Nissan Pathfinder (2007 year). Manual — part 288
TROUBLE DIAGNOSES WORK FLOW
LAN-35
[CAN FUNDAMENTAL]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
2007 Pathfinder
3.
CAN DIAG SUPPORT MNTR (without PAST): Check the CAN DIAG SUPPORT MNTR (without PAST) of
units indicating “U1000” or “U1001” on SELF-DIAG RESULTS. Draw a line on the diagnosis sheet to indi-
cate the possible error circuit.
NOTE:
●
While an error occurred in the past according to SELF-DIAG RESULTS, it is unclear which signal is not
received. Assume that errors were detected from all reception items.
●
Draw a single line among the unit and all reception items. (Work flow differs from CAN DIAG SUPPORT
MNTR (with PAST).)
a.
Reception item of “EPS”: Assume that the unit could not receive the signals from ECM, ABS, and M&A.
Draw a line among EPS, ECM, ABS, and M&A (line 3-a in the figure).
b.
Reception item of “ABS”: Assume that the unit could not receive the signal from ECM. Draw a line
between ABS and ECM (line 3-b in the figure).
SKIB8733E
LAN-36
[CAN FUNDAMENTAL]
TROUBLE DIAGNOSES WORK FLOW
2007 Pathfinder
4.
Search for the possible cause using CAN communication signal chart using information from the interview
with the customer.
NOTE:
For the details of CAN communication signal, refer to
LAN-50, "CAN Communication Signal Chart"
a.
ABS warning lamp turned ON and speedometer did not move: This means that “ABS warning lamp signal”
and “Vehicle speed signal” could not communicate between M&A and ABS (4-a in the figure).
b.
The tachometer moved normally: This means that “Engine speed signal” could communicate normally
between ECM and M&A (4-b in the figure).
SKIB8895E
TROUBLE DIAGNOSES WORK FLOW
LAN-37
[CAN FUNDAMENTAL]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
2007 Pathfinder
5.
Fill out the diagnosis sheet based on information from step 4.
a.
The ABS warning lamp turned ON and speedometer did not move: Assume that a possible cause is no
communication between M&A and ABS. Draw a line between M&A and ABS. (Line 5-a in the figure).
b.
The tachometer moved normally: Put check marks between ECM and M&A. The circuit between ECM and
M&A is functioning properly (check marks 5-b in the figure).
SKIB8735E
LAN-38
[CAN FUNDAMENTAL]
TROUBLE DIAGNOSES WORK FLOW
2007 Pathfinder
6.
The circuit which has the most amount of lines are the possible cause. Error is detected from ABS actua-
tor and electric unit (control unit) branch line (shaded in the figure).
NOTE:
For abbreviations, refer to
7.
Perform the inspection procedure for the possible cause. Refer to
LAN-75, "Malfunction Area Chart"
SKIB8896E
TROUBLE DIAGNOSES WORK FLOW
LAN-39
[CAN FUNDAMENTAL]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
2007 Pathfinder
Past Error — Short Circuit —
When the symptoms listed below exist, a short circuit of the CAN communication line is a possible cause.
Item (CONSULT-II)
Indication
Inspection procedure
SELF-DIAG RESULTS
“U1000” and “U1001” is indicated in the past for most units.
Refer to
CAN DIAG SUPPORT MNTR
Only on CAN DIAG SUPPORT MNTR (with PAST), “1 - 39” is
indicated on “PAST” of “TRANSMIT DIAG” and the reception
item.
SKIB8897E
LAN-40
[CAN]
INDEX FOR DTC
2007 Pathfinder
INDEX FOR DTC
PFP:00004
DTC No. Index
UKS006HF
DTC
Self-diagnosis item
(CONSULT-II indication)
DTC detection condition
Inspection
U1000
CAN COMM CIRCUIT
When ECM is not transmitting or receiving CAN
communication signal of OBD (emission-related
diagnosis) for 2 seconds or more.
Refer to
When a control unit (except for ECM) is not
transmitting or receiving CAN communication
signal for 2 seconds or more.
U1001
CAN COMM CIRCUIT
When ECM is not transmitting or receiving CAN
communication signal other than OBD (emis-
sion-related diagnosis) for 2 seconds or more.
U1002
SYSTEM COMM
When a control unit is not transmitting or receiv-
ing CAN communication signal for 2 seconds or
less.
Start the inspection.
Refer to the applicable
section of the indicated
control unit.
U1010
CONTROL UNIT [CAN]
When an error is detected during the initial diag-
nosis for CAN controller of each control unit.
Replace the control unit
indicating “U1010”.
HOW TO USE THIS SECTION
LAN-41
[CAN]
C
D
E
F
G
H
I
J
L
M
A
B
LAN
2007 Pathfinder
HOW TO USE THIS SECTION
PFP:00008
Caution
UKS006HG
●
This section describes information peculiar to a vehicle, sheets for trouble diagnosis, and inspection pro-
cedures.
●
For trouble diagnosis procedure, refer to
LAN-17, "Trouble Diagnosis Procedure"
Abbreviation List
UKS006HH
Abbreviations in CAN communication signal chart, and the diagnosis sheet are as per the following list.
Abbreviation
Unit name
SELECT SYSTEM
(CONSULT-II)
CAN DIAG SUPPORT MNTR
(CONSULT-II)
4WD
Transfer control unit
ALL MODE AWD/4WD
AWD/4WD
A-BAG
Air bag diagnosis sensor unit
AIR BAG
—
ABS
ABS actuator and electric unit (control unit)
ABS
VDC/TCS/ABS
ADP
Driver seat control unit
AUTO DRIVE POS.
—
BCM
BCM
BCM
BCM/SEC
DISP
Display control unit
—
—
DLC
Data link connector
—
—
ECM
ECM
ENGINE
ECM
HVAC
Front air control
—
—
IPDM-E
IPDM E/R
IPDM E/R
IPDM E/R
M&A
Combination meter
METER
METER/M&A
STRG
Steering angle sensor
—
STRG
TCM
TCM
A/T
TCM
LAN-42
[CAN]
PRECAUTIONS
2007 Pathfinder
PRECAUTIONS
PFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
UKS006HI
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
●
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
●
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
●
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions When Using CONSULT-II
UKS006HJ
Use CONSULT-II CONVERTER when connecting CONSULT-II to data link connector.
CAUTION:
CAN communication does not function properly if CONSULT-II is used without connecting CONSULT-II
CONVERTER.
Precautions for Trouble Diagnosis
UKS006HK
CAUTION:
●
Never apply 7.0 V or more to the measurement terminal.
●
Use a tester with open terminal voltage of 7.0 V or less.
●
Turn the ignition switch OFF and disconnect the battery cable from the negative terminal when
checking the harness.
Precautions for Harness Repair
UKS006HL
●
Solder the repaired area and wrap tape around the soldered
area.
NOTE:
A fray of twisted lines must be within 110 mm (4.33 in).
SKIB8766E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст