Nissan Pathfinder (2007 year). Manual — part 36
DISASSEMBLY
AT-259
D
E
F
G
H
I
J
K
L
M
A
B
AT
2007 Pathfinder
5.
Remove O-ring from input clutch assembly.
6.
Remove oil pump assembly to transmission case bolts.
7.
Remove the oil pump assembly evenly from the transmission
case using Tools.
CAUTION:
●
Fully tighten the sliding hammer screws.
●
Make sure that bearing race is installed to the oil pump
assembly edge surface.
8.
Remove O-ring from oil pump assembly.
SCIA5011E
SCIA2300E
Tool number
: ST25850000 (J-25721-A)
SCIA5474E
SCIA5172E
AT-260
DISASSEMBLY
2007 Pathfinder
9.
Remove bearing race from oil pump assembly.
10. Remove needle bearing from front sun gear.
11. Remove front sun gear assembly from front carrier assembly.
NOTE:
Remove front sun gear by rotating it left and right.
12. Remove seal rings from input clutch assembly.
13. Remove front carrier assembly (with input clutch assembly and
rear internal gear) from rear carrier assembly.
CAUTION:
Do not remove it with needle bearing.
SCIA6529E
SCIA2808E
SCIA5014E
SCIA2470E
SCIA5015E
DISASSEMBLY
AT-261
D
E
F
G
H
I
J
K
L
M
A
B
AT
2007 Pathfinder
14. Loosen lock nut and remove band servo anchor end pin from
transmission case.
15. Remove brake band from transmission case.
CAUTION:
●
To prevent brake linings from cracking or peeling, do not
stretch the flexible band unnecessarily. When removing
the brake band, always secure it with a clip as shown.
●
Check brake band facing for damage, cracks, wear or
burns.
16. Remove mid carrier assembly and rear carrier assembly as a
unit.
SCIA6512E
SCIA2580E
SAT655
SCIA5017E
AT-262
DISASSEMBLY
2007 Pathfinder
17. Remove mid carrier assembly from rear carrier assembly.
18. Remove needle bearing (front side) from mid carrier assembly.
19. Remove needle bearing (rear side) from mid carrier assembly.
20. Remove bearing race from rear carrier assembly.
21. Remove needle bearing from rear carrier assembly.
SCIA5697E
SCIA2805E
SCIA2804E
SCIA5175E
SCIA2803E
DISASSEMBLY
AT-263
D
E
F
G
H
I
J
K
L
M
A
B
AT
2007 Pathfinder
22. Remove mid sun gear assembly, rear sun gear assembly and
high and low reverse clutch hub as a unit.
CAUTION:
Remove them with bearing race and needle bearing.
23. Remove high and low reverse clutch assembly from direct clutch
assembly.
CAUTION:
Make sure that needle bearing is installed to the high and
low reverse clutch assembly edge surface.
24. Remove needle bearing from drum support.
25. Remove direct clutch assembly from reverse brake.
26. Remove snap ring from A/T assembly harness connector.
SCIA5018E
SCIA2306E
SCIA5198E
SCIA5019E
SCIA5021E
AT-264
DISASSEMBLY
2007 Pathfinder
27. Push A/T assembly harness connector.
CAUTION:
Do not damage connector.
28. Remove oil pan and oil pan gasket.
29. Check foreign materials in oil pan to help determine causes of
malfunction. If the A/T fluid is very dark, smells burned, or con-
tains foreign particles, the frictional material (clutches, band)
may need replacement. A tacky film that will not wipe clean indi-
cates varnish build up. Varnish can cause valves, servo, and
clutches to stick and can inhibit pump pressure.
●
If frictional material is detected, perform A/T fluid cooler
cleaning. Refer to
AT-15, "A/T Fluid Cooler Cleaning"
30. Remove magnets from oil pan.
31. Straighten terminal clips to free terminal cord assembly and A/T
fluid temperature sensor 2 harness.
32. Disconnect A/T fluid temperature sensor 2 connector.
CAUTION:
Do not damage connector.
SCIA5022E
SCIA2308E
SCIA5199E
SCIA5200E
SCIA5446E
DISASSEMBLY
AT-265
D
E
F
G
H
I
J
K
L
M
A
B
AT
2007 Pathfinder
33. Straighten terminal clip to free revolution sensor harness.
34. Disconnect revolution sensor connector.
CAUTION:
Do not damage connector.
35. Remove bolts (A), (B) and (C) from control valve with TCM.
36. Remove control valve with TCM from transmission case.
CAUTION:
When removing, be careful with the manual valve notch and
manual plate height. Remove it vertically.
37. Remove A/T fluid temperature sensor 2 with bracket from con-
trol valve with TCM.
38. Remove bracket from A/T fluid temperature sensor 2.
SCIA7526E
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA5025E
SCIA5260E
SCIA5301E
SCIA5264E
AT-266
DISASSEMBLY
2007 Pathfinder
39. Remove O-ring from A/T assembly harness connector.
40. Disconnect TCM connectors.
CAUTION:
Do not damage connectors.
41. Remove A/T assembly harness connector from control valve
with TCM using suitable tool.
42. Disconnect TCM connector and park/neutral position switch
connector.
CAUTION:
Do not damage connectors.
43. Remove rear extension assembly (2WD models) or adapter case assembly (4WD models) according to
the following procedures.
SCIA5155E
SCIA5447E
SCIA5448E
SCIA5449E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст