lighting switch in 2ND position and placed in HIGH or PASS position, the BCM receives input request-
ing the headlamp high beams to illuminate. This input is communicated to the IPDM E/R across the CAN com-
munication lines. The CPU of the combination meter controls the ON/OFF status of the HIGH BEAM indicator.
The CPU of the IPDM E/R controls the headlamp high relay coil. When energized, this relay directs power
●
through 10A fuse (No. 34, located in the IPDM E/R)
●
through IPDM E/R terminal 56
●
to front headlamp RH terminal 1, and
●
through 10A fuse (No. 35, located in the IPDM E/R)
●
through IPDM E/R terminal 55
●
to front headlamp LH terminal 1.
Ground is supplied
●
to front headlamp LH and RH terminal 2
●
through grounds E9, E15 and E24.
With power and ground supplied, the high beam headlamps illuminate.
BATTERY SAVER CONTROL
When the combination switch (lighting switch) is in the 2ND position (ON), and the ignition switch is turned
from ON or ACC to OFF, the battery saver control feature is activated.
Under this condition, the headlamps remain illuminated for 5 minutes, unless the combination switch (lighting
switch) position is changed. If the combination switch (lighting switch) position is changed, then the headlamps
are turned off.
AUTO LIGHT OPERATION
Refer to
VEHICLE SECURITY SYSTEM (PANIC ALARM)
The vehicle security system (panic alarm) will flash the high beams if the system is triggered. Refer to
CAN Communication System Description
EKS00FU1
Refer to
HEADLAMP (FOR USA)
LT-7
C
D
E
F
G
H
I
J
L
M
A
B
LT
2007 Pathfinder
Schematic
EKS00FU2
WKWA5434E
LT-8
HEADLAMP (FOR USA)
2007 Pathfinder
Wiring Diagram — H/LAMP —
EKS00FU3
WKWA5435E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст