Nissan Pathfinder (2007 year). Manual — part 304
COMBINATION SWITCH
LT-73
C
D
E
F
G
H
I
J
L
M
A
B
LT
2007 Pathfinder
COMBINATION SWITCH
PFP:25567
Wiring Diagram — COMBSW —
EKS00FWB
WKWA5442E
LT-74
COMBINATION SWITCH
2007 Pathfinder
Combination Switch Reading Function
EKS00FWC
For details, refer to
BCS-3, "COMBINATION SWITCH READING FUNCTION"
CONSULT-II Function (BCM)
EKS00FWD
Refer to
LT-12, "CONSULT-II Function (BCM)"
CONSULT-II START PROCEDURE
Refer to
GI-38, "CONSULT-II Start Procedure"
DATA MONITOR
Display Item List
Monitor item name
"OPERATION OR UNIT"
Contents
TURN SIGNAL R
"ON/OFF"
Displays "Turn Right (ON)/Other (OFF)" status, determined from lighting switch signal.
TURN SIGNAL L
"ON/OFF"
Displays "Turn Left (ON)/Other (OFF)" status, determined from lighting switch signal.
HI BEAM SW
"ON/OFF"
Displays status (high beam switch: ON/Others: OFF) of high beam switch judged from lighting
switch signal.
HEAD LAMP SW 1
"ON/OFF"
Displays "Headlamp switch 1 (ON)/Other (OFF)" status, determined from lighting switch signal.
HEAD LAMP SW 2
"ON/OFF"
Displays status (headlamp switch 2: ON/Others: OFF) of headlamp switch 2 judged from lighting
switch signal.
LIGHT SW 1ST
"ON/OFF"
Displays status (lighting switch 1st position: ON/Others: OFF) of lighting switch judged from lighting
switch signal.
PASSING SW
"ON/OFF"
Displays status (flash-to-pass switch: ON/Others: OFF) of flash-to-pass switch judged from lighting
switch signal.
AUTO LIGHT SW
"ON/OFF"
Displays "Auto light switch (ON)/Other (OFF)" status, determined from lighting switch signal.
FR FOG SW
"ON/OFF"
Displays "Front fog lamp switch (ON)/Other (OFF)" status, determined from lighting switch signal.
FR WIPER HI
"ON/OFF"
Displays "Front Wiper HI (ON)/Other (OFF)" status, determined from wiper switch signal.
FR WIPER LOW
"ON/OFF"
Displays "Front Wiper LOW (ON)/Other (OFF)" status, determined from wiper switch signal.
FR WIPER INT
"ON/OFF"
Displays "Front Wiper INT (ON)/Other (OFF)" status, determined from wiper switch signal.
FR WASHER SW
"ON/OFF"
Displays "Front Washer Switch (ON)/Other (OFF)" status, determined from wiper switch signal.
INT VOLUME
[1 - 7]
Displays intermittent operation knob setting (1 - 7), determined from wiper switch signal.
RR WIPER ON
"ON/OFF"
Displays "Rear Wiper (ON)/(OFF)" status, determined from wiper switch signal.
RR WIPER INT
"ON/OFF"
Displays "Rear Wiper INT (ON)/(OFF)" status, determined from wiper switch signal.
RR WASHER SW
"ON/OFF" Displays "Rear Washer (ON)/(OFF)" status, determined from wiper switch signal.
COMBINATION SWITCH
LT-75
C
D
E
F
G
H
I
J
L
M
A
B
LT
2007 Pathfinder
Combination Switch Inspection
EKS00FWE
1.
SYSTEM CHECK
Referring to table below, check to which system the malfunctioning switch belongs.
>> GO TO 2.
2.
SYSTEM CHECK
With CONSULT-II
CAUTION:
If CONSULT-II is used with no connection of CONSULT-II CONVERTER, malfunctions might be
detected in self-diagnosis depending on control unit which carries out CAN communication.
1.
Connect CONSULT-II, and select "COMB SW" on "SELECT
TEST ITEM" screen.
2.
Select "DATA MONITOR".
3.
Select "START", and confirm that other switches in malfunction-
ing system operate normally.
Example: When auto light switch is malfunctioning, confirm that
"FRONT WIPER LOW" and "FRONT WIPER INT" in System 3,
to which the auto light switch belongs, turn ON-OFF normally.
Without CONSULT-II
Operate combination switch, and confirm that other switches in malfunctioning system operate normally.
Example: When auto light switch is malfunctioning, confirm that "FRONT WIPER LOW" and "FRONT WIPER
INT" in System 3, to which the auto light switch belongs, operate normally.
Check results
Other switches in malfunctioning system operate normally.>>Replace lighting switch or wiper switch.
Other switches in malfunctioning system do not operate normally.>>GO TO 3.
System 1
System 2
System 3
System 4
System 5
—
FR WASHER
FR WIPER LO
TURN LH
TURN RH
FR WIPER HI
—
FR WIPER INT
PASSING
HEAD LAMP1
INT VOLUME 1
RR WASHER
—
HEAD LAMP2
HI BEAM
RR WIPER INT
INT VOLUME 3
AUTO LIGHT
—
TAIL LAMP
INT VOLUME 2
RR WIPER ON
—
FR FOG
—
SKIA7075E
LT-76
COMBINATION SWITCH
2007 Pathfinder
3.
HARNESS INSPECTION
1.
Turn ignition switch OFF.
2.
Disconnect BCM and combination switch connectors.
3.
Check for continuity between BCM harness connector of the suspect system and the corresponding com-
bination switch connector terminals.
4.
Check for continuity between each terminal of BCM harness connector in suspect malfunctioning system
and ground.
OK or NG
OK
>> GO TO 4.
NG
>> Check harness between BCM and combination switch for open or short circuit.
Sus-
pect
system
A
B
Continuity
BCM
connector
Terminal
Combina-
tion switch
connector
Terminal
1
M18
Input 1
6
M28
6
Yes
Output 1
36
1
2
Input 2
5
7
Output 2
35
2
3
Input 3
4
10
Output 3
34
3
4
Input 4
3
9
Output 4
33
4
5
Input 5
2
8
Output 5
32
5
Suspect
system
A
Continuity
BCM
connector
Terminal
1
A: M18
Input 1
6
Ground
No
Output 1
36
2
Input 2
5
Output 2
35
3
Input 3
4
Output 3
34
4
Input 4
3
Output 4
33
5
Input 5
2
Output 5
32
WKIA5841E
COMBINATION SWITCH
LT-77
C
D
E
F
G
H
I
J
L
M
A
B
LT
2007 Pathfinder
4.
BCM OUTPUT TERMINAL INSPECTION
1.
Connect BCM and combination switch connectors.
2.
Turn lighting switch and wiper switch to OFF.
3.
Set wiper dial to position 4.
4.
Turn ignition switch ON, and check combination switch input
(BCM output) terminal voltage waveform of suspect malfunction-
ing system.
OK or NG
OK
>> Open circuit in combination switch, GO TO 5.
NG
>> Replace BCM. Refer to
BCS-25, "Removal and Installa-
5.
COMBINATION SWITCH INSPECTION
Referring to table below, perform combination switch inspection.
>> Inspection End.
Removal and Installation
EKS00FWF
For details, refer to
LT-71, "Removal and Installation"
Switch Circuit Inspection
EKS00FWG
For details, refer to
LT-75, "Combination Switch Inspection"
.
Suspect system
Combination switch
(+)
Connector
Terminal
1
M28
Input 1
1
2
Input 2
2
3
Input 3
3
4
Input 4
4
5
Input 5
5
WKIA5842E
Procedure
1
2
3
4
5
6
7
Replace
lighting
switch.
Confirm
check
results.
OK
INSPECTION END
Confirm
check
results.
OK
INSPECTION END
Confirm
check
results.
OK
INSPECTION END
NG
Replace wiper
switch.
NG
Replace switch
base.
NG
Confirm symptom
again.
LT-78
STOP LAMP
2007 Pathfinder
STOP LAMP
PFP:26550
System Description
EKS00FWH
Power is supplied at all times
●
through 10A fuse [No. 20, located in fuse block (J/B)]
●
to stop lamp switch terminal 1, and
●
to stop lamp relay terminals 2 and 3 (with hill descent control and hill start assist).
When the brake pedal is pressed, the stop lamp switch is closed and power is supplied
●
through stop lamp switch terminal 2
●
to rear combination lamp LH and RH terminal 2
●
to high-mounted stop lamp terminal 1
●
to ABS actuator and electric unit (control unit) terminal 41.
Ground is supplied
●
to rear combination lamp LH terminal 5
●
through grounds B7 and B19, and
●
to high-mounted stop lamp terminal 2
●
through grounds D406 and D504, and
●
to rear combination lamp RH terminal 5
●
through grounds B117 and B132.
With power and ground supplied, the stop lamps illuminate.
STOP LAMP
LT-79
C
D
E
F
G
H
I
J
L
M
A
B
LT
2007 Pathfinder
Wiring Diagram — STOP/L —
EKS00FWI
WKWA4341E
LT-80
STOP LAMP
2007 Pathfinder
High-Mounted Stop Lamp
EKS00FWJ
BULB REPLACEMENT
The high-mounted stop lamp bulbs are not serviceable.
REMOVAL AND INSTALLATION
Removal
1.
Remove back door window garnish.
2.
Disconnect high-mounted stop lamp connector.
3.
Remove nuts and remove high-mounted stop lamp.
Installation
Installation is in the reverse order of removal.
Stop Lamp
EKS00FWK
BULB REPLACEMENT
Refer to
REMOVAL AND INSTALLATION
Refer to
LT-98, "Removal and Installation"
.
LKIA0576E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст