Nissan Pathfinder (2007 year). Manual — part 32
ON-VEHICLE SERVICE
AT-227
D
E
F
G
H
I
J
K
L
M
A
B
AT
2007 Pathfinder
Control Valve With TCM and A/T Fluid Temperature Sensor 2
ECS00ELU
COMPONENTS
1.
Transmission
2.
Snap ring
3.
Sub-harness
4.
Control valve with TCM
5.
Bracket
6.
A/T fluid temperature sensor 2
7.
Oil pan gasket
8.
Oil pan
9.
Magnet
10. Drain plug
11.
Drain plug gasket
12. Oil pan bolt
13. Terminal cord assembly
14. O-ring
SCIA5478E
AT-228
ON-VEHICLE SERVICE
2007 Pathfinder
CONTROL VALVE WITH TCM REMOVAL AND INSTALLATION
Removal
1.
Disconnect negative battery terminal.
2.
Drain A/T fluid. Refer to
.
3.
Disconnect A/T assembly harness connector.
4.
Remove snap ring from A/T assembly harness connector.
5.
Push A/T assembly harness connector.
CAUTION:
Do not damage connector.
6.
Remove oil pan and oil pan gasket. Refer to
7.
Straighten the terminal clip to free the terminal cord assembly for
A/T fluid temperature sensor 2 harness.
8.
Disconnect A/T fluid temperature sensor 2 connector.
CAUTION:
Do not damage connector.
9.
Straighten terminal clip to free the revolution sensor harness.
10. Disconnect revolution sensor connector.
CAUTION:
Do not damage connector.
SCIA5021E
SCIA5022E
SCIA5446E
SCIA7525E
ON-VEHICLE SERVICE
AT-229
D
E
F
G
H
I
J
K
L
M
A
B
AT
2007 Pathfinder
11. Remove bolts (A), (B) and (C) from control valve with TCM.
12. Remove control valve with TCM from transmission case.
CAUTION:
When removing, be careful with the manual valve notch and
manual plate height. Remove it vertically.
13. Remove A/T fluid temperature sensor 2 with bracket from con-
trol valve with TCM.
14. Remove bracket from A/T fluid temperature sensor 2.
15. Remove O-ring from A/T assembly harness connector.
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA5139E
SCIA5142E
SCIA5301E
SCIA5264E
SCIA5155E
AT-230
ON-VEHICLE SERVICE
2007 Pathfinder
16. Disconnect TCM connectors.
CAUTION:
Do not damage connectors.
17. Remove A/T assembly harness connector from control valve
with TCM using suitable tool.
18. Disconnect TCM connector and park/neutral position switch
connector
CAUTION:
Do not damage connectors.
SCIA5447E
SCIA5448E
SCIA5449E
ON-VEHICLE SERVICE
AT-231
D
E
F
G
H
I
J
K
L
M
A
B
AT
2007 Pathfinder
Installation
CAUTION:
After completing installation, check A/T fluid leakage and fluid level. Refer to
1.
Connect TCM connector and park/neutral position switch con-
nector.
2.
Install A/T assembly harness connector to control valve with
TCM.
3.
Connect TCM connector.
4.
Install new O-ring in A/T assembly harness connector.
CAUTION:
●
Do not reuse O-ring.
●
Apply ATF to O-ring.
SCIA5449E
SCIA5450E
SCIA5447E
SCIA5155E
AT-232
ON-VEHICLE SERVICE
2007 Pathfinder
5.
Install A/T fluid temperature sensor 2 to bracket.
6.
Install A/T fluid temperature sensor 2 (with bracket) to control
valve with TCM. Tighten A/T fluid temperature sensor 2 bolt to
the specified torque. Refer to
.
CAUTION:
Adjust bolt hole of bracket to bolt hole of control valve with
TCM.
7.
Install control valve with TCM in transmission case.
CAUTION:
●
Make sure that turbine revolution sensor is securely
installed into turbine revolution sensor hole.
●
Hang down revolution sensor harness toward outside so
as not to disturb installation of control valve with TCM.
●
Adjust A/T assembly harness connector of control valve
with TCM to terminal hole of transmission case.
●
Assemble it so that manual valve cutout is engaged with
manual plate projection.
SCIA5264E
SCIA5301E
SCIA5034E
SCIA5142E
ON-VEHICLE SERVICE
AT-233
D
E
F
G
H
I
J
K
L
M
A
B
AT
2007 Pathfinder
8.
Install bolts (A), (B) and (C) in control valve with TCM.
9.
Tighten bolt (1), (2) and (3) temporarily to prevent dislocation.
After that tighten them in order (1
→
2
→
3). Then tighten other
bolts.
10. Tighten control valve with TCM bolts to the specified torque.
Refer to
11. Connect A/T fluid temperature sensor 2 connector.
12. Securely fasten terminal cord assembly and A/T fluid tempera-
ture sensor 2 harness with terminal clips.
13. Connect revolution sensor connector.
14. Securely fasten revolution sensor harness with terminal clip.
15. Install oil pan to transmission case. Refer to
.
Bolt symbol
Length mm (in)
Number of bolts
A
42 (1.65)
5
B
55 (2.17)
6
C
40 (1.57)
1
SCIA5139E
SCIA5140E
SCIA5446E
SCIA7525E
AT-234
ON-VEHICLE SERVICE
2007 Pathfinder
16. Pull up A/T assembly harness connector.
CAUTION:
Do not damage connector.
17. Install snap ring to A/T assembly harness connector.
18. Connect A/T assembly harness connector.
19. Connect the negative battery terminal.
20. Refill the A/T with fluid and check the fluid level and for fluid
leakage. Refer to
A/T FLUID TEMPERATURE SENSOR 2 REMOVAL AND INSTALLATION
Removal
1.
Disconnect negative battery terminal.
2.
Drain A/T fluid. Refer to
.
3.
Remove oil pan and oil pan gasket. Refer to
4.
Straighten terminal clip to free A/T fluid temperature sensor 2
harness.
5.
Disconnect A/T fluid temperature sensor 2 connector.
CAUTION:
Do not damage connector.
6.
Remove A/T fluid temperature sensor 2 with bracket from con-
trol valve with TCM.
SCIA5038E
SCIA5039E
SCIA5146E
SCIA5253E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст