Nissan Pathfinder (2007 year). Manual — part 381
FRONT SEAT
SE-87
C
D
E
F
G
H
J
K
L
M
A
B
SE
2007 Pathfinder
7.
Seat cushion frame
8.
Seat cushion inner finisher
9.
Seat belt buckle assembly
10. Seat frame assembly
11. Leg cover
12. Bolt cover
13. Recline lever
14. Seat cushion outer finisher
15. Leg cover
16. Seat cushion rear finisher
17. Seat cushion lift knobs
18. Lumbar support assembly
19. Seatback frame without side air bag
20. Seatback board
21. Headrest holder with multi position
lock
22
Headrest holder
23
Lumbar support lever knob
24. Snap ring
SE-88
FRONT SEAT
2007 Pathfinder
Conventional Passenger Seat
LIIA2408E
1.
Seatback trim without side air bag
2.
Headrest
3.
Seatback assembly with side air bag
4.
Switch assembly
5.
Power seat switch escutcheon
6.
Recliner switch knob
FRONT SEAT
SE-89
C
D
E
F
G
H
J
K
L
M
A
B
SE
2007 Pathfinder
7.
Slide switch knob
8.
Seat cushion assembly
9.
Seat cushion outer cover
10. Leg cover
11. Seat cushion front finisher
12. Passenger seat wiring harness
13. Power seat frame assembly
14. Seat cushion inner finisher
15. Seat belt buckle assembly
16. Leg cover
17. Seat cushion rear finisher
18. Manual seat frame assembly
19. Recline lever
20. Seat cushion rear finisher
21. Seatback board
22. Headrest holder with multi position
lock
23. Headrest holder
24. Seatback pad without side air bag
25. Seatback frame without side air bag
26. Damper assembly
27. Seatback heating element
SE-90
FRONT SEAT
2007 Pathfinder
Fold Flat Passenger Seat
LIIA2409E
1.
Front seatback lever
2.
Seatback trim without side air bag
3.
Headrest
4.
Seatback assembly with side air bag
5.
Seat cushion assembly
6.
Seat cushion outer finisher
FRONT SEAT
SE-91
C
D
E
F
G
H
J
K
L
M
A
B
SE
2007 Pathfinder
Removal and Installation
EIS007W4
REMOVAL
When removing or installing the seat trim, handle it carefully to keep dirt out and avoid damage.
CAUTION:
●
Before removing the front seat, turn the ignition switch off, disconnect both battery cables and
wait at least 3 minutes.
●
When checking the power seat circuit for continuity using a circuit tester, do not confuse its con-
nector with the side air bag module connector. Such an error may cause the air bag to deploy.
●
Do not drop, tilt, or bump the side air bag module while installing the seat. Always handle it with
care.
●
After front side air bag module inflates, front seatback assembly must be replaced.
●
Front passenger seat is equipped with an Occupant Classification System sensor and control
module. Do not disassemble front passenger seat cushion assembly or remove the trim as this
will affect the Occupant Classification System calibration.
●
Always replace passenger seat cushion as an assembly.
1.
Slide the seat until the four body bolts are visible and a tool can be inserted.
NOTE:
Set the front/rear cushion lifters to the top position.
2.
Disconnect both battery cables and wait at least 3 minutes.
3.
Disconnect the side air bag module harness connector (if equipped).
4.
Remove the four body bolts.
5.
Disconnect the power seat harness connectors and remove the seat from the vehicle.
NOTE:
When removing and installing the seat, use shop cloths to protect the vehicle from damage.
INSTALLATION
Installation is in the reverse order of removal.
Seatback Assembly
EIS007W5
REMOVAL
NOTE:
On vehicles equipped with side air bags, only complete seatback assemblies can be replaced.
1.
Remove the front seat assembly. Refer to
SE-91, "Removal and Installation"
2.
Remove the seatback board from the back of the seatback.
7.
Leg cover
8.
Seat frame assembly
9.
Passenger seat wiring harness
10. Seat cushion inner cover
11. Leg cover
12. Seat belt buckle assembly
13. Inboard reclining arm outer cover
14. Inboard reclining arm inner cover
15. Outboard reclining arm inner cover
16. Outboard reclining arm outer cover
17. Seat cushion rear finisher
18. Seatback board
19. Headrest holder with multi position
lock
20. Headrest holder
21. Seatback pad without side air bag
22. Seat back frame without side air bag 23. Seatback fold flat release lever
assembly
24. Damper assembly
PIIA0163E
SE-92
FRONT SEAT
2007 Pathfinder
3.
Remove the retainer.
4.
Disconnect the seatback heater harness.
5.
Remove the seatback bolts (2 for each side) and seatback assembly.
DISASSEMBLY
NOTE:
On vehicles equipped with side air bags, only complete seatback assemblies can be replaced.
1.
Remove the seatback assembly. Refer to
.
2.
Remove the headrest.
3.
From inside of the seatback, squeeze the headrest holder tabs
at the base of the stay pipe and pull up to remove.
NOTE:
Before installing the headrest holder, check its orientation (front/
rear and right/left).
4.
Remove the snap ring and the lumbar support lever knob.
5.
Remove the seatback trim and pad assembly.
6.
Remove the hog ring to separate the seatback trim from the pad and the heating element (if equipped).
ASSEMBLY
Assembly is in the reverse order of disassembly.
INSTALLATION
Installation is in the reverse order of removal.
Seat Cushion Trim and Pad
EIS008IE
REMOVAL
CAUTION:
●
Front passenger seat is equipped with an Occupant Classification System sensor and control
module. Do not disassemble front passenger seat cushion assembly or remove the trim as this
will affect the Occupant Classification System calibration.
SIIA0113E
LRS023
PIIA1156E
FRONT SEAT
SE-93
C
D
E
F
G
H
J
K
L
M
A
B
SE
2007 Pathfinder
●
Always replace passenger seat cushion as an assembly.
●
When removed, the passenger seat cushion must always be placed pan side UP to prevent dam-
age.
●
During installation, the wire harness clips must be reinstalled in the holes they were originally in.
Do not add additional clips.
●
The Occupant Classification System control module can only be replaced as part of the seat cush-
ion assembly.
1.
Remove the front seat assembly. Refer to
SE-91, "Removal and Installation"
2.
Remove the power seat switch knobs and power seat switch
escutcheon (if equipped) (or lift knobs on manual seats). .
3.
Remove the seat cushion outer finisher.
4.
Remove the power seat switch screws .
5.
Remove four bolts and the seat cushion assembly.
●
On the fold flat passenger seat it is necessary to unclip the
rear flap j-clip from the seat pan.
6.
Remove the retainer on the seat cushion frame, then remove the harness connector for the seat cushion
heater (if equipped).
DISASSEMBLY
CAUTION:
●
Front passenger seat is equipped with an Occupant Classification System sensor and control
module. Do not disassemble front passenger seat cushion assembly or remove the trim as this
will affect the Occupant Classification System calibration.
1.
Remove the seat cushion assembly. Refer to .
2.
On the drivers seat only, remove the hog rings to separate the trim cover from the pad and seat cushion
heater unit.
LIIA0681E
LIIA0285E
SIIA0503E
SE-94
FRONT SEAT
2007 Pathfinder
ASSEMBLY
Assembly is in the reverse order of disassembly.
INSTALLATION
Installation is in the reverse order of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст